Epson C 2900 Manual

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 7 Confidential 
RRP1.2 TRAY EXT MAIN (PL1.1.2)   
[Removal] 
1) Remove the CASSETTE ASSY 250. (RRP2.1) 
2) Open the COVER ASSY FRONT MG (PL1.2.1). 
3) Open the TRANSFER ASSY (PL6.1.7) . 
Note: Cover the drum of the DRUM CARTRIDGE to avoid exposure to light.  
4) Remove the DRUM CARTRIDGE. (RRP4.6) 
Note: The FUSING part is very hot. Take added care not to get burned when performing the 
service operation. 
5) Remove the FUSER UNIT. (RRP6.1) 
6) Remove the COVER CST. (RRP1.4) 
7) Remove the COVER ASSY WINDOW TNR. (RRP1.6) 
8) Remove the COVER SIDE R. (RRP1.5) 
9) Remove the COVER SIDE L. (RRP1.7) 
10) Remove the COVER REAR. (RRP1.3) 
11) Slide the TRAY EXT (PL1.1.2) backwa rd until its edge touches the machine. 
12) Release the stopper of the TRAY EXT 
MAIN by depressing the  center section of 
the rear end of the GUIDE TRAY 
(PL1.1.24), and then remove the TRAY 
EXT MAIN. 
12)-1
12)-2
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 8 Confidential 
[Replacement] 
1) Replace the TRAY EXT MAIN on the 
COVER ASSY TOP and then slide the 
TRAY EXT MAIN forward until the stopper 
is fully locked. 
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 9 Confidential 
RRP1.3 COVER REAR (PL1.1.3)   
[Removal] 
1) Remove the CASSETTE ASSY 250. (RRP2.1) 
2) Open the COVER ASSY FRONT MG (PL1.2.1). 
3) Open the TRANSFER ASSY (PL6.1.7) . 
Note: Cover the drum of the DRUM CARTRIDGE to avoid exposure to light.  
4) Remove the DRUM CARTRIDGE. (RRP4.6) 
Note: The FUSING part is very hot. Take added care not to get burned when performing the 
service operation. 
5) Remove the FUSER UNIT. (RRP6.1) 
6) Remove the COVER CST. (RRP1.4) 
7) Remove the COVER ASSY WINDOW TNR. (RRP1.6) 
8) Remove the COVER SIDE R. (RRP1.5) 
9) Remove the COVER SIDE L. (RRP1.7) 
10) Remove the two screws (silver, tap, 
8mm) that fix the COVER REAR (PL1.1.3) 
to the printer. 
 
11) Release the two tabs of the COVER 
REAR from the holes of the COVER ASSY 
TOP (PL1.1.1), remove the COVER REAR 
from the printer. 
10)
10)
11 )
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 10 Confidential 
[Replacement] 
1) Mate the two tabs of the COVER REAR 
with the holes of the COVER ASSY TOP, 
attach the COVER REAR. 
 
2) Secure the COVER REAR to the printer 
with the two screws (silver, tap, 8mm). 
2)
2)
1)
 
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 11 Confidential 
RRP1.4 COVER CST (PL1.1.5) 
[Removal] 
1) Remove the CASSETTE ASSY 250. (RRP2.1) 
2) Press the left and right sides of the 
COVER CST (PL1.1.5) to release the two 
hooks from the holes of the printer, remove 
it. 
2)-1
2)-1
2)-2
 
 
[Replacement] 
1) Attach the COVER CST, secure the left 
and right hooks of the COVER CST. 
1)-2
1)-2
1)-1
 
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 12 Confidential 
RRP1.5 COVER SIDE R (PL1.1.6) 
[Removal] 
1) Remove the CASSETTE ASSY 250. (RRP2.1) 
2) Open the COVER ASSY FRONT MG (PL1.2.1). 
3) Open the TRANSFER ASSY (PL6.1.7) . 
Note: Cover the drum of the DRUM CARTRIDGE to avoid exposure to light.  
4) Remove the DRUM CARTRIDGE. (RRP4.6) 
Note: The FUSING part is very hot. Take added care not to get burned when performing the 
service operation. 
5) Remove the FUSER UNIT. (RRP6.1) 
6) Remove the COVER ASSY WINDOW TNR. (RRP1.6) 
7) Remove the six screws (silver, tap, 
8mm) that fix the COVER SIDE R 
(PL1.1.6) to the printer. 
 
8) Release the front hook of the COVER 
SIDE R. 
 
9) Lift the COVER SIDE R slightly and then 
release the back hook of the COVER SIDE 
R from the groove of the COVER ASSY 
TOP (PL1.1.1). Then remove the COVER 
SIDE R from the printer. 
7)
7)
7)
7)
8) 9)-1
9)-2
7)
7)
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 13 Confidential 
[Replacement] 
1) Set the COVER SIDE R on the printer 
by inserting the back hook of the COVER 
SIDE R into the groove of the COVER 
ASSY TOP. 
 
2) Secure the front hook of the COVER 
SIDE R to the printer. 
 
3) Secure the COVER SIDE R to the 
printer with the six screws (silver, tap, 
8mm). 
3)
3)
3)
3)
2) 1)-1
1)-2
3)
3)
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 14 Confidential 
RRP1.6 COVER ASSY WINDOW TNR (PL1.1.7) 
[Removal] 
1) Open the COVER ASSY WINDOW TNR 
(PL1.1.7). 
 
2) Press the upper hinge of the COVER 
ASSY WINDOW TNR to release the boss 
on the hinge from the hole of the printer, 
move the COVER ASSY WINDOW TNR to 
arrow direction. 
 
3) Remove the COVER ASSY WINDOW 
TNR. 
2)
3)
 
 
[Replacement] 
1) Mate the lower boss of the COVER 
ASSY WINDOW TNR with  the hole of the 
COVER REAR. 
 
2) Bend the upper hinge of the COVER 
ASSY WINDOW TNR, mate the upper 
boss of the COVER ASSY WINDOW TNR 
with the hole of the COVER REAR. Attach 
the COVER ASSY WINDOW TNR. 
 
3) Close the COVER ASSY WINDOW 
TNR. 
2)
1)
 
 
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 15 Confidential 
RRP1.7 COVER SIDE L (PL1.1.19) 
[Removal] 
1) Remove the CASSETTE ASSY 250. (RRP2.1) 
2) Open the COVER ASSY FRONT MG (PL1.2.1). 
3) Open the TRANSFER ASSY (PL6.1.7) . 
Note: Cover the drum of the DRUM CARTRIDGE to avoid exposure to light.  
4) Remove the DRUM CARTRIDGE. (RRP4.6) 
Note: The FUSING part is very hot. Take added care not to get burned when performing the 
service operation. 
5) Remove the FUSER UNIT. (RRP6.1) 
6) Remove the two screws (silver, tap, 
8mm) that fix the COVER SIDE L 
(PL1.1.19) to the printer. 
6)
6)
  
						

							Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 16 Confidential 
7) Release the front hook of the COVER 
SIDE L. 
 
8) Lift the COVER SIDE L slightly and then 
release the back hook of the COVER SIDE 
L from the groove of the COVER ASSY 
TOP (PL1.1.1). 
 
9) Swing the COVER SIDE L to backward, 
to release the three notches of the COVER 
SIDE L from the three hooks of the 
COVER REAR. Remove the COVER SIDE 
L from the printer. 
7)
8)
9)