Epson C 2900 Manual

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 37 Confidential 
13) Release the two hooks of the COVER 
DRAWER (PL1.2.15), remove the 
COVER DRAWER from the HOLDER 
ASSY FRONT R. 
13.1
13.1
13.2
14) Release the harness of the HARN 
ASSY DUP RELAY (PL1.2.13) from the 
hooks of the HOLDER ASSY FRONT R. 
15) Release the two hooks on the 
connector (P272) of the HARN ASSY 
DUP RELAY, pull out the harness and 
connector (J271) through the hole on the 
HOLDER ASSY  FRONT  R, and remove 
the HARN ASSY DUP RELAY. 
 
15.1
15.2
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 38 Confidential 
[Replacement] 
1) Pass the connector (P271) and the 
harness of the HARN ASSY DUP RELAY 
through the hole on the HOLDER ASSY 
FRONT R, and secure the connector 
(P272) of the HARN ASSY DUP RELAY to 
the HOLDER ASSY FRONT R with the 
two hooks. 
 
2) Route the harness of the HARN ASSY 
DUP RELAY along the hooks of the 
HOLDER ASSY  FRONT R. 
3) Attach the COVER DRAWER to the 
HOLDER ASSY FRONT R, secure the 
COVER DRAWER with the two hooks.  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 39 Confidential 
4) Attach the HOLDER
 ASSY FRONT R to 
the COVER ASSY FRONT MG. 
Note: When carrying out the work this 
procedure, take care not to damage the 
harness by pinching it between the 
HOLDER ASSY FRONT R and the 
COVER ASSY FRONT MG. 
 
5) Secure the HOLD ER ASSY  FRONT R 
to the COVER ASSY FRONT MG with the 
three screws (silver, tap, 8mm).  
 
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 40 Confidential 
RRP1.13 SHAFT PIVOT (PL1.2.23) 
[Removal] 
1) Remove the CASSETTE ASSY 250. (RRP2.1) 
2) Release the hook of the SHAFT PIVOT 
(PL1.2.23) to pull out the SHAFT PIVOT. 
 
 
[Replacement] 
1) Mate the flat face of the SHAFT PIVOT 
with the hole of the COVER ASSY FRONT 
MG, push the SHAFT PIVOT until the hook 
is locked. 
 
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 41 Confidential 
RRP2. PAPER CASSETTE 
RRP2.1 CASSETTE ASSY
  250 (PL2.1.1)   
[Removal]
 
1) Pull out the CASSETTE ASSY 250 
(PL2.1.1) from the printer. 
 
 
[Replacement] 
1) Insert the CASSETTE ASSY 250 into 
the printer. 
 
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 42 Confidential 
RRP2.2 HOLDER ASSY RETARD (PL2.1.5)   
[Removal] 
1) Remove the CASSETTE ASSY 250. (RRP2.1) 
2) Release the two hooks of the HOLDER 
ASSY RETARD (PL2.1.5). 
3) Pull up the HOLDER ASSY RETARD to 
remove the HOLDER ASSY RETARD 
from the CASSETTE ASSY 250 (PL2.1.1).
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 43 Confidential 
[Replacement] 
1) Mate the under tab of the HOLDER 
ASSY RETARD with the hole of the 
CASSETTE ASSY  250. 
2) Secure the left and right hooks of the 
HOLDER ASSY  RETARD. 
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 44 Confidential 
RRP2.3 HANDLE ASSY CST (PL2.1.19) 
[Removal] 
1) Remove the CASSETTE ASSY 250. (RRP2.1) 
2) Release the left side holes of the 
HANDLE ASSY CST (PL2.1.19) from the 
bosses of the CASSETTE ASSY 250 
(PL2.1.1), using a miniature screwdriver. 
3) Release the right side holes of the 
HANDLE ASSY CST from the bosses of 
the CASSETTE ASSY 250, remove the 
HANDLE ASSY CST. 
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 45 Confidential 
[Replacement] 
1) Mate the right side holes of the 
HANDLE ASSY CST with the bosses of 
the CASSETTE ASSY 250. 
2) Mate the left side holes of the HANDLE 
ASSY CST with the bosses of the 
CASSETTE ASSY 250, attach the 
HANDLE ASSY CST. 
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 46 Confidential 
RRP3. PAPER FEEDER 
RRP3.1 CLUTCH ASSY DRV (PL3.1.1), BEARING REGI (PL3.1.2)   
[Removal] 
1) Remove the CASSETTE ASSY 250. (RRP2.1) 
2) Open the COVER ASSY FRONT MG (PL1.2.1). 
3) Open the TRANSFER ASSY (PL6.1.7). 
Note: Cover the drum of the DRUM CARTRIDGE to avoid exposure to light.  
4) Remove the DRUM CARTRIDGE. (RRP4.6)  
Note: The FUSING part is very hot. Take added care not to get burned when performing the 
service operation. 
5) Remove the FUSER UNIT. (RRP6.1) 
6) Remove the COVER SIDE L. (RRP1.7) 
7) Release the harness of the CLUTCH 
ASSY DRV (PL3.1.1) from the hook of the 
DRIVE ASSY PH (PL7.1.4). 
Note: When carrying out the work described below, leave the relay connector on the printer 
harness side. 
8) Disengage the connector (P/J262) of 
the CLUTCH ASSY DRV.