NEC Neax 2400 Imx Installation Manual
Have a look at the manual NEC Neax 2400 Imx Installation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NDA-24234 CHAPTER 3 Page 241 Revision 3.0 INSTALLATION PROCEDURE Figure 016-7 Mounting of Handset (Left Side of DESK CONSOLE) (Continued) NAP-200-016 Sheet 12/41 Installation of the DESK CONSOLE and Cable Connection Mount the Handset Support to DESK CONSOLE with 3 screws as shown below. Handset Supportprojection projection
CHAPTER 3 NDA-24234 Pag e 24 2 Revision 3.0 INSTALLATION PROCEDURE (b) When mounting at the right side of DESK CONSOLE Figure 016-8 Mounting of Handset (Right Side of DESK CONSOLE) NAP-200-016 Sheet 13/41 Installation of the DESK CONSOLE and Cable Connection Screw (1) Screw (1) Screw (5) Screw (5) Screw (4) Screw (4) Screw (3) Screw (3)Screw (2) Screw (2)Handset Metal Plate Metal PlateHandset When mounting at the left side When mounting at the right sideTurn over the metal plate. DESK CONSOLE Hole Handset code (DESK CONSOLE side)(Handset side) Side View 2. Put the Handset code through the hole as shown below. 1. Remove the metal plate from the Handset, turn it over, and mount it to the Handset again. Refer to the figure below.
NDA-24234 CHAPTER 3 Page 243 Revision 3.0 INSTALLATION PROCEDURE Figure 016-8 Mounting of Handset (Right Side of DESK CONSOLE) (Continued) NAP-200-016 Sheet 14/41 Installation of the DESK CONSOLE and Cable Connection 3. Connect the Handset code to HAND H/S0 connector as shown below (H/S1 is not used for the Handset). Bottom View of DESK CONSOLE Bottom view Top View Code HAND H/S0 H/S1
CHAPTER 3 NDA-24234 Pag e 24 4 Revision 3.0 INSTALLATION PROCEDURE Figure 016-8 Mounting of Handset (Right Side of DESK CONSOLE) (Continued) NAP-200-016 Sheet 15/41 Installation of the DESK CONSOLE and Cable Connection Mount the Handset Support to DESK CONSOLE with 3 screws as shown below. Handset Support projection projection
NDA-24234 CHAPTER 3 Page 245 Revision 3.0 INSTALLATION PROCEDURE 5. CONNECTION OF RECORDING EQUIPMENT The following are required for using recording function: The RECC circuit card Recording Equipment 8-core Line Cable Rosette An RECC card (PA-M87) connects DESK CONSOLEs and recording equipment in the following combinations: Six DESK CONSOLEs and one recording equipment × 1 set Three DESK CONSOLEs and one recording equipment × 2 set Figure 016-9 RECC Card Cable Connection Diagram NAP-200-016 Sheet 16/41 Installation of the DESK CONSOLE and Cable Connection 50FLT-CHAMP CABLE Note 1:Recording equipment is positioned between the C.O. line and telephones. Note 2:One recording equipment can be shared with multiple RECC cards. Note 3:When sharing one recording equipment with multiple RECC cards, multiple connection of ZA and ZB terminals is required. R E C C DESK CONSOLEMDFInstallation Cable8-core Line CablePIM RECC card FrontRecording Equipment8-pin Modular Connector 8-core Line CableRosette MDF A B LA LB KA KB A0 B0 M0A M0B K0A K0B L0A L0B T0A T0B ZA ZB L0B T0A T0B ZA ZB Note 1 Note 3 Circuit Card Front Connector PIM Telephone side leads Note 1C.O. line side leads8-pin Modular Connector Note 2L0A Rosette Recording Equipment R E C C PIM Bottom View of DESK CONSOLE REC
CHAPTER 3 NDA-24234 Pag e 24 6 Revision 3.0 INSTALLATION PROCEDURE (a) When using three DESK CONSOLEs and one recorderNote 1 Note 1: Switch settings of SW10, SW12 and SW13 on the PA-M87 card are required. For switch setting and connec- tor lead accommodation, refer to the NEAX2400 IMX Circuit Card Manual. Figure 016-10 Three DESK CONSOLEs and One Recording Equipment NAP-200-016 Sheet 17/41 Installation of the DESK CONSOLE and Cable Connection Note 2:Refer to Figure 016-9“RECC Card Cable Connection Diagram” for cable connection. Note 3:Connections of Circuit 1 through 5 are the same as those of Circuit 0. Note 4:Recording equipment is positioned between the C.O. line and telephones. DESK CONSOLE Note 2 MDF Note 2 PIM RECC card Circuit 0 Note 3 Front Connector A B LA LB KA KB A0 B0 M0A M0B K0A K0B Circuit 1 Circuit 2 L0A L0B T0A T0B Circuit 3 Circuit 4 Circuit 5 L1A L1B T1A T1B C.O. line side leads Telephone side leads Recording Equipment Recording Equipment Note 4 Note 4 C.O. line side leads Telephone side leads Note 4 Note 4
NDA-24234 CHAPTER 3 Page 247 Revision 3.0 INSTALLATION PROCEDURE (b) When using six DESK CONSOLEs and one recording equipmentNote 1 Note 1: Switch settings of SW10, SW12 and SW13 on the PA-M87 card are required. For switch setting and connec- tor lead accommodation, refer to the NEAX2400 IMX Circuit Card Manual. Figure 016-11 Six DESK CONSOLEs and One Recording Equipment NAP-200-016 Sheet 18/41 Installation of the DESK CONSOLE and Cable Connection Note 2:Refer to Figure 016-9 “RECC Card Cable Connection Diagram” for cable connection. Note 3:Connections of Circuit 1 through 5 are the same as those of Circuit 0. Note 4:Recording equipment is positioned between the C.O. line and telephones. DESK CONSOLE Note 2 MDF A B LA LB KA KB A0 B0 M0A M0B K0A K0B Circuit 1 Circuit 2 Circuit 3 Circuit 4 Circuit 5 L0A L0B T0A T0B Recording EquipmentC.O. line side leads Telephone side leads PIM Front Connector RECC cardNote 2 Circuit 0 Note 4 Note 4 Note 3
CHAPTER 3 NDA-24234 Pag e 24 8 Revision 3.0 INSTALLATION PROCEDURE 6. 8-CORE LINE CABLE (INSTALLATION CABLE) Figure 016-12 8-core Line Cable NAP-200-016 Sheet 19/41 Installation of the DESK CONSOLE and Cable Connection Note 1:Cut the cable in proper length. Attach the modular connector to both sides of the 8-core line ca- ble using installation tool. Note 2:Be sure to check the polarity of pin numbers 7 (LA) (+) and 8 (LB) (–). Speech Speech Not used Not used Recording Start Signal (Relay Contact) Recording Start Signal (Relay Contact) Recording Lamp Signal (+) Recording Lamp Signal (–)A B – – KA KB LA ( Note 2) LB ( Note 2)1 2 3 4 5 6 7 8 8-pin Modular Connector (Rosette side) 8-pin Modular Connector (DESK CONSOLE side) Note 1 8-core Line Cable (Installation Cable) Pin No. 12345678 LEAD NAMEMEANING Pin No.
NDA-24234 CHAPTER 3 Page 249 Revision 3.0 INSTALLATION PROCEDURE 7. CONNECTION OF AC-DC ADAPTER (OPTIONAL) The AC-DC adapter is required when the power supply from the distant PBX is not available. Figure 016-13 Connection of AC-DC Adapter NAP-200-016 Sheet 20/41 Installation of the DESK CONSOLE and Cable Connection The connector for the AC-DC adapter is on the rear side of DESK CONSOLE. AC-DC Adapter ( )
CHAPTER 3 NDA-24234 Pag e 25 0 Revision 3.0 INSTALLATION PROCEDURE 8. MOUNTING OF ADD-ON CONSOLE (FOR HOTEL SYSTEM) ADD-ON CONSOLE is used in the Hotel System. 1. Cable Connection Diagram (a) Cable Connection Diagram of Add-On Console (When the power is supplied from the PBX) Figure 016-14 Add-On Console Cable Connection Diagram (When the Power Is Supplied from the PBX) NAP-200-016 Sheet 21/41 Installation of the DESK CONSOLE and Cable Connection GND GND A1 B1 BN4810 BN4811 A1 B1 GND GND A0 B0 A0 bc M aPBX AT IMDFIDFInstallation Cable B0 BN4800 BN4801 (–48V) (–48V) BN4800 BN4801 BN4810 BN4811 RPT1 ADD-ON CONSOLE6-core Modular Rosette 6-core Modular RosetteADD-ON CONSOLE 6-core Modular Cable 6-core Modular Cable