Panasonic Kx Tva50 Programming Manual

							2.5 System Parameters
Programming Manual 151
4.Click OK.
Select Language
Position of AM/PM in Time Stamp
Specifies the position of the AM/PM announcement.
Default
After (when the Primary Language is set to English [US])
Va l u e  R a n g e
Before: the VPS announces AM/PM before the time, such as P.M. 3:42.
After: the VPS announces AM/PM after the time, such as 3:42 P.M..
24-h: the VPS announces the time in 24-h format, such as 15:42.
Oclock Prompt
Specifies when and if Oclock is announced.
Default
When 0 min (when the Primary Language is set to English [US])
Va l u e  R a n g e
When 0 min: the VPS announces Oclock only on the hour, such one oclock.
Always: the VPS announces Oclock always.
None: No announcement
Month/Day Prompt
Specifies the order of the month and day for date announcements.
Default
MM:DD (when the Primary Language is set to English [US])
Va l u e  R a n g e
MM:DD: Month and Day
DD:MM: Day and Month
# Announcement Mode
Specifies the way of announcement for the # character when English (US) or English (UK) is 
selected as System Guidance.
Default
POUND (when the Primary Language is set to English [US]) 
						

							2.5 System Parameters
152 Programming Manual
Va l u e  R a n g e
POUND, HASH
PBX Parameters
Specifies the parameters used to program the VPS for optimal signaling and performance with the 
PBX.
PBX Environment
Specifies how the VPS will initiate and control call transfers, setup outgoing calls, and control 
message waiting lamps on extensions. For KX-TVA50, the procedure for verifying the correct code 
sequences for non-Panasonic KX-T series PBX is to manually execute the sequences from a single 
line telephone (SLT) with the PBX.
PBX Type
Specifies the type of PBX connected to the VPS. 
						

							2.5 System Parameters
Programming Manual 153
Default
TDA/TAW
Va l u e  R a n g e
TDA/TAW, TD816/TD1232/TA1232, TD500, TD308, TA624, Other*1
Integration Mode
Specifies the method of integrating the VPS with the PBX.
Default
DPT
Va l u e  R a n g e
Inband: The PBX sends DTMF signals to the VPS to indicate the status of calls (busy, answered, 
disconnect, etc.). The DTMF code for each status must be set in the Inband Signaling Parameters; 
the settings of the PBX and VPS must match. If the PBX type is set to a KX-T series PBX, the Inband 
Signaling Parameters will automatically default to the proper codes. This is available with any of the 
following Panasonic KX-T series PBXs: TA624, TA824, TD816, TD1232/TA1232, TD500, TD308, and 
TDA/TAW.
DPT: The VPS communicates with the PBX via the DPT interface. This is available with any of the 
following Panasonic KX-T series PBXs: TD816, TD1232/TA1232, TD500, TD308, and TDA/TAW.
APT: The VPS communicates with the PBX via the APT Interface. This is available with any of the 
following Panasonic KX-T series PBXs: TA624 and TA824.
Feature Manual References
2.1.1 Integration Types
Maximum Extension Number Length
Set this parameter to match the maximum number of digits which the connected PBX recognizes as 
an extension number.
Default
3
Va l u e  R a n g e
2–5 digits
Extension Number of VPS Port 1–6 (KX-TVA50), 1–24 (KX-TVA200)
Specifies the PBX extension number of the port connected to the VPS. When configuring the VPS 
via the Auto Configuration feature, this parameter is set automatically.
Default
None
*1The value range varies depending upon Country/Area and VPS model (KX-TVA50/KX-TVA200). Consult your dealer for more details. 
						

							2.5 System Parameters
154 Programming Manual
Va l u e  R a n g e
2–5 digits
Feature Manual References
2.4.1 Auto Configuration (APT/DPT Integration Only)
Operator Transfer Sequence
Specifies the sequence for transferring calls to an operators extension.
Default
FX
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , # and special codes
D: Disconnecting
F: Hook Flash
R: Ringback Tone Detection
T: Dial Tone Detection
,: Dial Pause (default 1 s)
;: Dial Pause (default 3 s)
X: Extension Dialing
0–9, , #: Dial Code
Extension Transfer Sequence
Specifies the sequence for transferring calls to any extension except an operators extension.
Default
FX
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , # and special codes
D: Disconnecting
F: Hook Flash
R: Ringback Tone Detection
T: Dial Tone Detection
,: Dial Pause (default 1 s)
;: Dial Pause (default 3 s)
X: Extension Dialing
0–9, , #: Dial Code
Alternate Extension Transfer Sequence
Specifies the sequence for transferring calls to extensions in the Alternate Extension Group. 
						

							2.5 System Parameters
Programming Manual 155
Default
FX
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , # and special codes
D: Disconnecting
F: Hook Flash
R: Ringback Tone Detection
T: Dial Tone Detection
,: Dial Pause (default 1 s)
;: Dial Pause (default 3 s)
X: Extension Dialing
0–9, , #: Dial Code
Feature Manual References
2.2.1 Alternate Extension Group
Reconnect Sequence on Busy
Specifies the sequence for reconnecting to the caller if the called extension is busy.
Default
F
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , # and special codes
D: Disconnecting
F: Hook Flash
R: Ringback Tone Detection
T: Dial Tone Detection
,: Dial Pause (default 1 s)
;: Dial Pause (default 3 s)
X: Extension Dialing
0–9, , #: Dial Code
Reconnect Sequence on No Answer
Specifies the sequence for reconnecting to the caller if the called extension does not answer.
Default
F
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , # and special codes
D: Disconnecting
F: Hook Flash 
						

							2.5 System Parameters
156 Programming Manual
R: Ringback Tone Detection
T: Dial Tone Detection
,: Dial Pause (default 1 s)
;: Dial Pause (default 3 s)
X: Extension Dialing
0–9, , #: Dial Code
Reconnect Sequence on Refuse Call
Specifies the sequence for retrieving a call placed on hold after the extension (in Call Screening 
mode) has refused to accept it.
Default
F
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , # and special codes
D: Disconnecting
F: Hook Flash
R: Ringback Tone Detection
T: Dial Tone Detection
,: Dial Pause (default 1 s)
;: Dial Pause (default 3 s)
X: Extension Dialing
0–9, , #: Dial Code
Light-On Sequence for Message Waiting Lamp
Specifies the sequence for turning on the Message Waiting Lamp at an extension.
Default
None
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , # and special codes
D: Disconnecting
F: Hook Flash
R: Ringback Tone Detection
T: Dial Tone Detection
,: Dial Pause (default 1 s)
;: Dial Pause (default 3 s)
X: Extension Dialing
0–9, , #: Dial Code
Feature Manual References
2.2.32 Message Waiting Notification—Lamp 
						

							2.5 System Parameters
Programming Manual 157
Light-Off Sequence for Message Waiting Lamp
Specifies the sequence for turning off the Message Waiting Lamp at an extension.
Default
None
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , # and special codes
D: Disconnecting
F: Hook Flash
R: Ringback Tone Detection
T: Dial Tone Detection
,: Dial Pause (default 1 s)
;: Dial Pause (default 3 s)
X: Extension Dialing
0–9, , #: Dial Code
Feature Manual References
2.2.32 Message Waiting Notification—Lamp
Message Waiting Lamp Retry Time
Specifies the number of times the VPS will retry turning on/off the Message Waiting Lamp of an 
extension. This parameter is enabled only when the integration mode is None or Inband mode.
Default
2
Va l u e  R a n g e
0–5 times
Feature Manual References
2.2.32 Message Waiting Notification—Lamp
Message Waiting Lamp Interval Time
Specifies the time between retries when the VPS retires turning on/off the Message Waiting Lamp of 
an extension. This parameter is enabled only when the integration mode is None or Inband mode.
Default
1
Va l u e  R a n g e
1 min–60 min
Feature Manual References
2.2.32 Message Waiting Notification—Lamp 
						

							2.5 System Parameters
158 Programming Manual
Call Waiting Sequence
Specifies the sequence for performing Call Waiting if the called extension is busy.
Default
1
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , # and special codes
D: Disconnecting
F: Hook Flash
R: Ringback Tone Detection
T: Dial Tone Detection
,: Dial Pause (default 1 s)
;: Dial Pause (default 3 s)
X: Extension Dialing
0–9, , #: Dial Code
Release Sequence for Call Waiting
Specifies the sequence for releasing Call Waiting.
Default
F
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , # and special codes
D: Disconnecting
F: Hook Flash
R: Ringback Tone Detection
T: Dial Tone Detection
,: Dial Pause (default 1 s)
;: Dial Pause (default 3 s)
X: Extension Dialing
0–9, , #: Dial Code
Receiving Caller ID
Enables or disables the VPS to receive Caller ID from the PBX while receiving a call.
Default
Enable
Va l u e  R a n g e
Disable, Enable 
						

							2.5 System Parameters
Programming Manual 159
Waiting Time for Receiving Caller ID
Specifies the length of time that the VPS waits before receiving Caller ID from the PBX. This 
parameter is needed only when Enable is selected in Receiving Caller ID.
Default
0 s
Va l u e  R a n g e
0 s–10 s
Inband Signaling
Set these parameters only if the Integration Mode is set to Inband under PBX Environment. If the 
PBX type is set to a KX-T series PBX, the Inband Signaling parameters will be automatically set to 
the default codes for the KX-T series PBX.
Note
 Default values below vary depending on the setting of PBX type in PBX Environment.
Ringback
Specifies the DTMF signal used to indicate a ringback tone. Sent to the VPS when the extension 
dialed is ringing.
Default
1
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , #, and A–D
Busy
Specifies the DTMF signal used to indicate a busy tone. Sent to the VPS when the called extension 
is ringing.
Default
2
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , #, and A–D
Reorder
Specifies the DTMF signal used to indicate a reorder tone. Sent to the VPS when the VPS dials an 
invalid extension number or when the VPS dials a port number of the PBX that is connected to the 
VPS (i.e., the VPS calls itself).
Default
3 
						

							2.5 System Parameters
160 Programming Manual
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , #, and A–D
DND
Specifies the DTMF signal used to indicate a Do Not Disturb tone. Sent to the VPS when the dialed 
extension is in Do Not Disturb mode.
Default
4
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , #, and A–D
Answer
Sent to the VPS when the called extension answers the call.
Default
5
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , #, and A–D
Forward to VM Ringing
Specifies the DTMF signal used to indicate a Forward to VM Ring tone. Sent to the VPS when the 
dialed extension has set calls to be forwarded to the VPS and a VPS port is available to handle the 
call.
Default
6
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , #, and A–D
Forward to VM Busy
Specifies the DTMF signal used to indicate a Forward to VM Busy tone. Sent to the VPS when the 
dialed extension has set calls to be forwarded to the VPS but no VPS ports are available to handle 
the call.
Default
7
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , #, and A–D