Home > Epson > Printer > Epson C 2900 Manual

Epson C 2900 Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Epson C 2900 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 681
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 217 Confidential 
     
    RRP8.9 PWBA MCU (PL8.2.13)   
    [Removal] 
    Note: Never fail to perform the diagnostic operation. Otherwise the data will be lost in the worst 
    case. 
    Note: Use the wrist strap to protect the PWB from the electrostatic. 
    1) Perform the NVM Save to evacuate the MCU data. 
    2) Turn on the power while pressing the  ▲ key and  ▼ key on the control panel. 
    3) Enter the password, press the  ▼ key twice, and press the [OK] key once. The diagnostic screen 
    comes up. 
    4) Press the [OK] key once. 
    5) Press the  ▼ key several times until IOT Diag is  displayed. Press the [OK] key once. 
    6) Press the  ▼ key several times until NVM Settings is displayed. Press the [OK] key once. 
    7) Press the  ▼ key several times until SaveNVM to ESS is displayed. Press the [OK] key once. 
    8) Press the [OK] key once, and NVM Save is performed. 
    9) After NVM Save is complete, press the [STOP] key several times until IOT Diag is displayed. 
    10) Press the  ▼ key several times until Complete is displayed. 
    11) Press the [OK] key two times. “Ready” are displayed. 
    12) Turn off the power to exit. 
    13) Remove the POWER CORD from outlet. 
    14) Remove the CASSETTE ASSY 250. (RRP2.1) 
    15) Open the COVER ASSY FRONT MG (PL1.2.1). 
    Note: Cover the drum of the DRUM CARTRIDGE to avoid exposure to light.  
    16) Remove the DRUM CARTRIDGE. (RRP4.6)  
    Note: The FUSING part is very hot. Take added care not to get burned when performing the 
    service operation. 
    17) Remove the FUSER UNIT. (RRP6.1) 
    18) Remove the COVER ASSY WINDOW TNR. (RRP1.6) 
    19) Remove the COVER ASSY TOP. (RRP1.1) 
    20) Remove the COVER SIDE R. (RRP1.5) 
    21) Remove the COVER SIDE L. (RRP1.7) 
    22) Remove the COVER REAR. (RRP1.3) 
    23) Remove the FAN. (RRP8.1) 
    24) Remove the PWBA ESS SFP. (RRP8.3)  
    						
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 218 Confidential 
     
    25) Remove the five screws (silver, 6mm) 
    that fix the FRAME ESS (PL8.1.5) to the 
    printer. 
    26) Swing the FRAME ESS slightly up and 
    back as if it were hinged at the top. 
    27) Remove the hole of the FRAME ESS 
    from the hook of the FRAME ASSY LVPS 
    (PL8.2.3) by lifting the FRAME ESS 
    slightly. Remove the FRAME ESS from the 
    printer together with the DUCT FAN 
    (PL8.1.2).   
    						
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 219 Confidential 
     
    28) Disengage all the connectors of the 
    PWBA MCU (PL8.2.13). 
    29) Remove the six screws (silver, 6mm) 
    that fix the PWBA MCU to the printer. 
      
    						
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 220 Confidential 
     
    30) Remove the PWBA MCU from the 
    printer.  
    						
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 221 Confidential 
     
    [Replacement] 
    Note: Use the wrist strap to protect the PWB from the electrostatic.  
    1) Mate the holes of the PWBA MCU with 
    the tabs of the printer, attach it. 
    2) Secure the PWBA MCU to the printer 
    with the six screws (silver, 6mm). 
      
    						
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 222 Confidential 
     
    3) Engage all the connectors of the PWBA 
    MCU. 
     
    4) Mate the hole of the FRAME ESS with 
    the hook of the FRAME ASSY LVPS.  
    						
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 223 Confidential 
     
    5) Attach the DUCT FAN to the printer 
    together with the FRAME ESS. 
    6) Secure the FRAME ESS to the printer 
    with the five screws (silver, 6mm). 
     
    Note: When the PWBA MCU is replaced with a new one, perform the following steps. 
    (After completing all the steps .) 
    7) Plug in the power cord to the printer. 
    8) Execute diagnostic operation of NVM Load, and write the data into PWBA MCU. 
    9) Turn off the power. 
    10) Perform the diagnostic operation of NV M Load, and write the data into the MCU. 
    11) Turn on the power while pressing the  ▲ key and  ▼ key on the control panel. 
    12) Enter the password, press the  ▼key twice, and press the [OK]  key once. The diagnostic screen 
    comes up. 
    13) Press the  ▼ key several times until IOT Diag is displayed. Press the [OK] key once. 
    14) Press the  ▼ key several times until NVM Settings is displayed. Press the [OK] key once. 
    15) Press the  ▼ key several times until LoadNVM from ESS  is displayed. Press the [OK] key once. 
    16) Press the [OK] key once, and NVM Load is performed. 
    17) After NVM Load is complete, press the [STOP] ke y several times until IOT Diag is displayed. 
    18) Press the  ▼ key several times until Complete is displayed.  
    						
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 224 Confidential 
     
    19) Press the [OK] key twice. “Ready” is displayed. 
    20) Turn off the power to exit.  
    						
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 225 Confidential 
     
    RRP9. DUPLEX (Option) 
    RRP9.1 FEEDER ASSY DUP SFP STD (PL11.1.1)   
    [Removal] 
    1) Open the COVER ASSY FRONT MG (PL1.2.1). 
    2) While pushing the LATCH BUTTON, lift 
    up the FEEDER ASSY DUP SFP STD 
    from the printer. 
    2.1
    2.2 
    						
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 226 Confidential 
     
    [Replacement] 
    1) Align the arrow on the FEEDER ASSY 
    DUP SFP STD with the one on the 
    COVER ASSY FRONT MG, attach the 
    FEEDER ASSY DUP SFP STD. 
    2) Push the FEEDER ASSY DUP SFP 
    STD to secure it. 
    3) Close the COVER ASSY FRONT MG.  
    						
    All Epson manuals Comments (0)

    Related Manuals for Epson C 2900 Manual