HP LaserJet M3035xs MFP User Manual

							Safety statements
Laser safety
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration has
implemented regulations for laser products m anufactured since August 1, 1976. Compliance is
mandatory for products marketed in the United States . The device is certified as a “Class 1” laser product
under the U.S. Department of Health and Human  Services (DHHS) Radiation Performance Standard
according to the Radiation Control for Health and Safety Act of 1968. Since radiation emitted inside the
device is completely conf ined within protective housings and external covers, the laser beam cannot
escape during any phase of  normal user operation.
WARNING!Using controls, making adjustments, or  performing procedures other than those
specified in this user guide may result in exposure to hazardous radiation.
Canadian DOC regulations
Complies with Canadian EMC Class A requirements.
« Conforme à la classe A des no rmes canadiennes de compatibilité électroma gnétiques. « CEM ». »
VCCI statement (Japan)
Power cord statement (Japan)
EMI statement (Korea)
ENWW Safety statements 229
 
						

							EMI statement (Taiwan)
Laser statement for Finland
Luokan 1 laserlaite
Klass 1 Laser Apparat
HP LaserJet M3027, M3027x, M3035, M3035xs, laserkirjoitin on käyttäjän kannalta turvallinen luokan
1 laserlaite. Normaalissa käytössä kirjoittimen suojakotelointi estää lasersäteen pääsyn laitteen
ulkopuolelle. Laitteen turvallisuusluokka on määritetty standardin EN 60825-1 (1994) mukaisesti.
VAROITUS !
Laitteen käyttäminen muulla kuin käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän
turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING !
Om apparaten används på annat sätt än i bruksanvisning specificerats, kan användaren utsättas för
osynlig laserstrålning, som överskrider gränsen för laserklass 1.
HUOLTO
HP LaserJet M3027, M3027x, M3035, M3035xs - kirjoittimen sisällä ei ole käyttäjän huollettavissa olevia
kohteita. Laitteen saa avata ja huoltaa ainoastaan sen huoltamiseen koulutettu henkilö. Tällaiseksi
huoltotoimenpiteeksi ei katsota väriainekasetin vaihtamista, paperiradan puhdistusta tai muita käyttäjän
käsikirjassa lueteltuja, käyttäjän tehtäväksi tarkoitettuja ylläpitotoimia, jotka voidaan suorittaa ilman
erikoistyökaluja.
VARO !
Mikäli kirjoittimen suojakotelo avataan, olet alttiina näkymättömällelasersäteilylle laitteen ollessa
toiminnassa. Älä katso säteeseen.
VARNING !
Om laserprinterns skyddshölje öppnas då apparaten är i funktion, utsättas användaren för osynlig
laserstrålning. Betrakta ej strålen. Tiedot laitteessa käytettävän laserdiodin säteilyominaisuuksista:
Aallonpituus 775-795 nm Teho 5 m W Luokan 3B laser.
230 Appendix D   Regulatory information ENWW
 
						

							E Working with memory and print servercards
This section explains the device memory  features and provides steps for expansion.
●
Overview
●
Install memory
●
Check DIMM installation
●
Save resources (permanent resources)
●
Enable memory for Windows
●
Use HP Jetdirect print server cards
ENWW 231
 
						

							Overview
One dual inline memory module (DIMM) slot is available for upgrading the device with the following
items:
● More memory—DIMMs are availabl
e in 64, 128, 256, and 512 MB.
● Other DIMM-based printer languages and printer options.
The device uses 100-pin 133 MHz DDR memory modu les. Extended data output (EDO) DIMMs are not
supported.
For ordering information, see 
Order parts, accessories, and supplies .
NOTESingle inline memory modules (SIMMs) used  in previous HP LaserJet printers are not
compatible with the device.
The device also has one EIO slot for expanding the de vice networking capabilities. The EIO slot can be
used to upgrade the device with an additional netw ork connection, such as a wireless print server,
network card, or a connectivity card for a serial or AppleTalk connection.
To find out how much memory is inst alled in the device, or to find out what is installed in the EIO slots,
print a configuration page. See 
Use information pages .
NOTEIf memory problems occur when you are pr inting complex graphics, you can make more
memory available by removing downloaded fonts,  style sheets, and macros from device memory.
Reducing the complexity of a print job from within a program can help avoid memory problems.
232 Appendix E   Working with memory and print server cards ENWW
 
						

							Install memory
You might want to add more memory to the device if you often print complex graphics, print PostScript
(PS) documents, or use many do wnloaded fonts. Added memory also give s you more flexibility in
supporting job-storage features, such as quick copying. 
Install device memory
CAUTION Static electricity can damage DIMMs.  When handling DIMMs, either wear an
antistatic wrist strap or frequently touch the su rface of the DIMM antistatic package, then touch
bare metal on the device.
The HP LaserJet M3027/M3035 devices come with one DIMM slot. If desired, you can replace a DIMM
installed in the slot with a higher memory DIMM.
If you have not already done so, print a configuration page to find out how much memory is installed in
the device before adding more memory. See 
Use information pages .
1. After the configuration page has printed, turn the device off and disconnect the power cord.
2.Disconnect all interface cables.
ENWW Install memory 233
 
						

							3.Remove the right side panel by sliding it towards  the rear of the device until the side slides from
the device.
4. Open the access door by pulling on the metal tab.
5.Remove the DIMM from the antistatic package.
CAUTION To reduce the possibility of damage ca used by static electricity, always wear
an electrostatic discharge (ESD) wrist strap or  touch the surface of the antistatic package
before handling DIMMs.
234 Appendix E   Working with memory and print server cards ENWW
 
						

							6.Hold the DIMM by the edges, and align the notc hes on the DIMM with the DIMM slot. (Check that
the locks on each side of the DIMM slot are open.)
7. Press the DIMM straight into the slot, and press fi rmly. Make sure the locks on each side of the
DIMM snap into place.
NOTE To remove a DIMM, first release the locks.
ENWW Install memory 235
 
						

							8.Close the access door, and press firmly until it snaps into place.
9.To replace the right side panel, line up the alignment arrows and slide the panel toward the front
of the device until it latches into place.
10.Reconnect the interface cabl e(s) and the power cord.
11.Turn the device on.
236 Appendix E   Working with memory and print server cards ENWW
 
						

							Check DIMM installation
After installing the DIMM, make sure that the installation was successful.
Verify that DIMM is installed correctly
1. Turn the device on. Check that th e Ready light is illuminated after the device has gone through the
startup sequence. If an error message appears,  a DIMM might have been incorrectly installed.
See 
Control-panel messages .
2. Print a configuration page (see 
Use information pages ).
3. Check the memory section on the configuration page  and compare it to the configuration page that
was printed before the memory installation. If th e amount of memory has not increased, the DIMM
might not be installed correctly, or the DIMM might  be defective. Repeat the installation procedure.
If necessary, install a different DIMM.
NOTE If you installed a device language (persona lity), check the Installed Personalities and
Options section on the configuration page. Th is area should list the new device language.
Save resources (permanent resources)
Utilities or jobs that you download to the device  sometimes include resources (for example, fonts,
macros, or patterns). Resources that are internally  marked as permanent remain in the device memory
until you turn the device power off.
Use the following guidelines if  you use the page description languag e (PDL) ability to mark resources
as permanent. For technical details, see an appropriate PDL reference for PCL or PS.
● Mark resources as permanent only when it is 
absolutely necessary that they remain in memory
while the device power is turned on.
● Send permanent resources to the device only at t
he beginning of a print job and not while the device
is printing.
NOTE Overusing permanent resources or downloading  them while the device is printing might
affect device performance or th e ability to print complex pages.
ENWW Check DIMM installation 237
 
						

							Enable memory for Windows
1.On the  Start menu,  Settings , and Printers  or Printers and Faxes .
2. Select this device and select  Properties.
3. On the  Configure  tab, click More.
4. In the  Total Memory  field, type or select the total amount of memory that is now installed.
5. Click  OK.
6. Go to 
Check DIMM installation .
238 Appendix E   Working with memory and print server cards ENWW