NEC Neax 2400 Imx Installation Manual
Have a look at the manual NEC Neax 2400 Imx Installation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NDA-24234 CHAPTER 3 Page 141 Revision 3.0 INSTALLATION PROCEDURE Figure 010-25 Details on Bus Cable Connections (for 2-PIM System) (Single IMG Configuration) NAP-200-010 Sheet 46/71 Internal Cable Connections Connect the bus cables as shown below. Note that dotted lines indicate bus cables for a dual system. REAR VIEWFRONT VIEW TO P U PIM 1 (PIM 0) BSCM (LPM) (BASEU)PIM 1 BSCM (BASEU) (LPM) (1)(2)(3) (4)(5) (6) (7)(8)(9) (10) (11) (PIM 0) ALMA ALMB MUSIC0 ALMA BUS1A BUS0A MUSIC DSP ALMKEY BUS1BUS0 PC 19 GT 16 CN AB MUX3 MUX2 MUX1 MUXPC 19 CN CN CNCN CNGT 16 A B MUX3 MUX2MUX1 MUX KEYDSPM 13 14 13 14 00 01 02 03 04 05 06 00 01 02 03 04 05 06
CHAPTER 3 NDA-24234 Page 142 Revision 3.0 INSTALLATION PROCEDURE NAP-200-010 Sheet 47/71 Internal Cable Connections Table 010-16 Bus Cable Connections for 2-PIM System (Single IMG Configuration) No.FROM TO CABLE NAME REMARKS UNIT/MODULECONNECTOR NAMEUNIT/ MODULECONNECTOR NAME 1LPRCN-B (Front Connector)PIM0 BUS0A 50-40 GT BUS CA-A 2LPRCN-A (Front Connector)LPR BUS0 EXGT BUS CA-A 3 LPR KEY TOPU KEY 10AL-(260) FLT CA 4 LPR ALM PIM0 ALMA 20AL-(60) FLT CA 5 LPR (GT 16)CN-A (Front Connector)LPR BUS1 EXGT BUS CA-A 6 LPR (GT 16)CN-B (Front Connector)PIM0 BUS1A 50-40 GT BUS CA-A 7 LPR DSP TOPU DSPM 20AL-(270) FLT CA 8 LPR MUSIC PIM0 MUSIC0 16PH MOH CA (1) 9 PIM0 MUX1 PIM1 MUX MT24 TSW CA-90 10 PIM0 MUX1 PIM1 MUX MT24 TSW CA-90 11 PIM0 ALMB PIM1 ALMA 20AL-(10) FLT CA
NDA-24234 CHAPTER 3 Page 143 Revision 3.0 INSTALLATION PROCEDURE Run the bus cables, referring to Figure 010-27. Then, fasten the cables to the cabinet, referring to Figure 010-26. Figure 010-26 Bus Cable Connections for 3-PIM System (Single IMG Configuration) NAP-200-010 Sheet 48/71 Internal Cable Connections The drawing below illustrates how to run the bus cables for the 3-PIM system. For details on actual cable runnings, see Figure 010-27. Note:Normally, the cables are fastened onto the cabinet at the proposed locations, where small dots () are pro- vided in this figure. BackplaneBackplaneBackplane
CHAPTER 3 NDA-24234 Page 144 Revision 3.0 INSTALLATION PROCEDURE Figure 010-27 Details on Bus Cable Connections (for 3-PIM System) (Single IMG Configuration) NAP-200-010 Sheet 49/71 Internal Cable Connections Connect the bus cables as shown below. Note that dotted lines indicate bus cables for a dual system. 00 01 02 03 04 05 06 BUS0A KEY ALM ALMA ALMB MUSIC0 MUSIC DSP (1) (3) (5) (8) (7) (10) (12) (13) (14) (2) (4) (6) PIM 1 PIM 1 FA N UFA N U PIM 2PIM 2 TO P UFRONT VIEW REAR VIEW PC 19 GT 16 GT 16 AB A B MUX1 MUX1 MUX2 MUX2 MUX3 MUX3 MUX MUX CN CN CN CN BUS 0 BUS 1 1313 1414 MUX MUX 1314 KEY DSPM (9) (11) BUS1A ALMA ALMB ALMA (BASEU)(BASEU)(PIM 0) (LPM) BSCM(PIM 0) (LPM) BSCM CN CN PC 19 00 01 02 03 04 05 06
NDA-24234 CHAPTER 3 Page 145 Revision 3.0 INSTALLATION PROCEDURE NAP-200-010 Sheet 50/71 Internal Cable Connections Table 010-17 Bus Cable Connections for 3-PIM System (Single IMG Configuration) No.FROM TO CABLE NAME REMARKS UNIT/MODULECONNECTOR NAMEUNIT/ MODULECONNECTOR NAME 1 LPRCN-B (Front Connector)PIM0 BUS0A 50-40 GT BUS CA-A 2 LPR CN-A (Front Connector)LPR BUS0 EXGT BUS CA-A 3 LPR KEY TOPU KEY 10AL-(260) FLT CA 4 LPR ALM PIM0 ALMA 20AL-(60) FLT CA 5 LPR (GT 16)CN-A (Front Connector)LPR BUS1 EXGT BUS CA-A 6 LPR (GT 16)CN-B (Front Connector)PIM0 BUS1A 50-40 GT BUS CA-A 7 LPR DSP TOPU DSPM 20AL-(270) FLT CA 8 LPR MUSIC PIM0 MUSIC0 16PH MOH CA (1) 9 PIM0 MUX1 PIM1 MUX MT24 TSW CA-90 10 PIM0 MUX2 PIM2 MUX MT24 TSW CA-140 11 PIM0 MUX1 PIM1 MUX MT24 TSW CA-90 12 PIM0 MUX2 PIM2 MUX MT24 TSW CA-140 13 PIM0 ALMB PIM1 ALMA 20AL-(10) FLT CA 14 PIM1 ALMB PIM2 ALMA 20AL-(20) FLT CA
CHAPTER 3 NDA-24234 Page 146 Revision 3.0 INSTALLATION PROCEDURE Run the bus cables, referring to Figure 010-29. Then, fasten the cables to the cabinet, referring to Figure 010-28. Figure 010-28 Bus Cable Connections for 4-PIM System (Single IMG Configuration) NAP-200-010 Sheet 51/71 Internal Cable Connections The drawing below illustrates how to run the bus cables for the 3-PIM system. For details on actual cable runnings, see Figure 010-29. Note:Normally, the cables are fastened onto the cabinet at the proposed locations, where small dots () are pro- vided in this figure. Backplane BackplaneBackplane Backplane
NDA-24234 CHAPTER 3 Page 147 Revision 3.0 INSTALLATION PROCEDURE Figure 010-29 Details on Bus Cable Connections (for 4-PIM System) (Single IMG Configuration) NAP-200-010 Sheet 52/71 Internal Cable Connections Connect the bus cables as shown below. Note that dotted-lines indicate bus cables for a dual-system. CN CN GT16 ABCN CN 1314 13 14 00 01 02 03 04 05 06 ALMB ALMA MUSIC0 MUSIC (1) (3) (5) (8) (7) (10) (13) (14) (15)(17) (16) (11) (2) (4)(6) (BASEU) (LPM) (PIM 0)(PIM 0) PIM 1 PIM 1 FA N UFA N U PIM 2PIM 2 PIM 3PIM 3 TOPUTOPU FRONT VIEW REAR VIEW PC19 PC19 GT16 AB 1314 13 14KEY (9)(12) BSCMBSCM (LPM) BUS0A ALMA BUS1A BUS 0 BUS 1 ALMB ALMA ALMA ALMB KEY ALM DSP DSPM MUX MUX MUX MUX MUX MUX MUX1MUX1 MUX2 MUX2 MUX3 MUX3 00 01 02 03 04 05 06 CN CN
CHAPTER 3 NDA-24234 Page 148 Revision 3.0 INSTALLATION PROCEDURE NAP-200-010 Sheet 53/71 Internal Cable Connections Table 010-18 Bus Cable Connections for 4-PIM System (Single IMG Configuration) No.FROM TO CABLE NAME REMARKS UNIT/ MODULECONNECTOR NAMEUNIT/ MODULECONNECTOR NAME 1 LPRCN-B (Front Connector)PIM0 BUS0A 50-40 GT BUS CA-A 2 LPR CN-A (Front Connector)LPR BUS0 EXGT BUS CA-A 3 LPR KEY TOPU KEY 10AL-(260) FLT CA 4 LPR ALM PIM0 ALMA 20AL-(60) FLT CA 5 LPR (GT 16)CN-A (Front Connector)LPR BUS1 EXGT BUS CA-A 6 LPR (GT 16)CN-B (Front Connector)PIM0 BUS1A 50-40 GT BUS CA-A 7 LPR DSP TOPU DSPM 20AL-(270) FLT CA 8 LPR MUSIC PIM0 MUSIC0 16PH MOH CA (1) 9 PIM0 MUX1 PIM1 MUX MT24 TSW CA-90 10 PIM0 MUX2 PIM2 MUX MT24 TSW CA-140 11 PIM0 MUX3 PIM3 MUX MT24 TSW CA-180 12 PIM0 MUX1 PIM1 MUX MT24 TSW CA-90 13 PIM0 MUX2 PIM2 MUX MT24 TSW CA-140 14 PIM0 MUX3 PIM3 MUX MT24 TSW CA-180 15 PIM0 ALMB PIM1 ALMA 20AL-(10) FLT CA 16 PIM1 ALMB PIM2 ALMA 20AL-(20) FLT CA 17 PIM2 ALMB PIM3 ALMA 20AL-(10) FLT CA
NDA-24234 CHAPTER 3 Page 149 Revision 3.0 INSTALLATION PROCEDURE Figure 010-30 Internal Bus Cable Connection for IMG0 (Multiple IMG Configuration) NAP-200-010 Sheet 54/71 Internal Cable Connections BUS 0 BUS 1 DSP KEY 00 01 02 03 04 05 06 00 01 02 03 04 05 06 (3) (2) (5) (6) (8) (7) (1) (4) BASEU BASEU PIM 0PIM 0 PIM 1PIM 1 FA N UFA N U PIM 2PIM 2 PIM 3PIM 3 TOPUTOPU FRONT VIEW REAR VIEW PC 19 PC 19 GT13 GT 13 M T M T CN LPM LPR DSP KEY CN CN CN CN CN ALMA ALM ALMA ALMB ALMA ALMB ALMB ALMA
CHAPTER 3 NDA-24234 Page 150 Revision 3.0 INSTALLATION PROCEDURE NAP-200-010 Sheet 55/71 Internal Cable Connections Table 010-19 Internal Bus Cable Connection for IMG0 (Multiple IMG Configuration) No.FROM TO CABLE NAME REMARKS UNIT/MODULECONNECTOR NAMEUNIT/ MODULECONNECTOR NAME 1 LPM (CPU0) CN-M LPM BUS0 EXGT BUS CA-A 2 LPM (CPU1) CN-M LPM BUS1 EXGT BUS CA-A 3 LPM KEY TOPU KEY 10AL-(260) FLT CA 4 LPM ALM PIM0 ALMA 20AL-(60) FLT CA 5 LPM DSP TOPU DSPL 20AL-(270) FLT CA 6 PIM0 ALMB PIM1 ALMA 20AL-(10) FLT CA 7 PIM1 ALMB PIM2 ALMA 20AL-(20) FLT CA 8 PIM2 ALMB PIM3 ALMA 20AL-(10) FLT CA