NEC Neax 2400 Imx Installation Manual

							NDA-24234 CHAPTER 4
Page 291
Revision 3.0
SYSTEM STARTUP
Procedure for Program Install consists of the following items.
Note:The control of 7-seg LED is the next page.(Case of program install and restart processing)
NAP-200-020
Sheet 1/6
Program Install and Load
ATTENTIONContents
Static Sensitive
Handling
Precautions Required
Generic Software 2 ~ 11
Internal MAT Software 1 - 2
TCP/IP Software 1 Install
Application
Software Install
HD Initial
Off-Line Star t Up
Refer to (a) Procedure for Off-Line Star t Up
Refer to (b) Procedure for HD Initial
HD format
Generic Software (1) Install
Making Directory in the HD
Refer to (d) Procedure for Application Software Install START
ENDRefer to (c) Procedure for Basic Software Install 
						

							CHAPTER 4 NDA-24234
Page 292
Revision 3.0
SYSTEM STARTUP
(a) Procedure for off-line start-up
NAP-200-020
Sheet 2/6
Program Install and Load
Status change of 7 Segment LED on the EMA card
ATTENTIONContents
Static Sensitive
Handling
Precautions Required
START
END
Set the SENSE switch
to “c” on the CPU Front Panel.
 Push the CPURST 
  button on the CPU
  Front Panel. 
 
              or 
 
 Turn Power-SW ON.
Star tup  
end (off-line mode) 
for the system to be
initialized (CPU0, CPU1)  
						

							NDA-24234 CHAPTER 4
Page 293
Revision 3.0
SYSTEM STARTUP
(b) Procedure for HD Initial
NAP-200-020
Sheet 3/6
Program Install and Load
Status change of 7 Segment LED on the CPU Front 
Panel.
Note:
ATTENTIONContents
Static Sensitive
Handling
Precautions Required
START
END
 HD Format
Set the SENSE switch for the
system to be initialized (CPU0,
CPU1) to “1” on the CPU Front
Panel.
Insert the FD Basic Generic
Disk 1 into the FDD.
Flip the MBR key on the CPU
Front Panel [OFF-ON-OFF].
Display end 
SENS SW 7SEG LED FUNCTION
1FORMAT → COPY → MAKING DIRECTORY →
 
 →
  
						

							CHAPTER 4 NDA-24234
Page 294
Revision 3.0
SYSTEM STARTUP
(c) Procedure for Generic Software (#2 ~ #11) Internal MAT Software (1 ~ 2), TCP/
IP Software (1) Install
NAP-200-020
Sheet 4/6
Program Install and Load
Status change of 7 Segment LED on the CPU Front 
Panel.
WARNING:Removal or Make Busy of the HFD card is
not allowed while the Floppy Disk or Hard
Disk is being accessed.
ATTENTIONContents
Static Sensitive
Handling
Precautions Required
START
END* Repeat
Inser t the FD Basic Generic 
Disk 2 into the FDD.
*
Set the SENSE switch
to “3” on the CPU Front Panel. for the system to have
DATA installed (CPU0, CPU1) 
Flip the MBR key on the 
CPU Front Panel card 
OFF–ON–OFF.
  Generic Software 3 ~ 11
   Internal MAT Software 1 ~ 2
   TCP/IP Software 1
   
						

							NDA-24234 CHAPTER 4
Page 295
Revision 3.0
SYSTEM STARTUP
(d) Procedure for Application Software Install
NAP-200-020
Sheet 5/6
Program Install and Load
Status change of 7 Segment LED on the CPU Front 
Panel. 
WARNING:Removal or Make Busy of the HFD card is
not allowed while the Floppy Disk or Hard
Disk is being accessed.
ATTENTIONContents
Static Sensitive
Handling
Precautions Required
Inser t the FD “Application 
Software into the FDD. START
END
Flip the MBR Key on the 
CPU Front Panel
Set the SENSE switch
to “3” on the CPU Front Panel. for the system to have DATA
installed (CPU0, CPU1) 
[OFF–ON–OFF].
INSTALL END  
						

							CHAPTER 4 NDA-24234
Page 296
Revision 3.0
SYSTEM STARTUP
Procedure for  Program Load
This section describes system start-up procedure in which a program is loaded from the HD to the MEM
and the data memory is cleared.
NAP-200-020
Sheet 6/6
Program Install and Load
START
Program Load Set the SENSE switch to “1” (restart with data 
memory clear) on the CPU Front Panel and press the 
CPURST button.
The system is initialized when LOADING from the 
HD to the MEM is completed.
Verify that the OPE lamp on the CPU Front Panel 
starts flashing.
Set On-Line mode Set the SENSE switch to “2” (restart without data 
memory clear) on the CPU Front Panel.
END
ATTENTIONContents
Static Sensitive
Handling
Precautions Required 
						

							NDA-24234 CHAPTER 4
Page 297
Revision 3.0
SYSTEM STARTUP
NAP-200-021
Sheet 1/2
Assignment of Office Data
START
Start up the MAT
Enter  basic  data Assign the following data via the MAT per the office data 
programming sheet.
“AT I M”: Assignment of Date and Time
“ASYD” (SYS 1, 2, & 3) /ASYDL (SYS 1 & 2): 
System Data assignment
“AUNT”: Unit Data assignment
Save basic data Save the above data onto the hard disk (HD) using the 
“MEM_HDD” Command.
Initialize Make sure that the SENSE switch on the CPU Front 
Panel has been set to “2”.
Press the CPURST button on the CPU Front Panel.
Clear the alarm by pressing the ALM RST button on the 
TOPU.
Assign Office Data Assign data according to the office data programming 
sheet.
ATTENTIONContents
Static Sensitive
Handling
Precautions Required
A 
						

							CHAPTER 4 NDA-24234
Page 298
Revision 3.0
SYSTEM STARTUP
NAP-200-021
Sheet 2/2
Assignment of Office Data
Save Office Data onto HD Save the Office Data onto the hard disk (HD) from the 
MEM using the “MEM_HDD” command.
Save Office Data onto FD Save the Office Data onto a floppy disk (FD) from the 
HD using the “HDD_MAT” command.
END
ATTENTIONContents
Static Sensitive
Handling
Precautions Required
A 
						

							NDA-24234 CHAPTER 4
Page 299
Revision 3.0
SYSTEM STARTUP
NAP-200-022
Sheet 1/5
Check of Lamp Indications and System 
Messages
START
Check lamp indications on Line/ 
Trunk circuit cardsCheck lamp indications on each of the assigned Line/
Trunk circuit cards.
OPE lamp (G): ON
BL lamp (R): OFF
If the lamp indications are other than above, investigate 
per Chapter 6: “FAULT RECOVERY DURING 
TESTS.”
Check lamp indications on control 
system circuit cardsThe OPE lamps (G) are shown in Figure 022-1 through 
Figure 022-4.
If any alarm lamp illuminates, check switch settings on 
the circuit card, mounting positions of the cards within 
that module, control cable connections (Front & 
Backplane), and Office Data assignments.
Confirm that no alarm lamps (R) / (Y) 
are illuminating on the TOPUFor explanations of the TOPU (Top Unit) lamp 
indications, refer to the System Operations and 
Maintenance Manual.
Check System Messages Display System Messages using MAT command 
“DFTD.”
END
If a System Message which indicates a fault is displayed, 
investigate and recover the fault referring to the System 
Operations and Maintenance Manual.
START
ATTENTIONContents
Static Sensitive
Handling
Precautions Required 
						

							CHAPTER 4 NDA-24234
Page 300
Revision 3.0
SYSTEM STARTUP
Figure 022-1  LED Indications in Normal Operation (Single IMG Configuration)
13 14
MUX ACT
MUX(PH-PC36) MUX(PH-PC36)
13 14
MUX ACT
MUX(PH-PC36) MUX(PH-PC36)
13 14
MUX ACT
MUX(PH-PC36) MUX(PH-PC36)
13 14
TSW ACT
MUX ACT
PLO ACT
TSW(PH-SW10) TSW(PH-SW10)
03 04
IOC(PH-IO24) EMA(PH-PC40)
OPE OPE/MB
TO P U
PIM3
PIM2
PIM1
PIM0
LPR
BASEUFA N U
BSCM
FRONT VIEW
: Lamp is ON (Green) : Lamp is OFF: Lamp is Flashing (Green) Legend CPU 0 -) ACT
TSW 0 -) ACT
PLO 0 -) ACT System State
CPU OPEIMG0
IMG1 DSP 1 (PZ-DK224)
DSP 0 (PZ-DK224)CPU OPE
FRONTTSW 
TSW ACT
MUX ACT
PLO ACT
MB
TSW MBR
PLO MBR
FRONTMUX
MUX ACT
MB
This figure shows the LED indications for a fully expanded system as an example.