Home > Epson > Printer > Epson C 2900 Manual

Epson C 2900 Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Epson C 2900 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 681
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 207 Confidential 
     
    RRP8.7 SENSOR HUM (PL8.2.7)   
    [Removal] 
    1) Remove the CASSETTE ASSY 250. (RRP2.1) 
    2) Open the COVER ASSY FRONT MG (PL1.2.1). 
    Note: Cover the drum of the DRUM CARTRIDGE to avoid exposure to light.  
    3) Remove the DRUM CARTRIDGE. (RRP4.6)  
    Note: The FUSING part is very hot. Take added care not to get burned when performing the 
    service operation. 
    4) Remove the FUSER UNIT. (RRP6.1) 
    5) Remove the COVER ASSY TOP. (RRP1.1) 
    6) Remove the COVER SIDE L. (RRP1.7) 
    7) Remove the one screw (silver, tap, 
    8mm) that fixes the SENSOR HUM 
    (PL8.2.7) to the printer, remove the 
    SENSOR HUM. 
    8) Disengage the connector (P/J201) of 
    the SENSOR HUM. 
       
    						
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 208 Confidential 
     
    [Replacement] 
    1) Engage the connecter (P/J201) of the 
    SENSOR HUM. 
    2) Secure the SENSOR HUM to the printer 
    with the one screw (silver, tap, 8mm). 
      
    						
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 209 Confidential 
     
    RRP8.8 SWITCH ASSY INLET MG SFP (P L8.2.9), COVER INLET (PL8.2.22)   
    [Removal] 
    1) Remove the CASSETTE ASSY 250. (RRP2.1) 
    2) Open the COVER ASSY FRONT MG (PL1.2.1). 
    Note: Cover the drum of the DRUM CARTRIDGE to avoid exposure to light.  
    3) Remove the DRUM CARTRIDGE. (RRP4.6)  
    Note: The FUSING part is very hot. Take added care not to get burned when performing the 
    service operation. 
    4) Remove the FUSER UNIT. (RRP6.1) 
    5) Remove the COVER ASSY TOP. (RRP1.1) 
    6) Remove the COVER ASSY WINDOW TNR. (RRP1.6) 
    7) Remove the COVER SIDE R. (RRP1.5) 
    8) Remove the COVER SIDE L. (RRP1.7) 
    9) Remove the COVER REAR. (RRP1.3) 
    10) Disengage the five connectors (P/J20, 
    23, 24, 26 and 28) on the PWBA MCU 
    (PL8.2.13), release the harness from the 
    GUIDE HARNESS AC (PL8.2.6). 
    11) Disengage the connector (P/J48) of 
    the SWITCH ASSY INLET MG SFP 
    (PL8.2.9) from the PWBA LVPS (PL8.2.1).
    Remove the one screw (silver, with 
    washer, 6mm) that fixes the grounding 
    terminal of the SWITCH ASSY INLET MG 
    SFP, release the harness of the SWITCH 
    ASSY INLET MG SFP from the GUIDE 
    HARNESS AC. 
      
    						
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 210 Confidential 
     
    12) Remove the two screws (silver, tap, 
    8mm) that fix the BRACKET SW (PL8.2.8) 
    to the printer. 
    Note: The MAIN SWITCH and the printer are connected with the harness, so they should not be 
    far apart when carrying out the work described next procedure. 
    13) Release the BRAKET SW from the 
    hook together with the MAIN SW. 
    14) Remove the two screws (silver, tap, 
    12mm) that fix the COVER INLET 
    (PL8.2.22) to the printer.  
    						
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 211 Confidential 
     
    15) Release the hooks of the SWITCH 
    POWER, remove the SWITCH POWER of 
    the SWITCH ASSY INLET MG SFP from 
    the BRACKET SW. 
    16) Remove the COVER INLET from the 
    printer, pull out the harness and SWITCH 
    POWER through the hole on the 
    printer, 
    and remove the 
    SWITCH ASSY INLET 
    MG SFP from the printer. 
    17) Release the hooks of the AC INLET, 
    remove the AC INLET of the SWITCH 
    ASSY INLET MG SFP from the COVER 
    INLET.  
    						
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 212 Confidential 
     
    18) Pull out the harness and SWITCH 
    POWER through the hole of the COVER 
    INLET
    . 
    19) Pull out the connector (J48) through 
    the hole of the COVER INLET, and remove 
    the SWITCH ASSY INLET MG SFP from 
    the COVER INLET.  
    						
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 213 Confidential 
     
    [Replacement] 
    1) Route the connector (J48) of the 
    SWITCH ASSY INLET MG SFP through 
    the hole of the COVER INLET. 
    2) Route the harness and SWITCH 
    POWER of the SWITCH ASSY INLET MG 
    SFP through the hole of the COVER 
    INLET. 
    3) Attach the AC INLET of the SWITCH 
    ASSY INLET MG SFP to the COVER 
    INLET, and secure it with the hooks. 
      
    						
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 214 Confidential 
     
    4) Route the harness and SWITCH 
    POWER of the SWITCH ASSY INLET MG 
    SFP through the hole of the printer. 
    Note: When replacing the SWITCH 
    ASSY INLET MG SFP, match the 
    ON/OFF mark of the SWITCH POWER 
    with the mark on the BRACKET SW. 
    5) Attach the SWITCH POWER of the 
    SWITCH ASSY INLET MG SFP to the 
    BRACKET SW, and secure it with the 
    hooks. 
      
    						
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 215 Confidential 
     
    6) Secure the COVER INLET to the printer 
    with the two screws (silver, tap, 12mm). 
    7) Mate the notch of the BRACKET SW 
    with the hook of the GUIDE HARNESS 
    AC. 
    8) Mate the holes of the BRACKET SW 
    with the two bosses of the printer, secure 
    the BRACKET SW with the two screws 
    (silver, tap, 8mm).  
    						
    							Chapter 3 Removal and Replacement Procedures Revision B 
    Epson AcuLaser C2900N 3 - 216 Confidential 
     
    9) Route the harness of the SWITCH 
    ASSY INLET MG SFP along the GUIDE 
    HARNESS AC, secure the grounding 
    terminal of the SWITCH ASSY INLET MG 
    SFP with the one screw (silver, with 
    washer, 6mm). 
    Engage the connector (P/J48) of the 
    SWITCH ASSY INLET MG SFP to the 
    PWBA 
    LVPS. 
    10) Route the harness along the GUIDE 
    HARNESS AC, engage the five connectors 
    (P/J20, 23, 24, 26 and 28) with the PWBA 
    MCU. 
      
    						
    All Epson manuals Comments (0)

    Related Manuals for Epson C 2900 Manual