Epson C 2900 Manual

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 227 Confidential 
 
RRP9.2 ROLLER ASSY DUP (PL11.2.9)   
[Removal] 
1) Open the COVER ASSY FRONT MG (PL1.2.1). 
2) Remove the FEEDER ASSY DUP SFP STD. (RRP9.1) 
3) Release the six hooks that fixes the 
COVER PWBA DUP (PL11.1.15), remove 
the COVER PWBA DUP from the 
FEEDER ASSY DUP SFP STD 
(PL11.1.1). 
 
3.1
3.2
3.3
4) Disengage the connector (P/J603) of 
the DRIVE ASSY DUP (PL11.2.5) on the 
PWBA DUP (PL11.1.16), release the 
harness of the DRIVE ASSY DUP from the 
hooks of the COVER DRIVE DUP 
(PL11.2.3). 
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 228 Confidential 
 
5) Release the five hooks of the COVER 
DRIVE DUP. Draw out the connector of 
the DRIVE ASSY DUP from the hole of the 
COVER DRIVE DUP, and then remove 
the COVER DRIVE DUP from the 
FEEDER ASSY DUP SFP STD. 
 
5.1
5.2
6) Remove the four screws (silver, tap, 
8mm) that fix the DRIVE ASSY DUP to the 
FEEDER ASSY DUP SFP STD
, remove 
the DRIVE ASSY DUP. 
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 229 Confidential 
 
7) Release the hook of the GEAR ROLL 
DUP (PL11.2.6), remove the GEAR ROLL 
DUP from the ROLLER ASSY DUP 
(PL11.2.9). 
 
8) Remove the BEARING DUP (PL11.2.7) 
that fixes the right and left sides of the 
ROLLER ASSY DUP by rotating in the 
direction shown by the arrow. 
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 230 Confidential 
 
9) Remove the ROLLER ASSY DUP from 
the FEEDER ASSY DUP SFP STD. 
 
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 231 Confidential 
 
[Replacement] 
1) Attach the ROLLER ASSY DUP to the 
FEEDER ASSY DUP SFP STD. 
 
2) Replace the BEARING DUP on both the 
right and left sides of the ROLLER ASSY 
DUP by matching the tab of the BEARING 
DUP with the notch of the FEEDER ASSY 
DUP SFP STD. 
Clamp the BEARING DUP firmly to the 
FEEDER ASSY DUP SFP STD. 
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 232 Confidential 
 
3) Attach the GEAR ROLL DUP to the 
ROLLER ASSY DUP, mate the hook of 
the GEAR ROLL DUP with the groove of 
the FEEDER ASSY DUP SFP STD. 
 
4) Attach the DRIVE ASSY DUP to the 
FEEDER ASSY DUP SFP STD, secure 
the DRIVE ASSY DUP with the four 
screws (silver, tap, 8mm). 
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 233 Confidential 
 
5) Draw the connector of the DRIVE ASSY 
DUP through the hole of the COVER 
DRIVE DUP. Then fix the COVER DRIVE 
DUP to the FEEDER ASSY DUP SFP 
STD using the five hooks. 
 
5.2
5.3
5.1
6) Route the harness of the DRIVE ASSY 
DUP along the hooks of the COVER 
DRIVE DUP, engage the connector 
(P/J603) of the DRIVE ASSY DUP to the 
PWBA DUP. 
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 234 Confidential 
 
Note: When carrying out the steps 
described below, insert the right edge 
of the COVER PWBA DUP into the 
clearance of the CHUTE DUP FRAME. 
7) Attach the COVER PWBA DUP to the 
FEEDER ASSY DUP SFP STD, secure 
the COVER PWBA DUP with the six 
hooks. 
 
7.3
7.2
7.1
8) Replace the FEEDER ASSY DUP SFP STD. (Replacement 57) 
9) Close the 
COVER ASSY FRONT MG.  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 235 Confidential 
 
RRP10. 250 OPTION FEEDER 
RRP10.1 FEEDER ASSY OPT (PL12.1.3)   
[Removal] 
Note: The printer must be lifted by two people. 
1) Remove the CASSETTE ASSY 250. (RRP2.1) 
2) Remove the two SCREW JOINTs 
(PL12.1.2) that fix the FEEDER ASSY 
OPT (PL12.1.3) to the printer. 
 
3) Lift up the printer to separate it from the 
FEEDER ASSY  OPT. 
2)
2)
3)
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 236 Confidential 
 
[Replacement] 
Note: The printer must be lifted by two people. 
1) Place the printer on the FEEDER ASSY 
OPT with the five holes on the bottom of 
the printer aligned with the studs on the 
FEEDER ASSY  OPT. 
 
2) Secure the printer to the FEEDER 
ASSY OPT using the two SCREW JOINTs.
2)
2)
1)
 
3) Insert the CASSETTE ASSY 250 OPT into the FEEDER ASSY OPT. 
4) Insert the CASSETTE ASSY 250 into the printer.