NEC Infoset 408 System Manual
Have a look at the manual NEC Infoset 408 System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
InfoSet 408Issue 1A System Manual4 - 19 13. Attach the WMU-U Unit to the posts on the wall plate (user-provided). Place the user-provided screws in the nodes on the WMU-U Unit and secure the WMU-U Unit to the wall. 14. Connect the line cord to the telephone. 15. With the WMU-U Unit attached to the wall, hook the two bottom tabs on the WMU-U Mount Unit into the tab slots on the telephone. Then push the two top tabs on the WMU-U Unit into the tab slots on the telephone. If the adapter has a power supply, lead the AC adapter cord out through the opening at the bottom of the telephone. Figure 4-25 Attaching the WMU-U Unit to the Wall Figure 4-26 Attaching the Telephone to the WMU-U Unit Posts Nodes Nodes Wal l WMU-U Unit Ta b S l o t s Telephone Adapter
Issue 1AInfoSet 408 4 - 20Telephones 2.3 Wall Mounting Single Line Telephones The DTP-1-1 TEL and DTP-1HM-1 TEL can be wall mounted. 1. Remove the hook from the unit. 2. Turn the hook over (back to the front) with the tab toward the top. 3. Slide the hook on its glides back down into position forming the hanger hook for the handset. Figure 4-27 Removing the Hook from a Single Line Telephone Figure 4-28 Turning the Hook Over Figure 4-29 Sliding the Hook into Position on a Single Line Telephone
InfoSet 408Issue 1A System Manual4 - 21 4. Unscrew the three screws on the unit to remove the plate. 5. Replace the plate and place the screws in the two positions indicated in the diagram. (The one remaining screw can be placed at the original third position.) Figure 4-30 Removing the Screws from the Base of a Single Line Telephone Figure 4-31 Replacing the Plate and Screws in the Base of the Single Line Telephone
Issue 1AInfoSet 408 4 - 22Telephones 6. Loosen the screws on the wall telephone plate. Leave the screws protruding enough to slip the telephone over the screws. 7. Mount the telephone onto the protruding screws by slipping the telephone over the screws as indicated in the diagram. Figure 4-32 Protruding Screws Figure 4-33 Mounting the Telephone
InfoSet 408Issue 1A System Manual4 - 23 SECTION 3 ADJUSTING THE HEIGHT OF TELEPHONES 3.1 Adjusting the Height of InfoSet Telephones The telephone stand can be used to prop the telephone at an angle. 1. Locate the telephone stand on the bottom of the telephone. 2. Pull the stand away from the telephone and pull up on the foot stand. Select the desired height level and snap the tabs on the foot stand into one of the two sets of grooves on the telephone stand. 3. If you want to return the telephone to the lowest position, pull the telephone stand away from the foot stand. Fold the foot stand down toward to base of the telephone and fold the telephone stand over the foot stand and snap it into place. Figure 4-34 Infoset Telephone Stand Figure 4-35 Adjusting the Height of the InfoSet Telephone Telephone Stand Lift foot stand and place into grooves
Issue 1AInfoSet 408 4 - 24Telephones 3.2 Adjusting the Height of the Electra Elite Telephones The base plate on Electra Elite telephones are hinged. The bottom portion can be adjusted up or down to raise or lower the height of the terminal. 1. Turn the telephone upside down and locate the tabs as shown in Figure 4-36 Locating the Adjustment Tabs on the Electra Elite Telephone. 2. Push the adjustment tabs and raise the base plate until it locks. Figure 4-36 Locating the Adjustment Tabs on the Electra Elite Telephone Figure 4-37 Raising the Base Plate on the Electra Elite Telephone
InfoSet 408Issue 1A System Manual4 - 25 3. The length of the cord can be adjusted by pulling the line cord though the groove in the bottom of the telephone. 4. To lower the base plate on the telephone, push on the adjustment tabs and push the base plate downward. Figure 4-38 Adjusting the Line Cord Length on the Electra Elite Telephone Figure 4-39 Lowering the Base Plate on the Electra Elite Telephone Ta b
Issue 1AInfoSet 408 4 - 26Telephones 3.3 Adjusting the LCD on the Electra Elite Display Telephones The adjustable Liquid Crystal Display (LCD) comes equipped on the display Electra Elite telephones. The LCD can be adjusted by pushing downward and upward as desired. Figure 4-40 Adjusting the LCD on the Electra Elite Telephone
InfoSet 408Issue 1A System Manual4 - 27 SECTION 4 INSTALLING LINE CARD LABELS AND PROTECTIVE PLASTIC PANELS ON T ELEPHONES 4.1 Installing the Line Card Labels and Protective Plastic Panel on the InfoSet Telephones A peel off label and protective plastic panel are provided with each telephone. The label helps identify the line keys and can be used to record the line key designations associated with each line key on the telephone. 1. Print or type the line key designations for the keys on the provided label. 2. Peel the label from the paper backing and place it over the telephone line keys. Be sure the protective plastic panel has been removed before attaching the sticky-backed label. Figure 4-41 Line Card Label for Infoset Telephones
Issue 1AInfoSet 408 4 - 28Telephones 3. If desired, peel the protective file from both sides of the protective plastic panel. 4. Locate two V-shaped tabs on each side of the lines keys on the face plate. Gently bend the panel and slip it under the tabs. If inserted properly, the panel will fit snugly against the face plate. Figure 4-42 Plastic Panel for InfoSet Telephones Figure 4-43 Installing the Plastic Cover on the InfoSet Telephone V-Shaped Ta b s V-Shaped Tables