Konica Minolta bizhub C451 User Manual

							Printing a user box document4
C4514-6
4.2 Printing
Available print settings
Settings can be specified for the following when a document is printed.
!
Detail 
The Fold/Bind settings are available only if optional finisher FS-608 is in-
stalled.
The Center Staple/Fold settings are available only if optional finisher FS-
519 is installed.
The Punch settings are available only if the punch kit is installed on the 
optional finisher.
For details on combining multiple documents and printing, refer to “Com-
bined printing” on page 4-64.
Available parametersDescriptionPage reference
Copies Specify the number of copies to be printed. p. 4-8
Print Select whether a single-sided or double-sided 
copy is to be printed.p. 4-9
Finishing Specify settings for collating, grouping, stapling, 
hole punching, folding/binding or center stapling/
folding.p. 4-9
Page Margin Print the document with a binding margin added. p. 4-15
Sheet/Cover/Chapter 
InsertPrint the document with other paper added as cov-
er sheets, insertions or chapter title pages.p. 4-18
Stamp/Composition Print the document with the date/time, page 
number or a stamp added.p. 4-30
Downloaded From ManualsPrinter.com Manuals 
						

							Printing a user box document4
C4514-7 To print a document
1From the Use Document screen, select the document to be printed.
2Under “Action”, touch [Print].
3Select the print settings.
Downloaded From ManualsPrinter.com Manuals 
						

							Printing a user box document4
C4514-8
4If desired, touch [Preview], then [Details] on the left side of the screen 
to check a preview image.
– For details on the Preview screen, refer to “Preview - Detail (Print/
Combine)” on page 2-78.
5Touch [Start], or press the [Start] key in the control panel.
!
Detail 
For details on changing the settings, refer to the descriptions starting with 
page 4-8.
Changing the number of copies
Specify the number of copies to be printed.
%In the Print screen, use the keypad to type in the desired number of 
copies.
– The number of copies can be set between 1 and 9,999.
– To reset the number of copies to “1”, press the [C] (clear) key.
Downloaded From ManualsPrinter.com Manuals 
						

							Printing a user box document4
C4514-9 Specifying single-sided/double-sided printing
Select whether a single-sided or double-sided copy of the document is to be 
printed.
%Touch [1-Sided] or [2-Sided].
Specifying Finishing settings
Specify settings for collating, grouping, stapling, hole punching, folding/
binding or center stapling/folding. Settings can be specified for the following.
ParameterDescription
Sort Select this setting to feed out copies of the document by sets.
Group Select this setting to feed out copies of the document by page.
Offset Select this setting to separate the sets or pages of the copies.
If a finisher is installed, the printed pages are fed out with each set 
shifted to separate it.
If no finisher is installed, the printed pages are fed out sorted in an 
alternating crisscross pattern.
Staple Select one of these settings to bind copies with a staple in the corner 
(upper left or upper right) or with two staples. The stapling position 
can also be selected.
Punch Select a setting to punch holes in copies. The position of the 
punched holes can also be selected.
Half-Fold (Center Staple/
Fold):Select this setting to fold copies in half before feeding them out.
Downloaded From ManualsPrinter.com Manuals 
						

							Printing a user box document4
C4514-10
!
Detail 
The feeding method when a finisher is installed can be changed from Ad-
ministrator mode. For details on the Finishing settings, refer to the User’s 
Guide [Copy Operations].
When a Fold/Bind or a Center Staple/Fold setting is selected, “Sort” is 
automatically selected, and the “Group”, Offset, Staple and Punch set-
tings are canceled.
2
Reminder 
In order to select a Fold/Bind or a Center Staple/Fold setting, all of the 
following conditions must be met.
The paper width must be between 7-3/16 and 12-1/4 inches on the North 
American (inch) model (between 182 and 314 mm on the European (met-
ric) model).
The paper length must be between 10-1/8 and 18 inches on the North 
American (inch) model (between 257 and 458 mm on the European (met-
ric) model).
In order to use a Fold/Bind setting, optional finisher FS-608 must be in-
stalled.
In order to use a Center Staple/Fold setting, optional finisher FS-519 
must be installed.
Center Staple (Center 
Staple/Fold):
Center Staple & Fold 
(Fold/Bind)Select this setting to staple copies at two places along the center be-
fore feeding them out.
Tri-Fold (Fold/Bind): Select this setting to fold copies in three before feeding them out.
ParameterDescription
Downloaded From ManualsPrinter.com Manuals 
						

							Printing a user box document4
C4514-11
1In the Print screen, touch [Finishing].
2Touch [Sort] or [Group]. To separate the copies, touch [Yes] under “Off-
set”.
– On the North American (inch) model:
– On the European (metric) model:
Downloaded From ManualsPrinter.com Manuals 
						

							Printing a user box document4
C4514-12
3Select the desired Staple and Punch settings.
– On the North American (inch) model:
– On the European (metric) model:
4To specify the positions of the staples and punched holes, touch [Po-
sition Setting].
5Touch the button for the desired position, and then touch [OK].
– When the “Corner” Staple setting is selected:
Downloaded From ManualsPrinter.com Manuals 
						

							Printing a user box document4
C4514-13 – When the “2 Position” Staple setting is selected:
– When a Punch setting is selected:
– On the North American (inch) model:
– On the European (metric) model:
6If finisher FS-608 is installed, touch [Fold/Bind]. If finisher FS-519 is in-
stalled, touch [Center Staple/Fold].
Downloaded From ManualsPrinter.com Manuals 
						

							Printing a user box document4
C4514-14
7If [Fold/Bind] was touched, touch [Yes], and then select the desired 
folding method.
8If [Center Staple/Fold] was touched, touch [Yes], and then select the 
desired folding method.
Downloaded From ManualsPrinter.com Manuals 
						

							Printing a user box document4
C4514-15 – To adjust the position of the center stapling and center fold, touch 
[Position Adjustment], and then specify an adjustment between -10 
and +10.
9Touch [OK], and then touch [OK] in the next screen that appears.
Adding a binding margin
A binding margin can be added to the left or right side or to the top of the 
printed pages. Settings can be specified for the following.
ParameterDescription
Margin Position Select the location where the binding margin is to be added. If “Au-
to” is selected, a binding margin along the long side of the paper is 
selected if the document length is less than 11-11/16 inches on the 
North American (inch) model (less than 297 mm on the European 
(metric) model). If the document length is more than 11-11/16 inches 
on the North American (inch) model (more than 297 mm on the Eu-
ropean (metric) model), a binding margin along the short side of the 
paper is selected.
Adjust Value An area with a width between 1/16 and 3/4 inches on the North 
American (inch) model (between 0.1 and 20.0 mm on the European 
(metric) model) can be specified. To specify a binding margin of 0 
mm, touch [None].
Image Shift When a binding margin is created, the image can be shifted accord-
ing to the position of the created binding margin. The image can be 
shifted between 1/16 and 10 inches on the North American (inch) 
model (between 0.1 and 250 mm on the European (metric) model) 
left, right, up or down, depending on the position of the binding mar-
gin. If the document is to be printed double-sided, touch [Change 
Back Shift] to also specify the shift on the back side of the pages.
Downloaded From ManualsPrinter.com Manuals