HP CM8060 User Manual

							
Document typeRecommended paperType of finish
Training manualHP Office
HP Office LG (long grain)
HP Office (prepunched)Matte
User manual HP OfficeHP Office LG (long grain)
HP Office (prepunched) Matte
Table 8-3
  Recommended papers for document types (continued)
ENWW Supported paper 157
 
						

							
Supported paper types for each tray
When you select a paper type, you are instructing the device to use a group of predefined settings to
create the best possible print quality for that type of paper.
CAUTION: Selecting a paper type that does not match the type  of paper that is loaded in the tray can
damage the device.
Table 8-4   Supported paper types for each tray
Paper type that is listed in the
printer driver or on the control
panelDescriptionTray 1Trays 2, 3, and 4Tray 5
PlainPlain, uncoated paper that is less than
150 g/m2 (40 lb bond)
XXX
HP Matte Premium 120gUse only for HP Premium Presentation
Matte Paper, 120 g/m2X  
HP Matte Brochure 180gUse only for HP Brochure and Flyer
Paper Matte, 180 g/m2X  
HP Matte Cover 200gUse only for this HP-brand paper.X  
HP Glossy Edgeline 180gUse only for HP Glossy for Edgeline
Paper, 180 g/m2X  
CardstockPlain, uncoated paper that is from 160
to 220 g/m2 (60 to 80 lb cover)
X  
CardstockPlain, uncoated paper that is from 160
to 180 g/m2 (60 to 67 lb cover)
XXX
MattePlain, uncoated paper.
A3 or 11x17 inch paper must be
long-grain.XXX
Matte BrochurePlain, uncoated paper.
A3 or 11x17 inch paper must be
long-grain.XXX
Matte CoverPlain, uncoated paper that is from 160
to 220 g/m2 (60 to 80 lb cover)
X  
LabelsUncoated, non-glossy labelsX  
LetterheadFine, uncoated paper that is less than
150 g/m2 (40 lb bond)
XXX
PreprintedPlain, uncoated paper that is less than
150 g/m2 (40 lb bond)
XXX
PrepunchedLetter (3-hole) or A4 (2- or 4-hole) size
paper that is less than 150 g/m2 (40 lb
bond)
XXX
Colored Plain, uncoated paper that is less than
150 g/m2 (40 lb bond)XXX
158 Chapter 8   Paper and trays ENWW
 
						

							
Paper type that is listed in the
printer driver or on the control
panelDescriptionTray 1Trays 2, 3, and 4Tray 5
BondFine, uncoated paper that is less than
150 g/m2 (40 lb bond)
XXX
Recycled Plain, uncoated paper that is less than150 g/m2 (40 lb bond)XXX
Supported paper sizes for each tray
Standard paper sizes are marked in the trays.
 To use a custom paper size, use Tray 1.
Table 8-5  Supported paper sizes for each tray
SizeDimensionsTray 1Trays 2, 3, and 4Tray 5
Letter216 x 280 mm
8.5 x 11 inchesXXX
Legal216 x 356 mm
8.5 x 14 inchesXX 
Executive184 x 267 mm
7.25 x 10.5 inchesXX 
Statement140 x 216 mm
5.5 x 8.5 inchesXX 
8.5 x 13216 x 330 mm
8.5 x 13 inchesXX 
11 x 17280 x 432 mm
11 x 17 inchesXX 
12 x 18305 x 457 mm
12 x 18 inchesX  
4 x 6102 x 152 mm
4 x 6 inchesX  
5 x 7127 x 178 mm
5 x 7 inchesX  
5 x 8127 x 203 mm
5 x 8 inchesX  
A3297 x 420 mm
11.69 x 16.54 inchesXX 
A4 210 x 297 mm
8.27 x 11.69 inches XXX
Table 8-4
  Supported paper types for each tray (continued)
ENWW Supported paper 159
 
						

							
SizeDimensionsTray 1Trays 2, 3, and 4Tray 5
A5148 x 210 mm
5.83 x 8.27 inchesXX 
RA3305 x 430 mm
12.01 x 16.93 inchesX  
RA4215 x 305 mm
8.46 x 12.01 inchesX  
SRA4225 x 320 mm
8.86 x 12.6 inchesX  
B4 (JIS)257 x 364 mm
10.12 x 14.33 inchesXX 
B5 (JIS)182 x 257 mm
7.17 x 10.12 inchesXX 
B6 (JIS)128 x 182 mm
5.04 x 7.17 inchesX  
8K273 x 394 mm
10.75 x 15.5 inchesX  
16K197 x 273 mm
7.75 x 10.75 inchesX  
Custom Minimum: 102 x 152 mm(4 x 6 inches)
Maximum: 320 x 457 mm
(12.6 x 18 inches) X  
Table 8-5
  Supported paper sizes for each tray (continued)
160 Chapter 8   Paper and trays ENWW
 
						

							
Capacity of each tray and bin
To avoid jams and print-quality problems, load the trays with the correct amount of paper. Load complete
reams at one time.
Remove paper from the output bins when they are full.
Table 8-6   Capacity of each tray and bin
Tray or binCapacityWeight
Scanner glassOne sheet of paper, up to 305 x 445 mm
(12 x 17.1 inches)
Maximum scanning area is 297 x 433 mm
(11.7 x 17.0 inches)Any weight of paper
Objects, such as books, up to 50 mm
(1.97 inches) high
Document feeder100 sheets of paper, 75 g/m2 (20 lb bond)60 to 135 g/m2 (16 to 36 lb bond)
Tray 180 sheets of paper, 75 g/m2 (20 lb bond)60 to 220 g/m2 (16 to 58 lb bond)
Trays 2, 3, and 4500 sheets of paper, 75 g/m2 (20 lb bond)60 to 180 g/m2 (16 to 48 lb bond)
Tray 54,000 sheets of paper, 75 g/m2 (20 lb bond)
Letter or A4 size only60 to 180 g/m2 (16 to 48 lb bond)
Single output bin250 sheets of paper, 75 g/m2 (20 lb bond)60 to 220 g/m2 (16 to 58 lb bond)
HP Multifunction FinisherOutput Bins 1 and 2: 400 sheets
Output Bins 3 and 4: 200 sheets
Output Bin 5: 2,500 sheets60 to 220 g/m2 (16 to 58 lb bond)
HP 4-Bin Job Separator Output Bins 1 and 2: 400 sheets
Output Bins 3 and 4: 200 sheets 60 to 220 g/m2 (16 to 58 lb bond)
Supported paper sizes for each bin
Table 8-7
  Supported paper sizes for each bin
BinLengthWidth
Output Bins 1, 2, 3, and 4457 to 152 mm (18 to 6 inches)320 to 102 mm (12.6 to 4 inches)
Output Bin 5
(HP Multifunction Finisher only) 432 to 230 mm (17 to 9.1 inches) 297 to 182 mm (11.7 to 7.2 inches)
ENWW
Supported paper 161
 
						

							Load trays
Labels on each tray indicate the correct way to load paper. Each time you load paper into a tray, the
device prompts you to configure the tray for the paper size and type. Always set the paper size and type
to get the best performance from the device.
Load Tray 1 (manual feed tray)
Load standard or custom-sized paper into this tray. It holds up to 80 sheets of 75 g/m2 (20 lb bond)
paper. Also use this tray for heavier paper, such as cardstock, HP Edgeline Glossy, or brochure papers.
1.Slide the tray support up, pull it out, and then pull out the extension.
2.Move the guide outward.
3.Load the paper. Always load the paper with the short edge first.
162 Chapter 8   Paper and trays ENWW
 
						

							
●Load letterhead or preprinted paper with the printed side face-down and the top edge to the
right.
NOTE:
For duplex printing, load letterhead or prepr inted paper with the printed side facing-
up and the top edge feeding first.
● Load prepunched paper with the side that has holes toward the front of the device.
● Load labels with the front side facing down.
● When loading HP Edgeline Glossy paper, fan the paper stack to separate the sheets before
placing them in the tray. This helps prev
ent the sheets from sticking together.
4. Adjust the guide so that it touches the paper.
5.Configure the tray for the type and size of paper.
a. From the Home screen, touch  Supplies Status.
b. Touch the  Trays tab.
c. If the size and type that are listed for the tray  are not correct, touch the name of the tray, and
then touch  Modify.
d. Select the correct paper size and type, and then touch  OK.
-or-
If you are loading a custom paper size, touch  Custom. Type the dimensions of the paper, and
then touch  OK to return to the  Modify Tray screen.
e. Touch  OK to save the settings.
ENWW Load trays 163
 
						

							Load Trays 2, 3, and 4
Trays 2, 3, and 4 hold many standard sizes and types of paper. Each tray holds up to 500 sheets of
75 g/m2 (20 lb bond) paper.
1.Open Tray 2, 3, or 4.
2.Load the paper, whole reams at a time. Always place the long edge along the front side of the tray.
●Load letterhead or preprinted paper with the printed side face-up and the top edge to the left.
NOTE:For duplex printing, load letterhead or preprinted paper with the printed side face-
down and the top edge to the right.
●Load prepunched paper with the edge that has the holes along the front side of the tray.
3.Adjust both guides so that they click into the position that is marked for the paper size.
164 Chapter 8   Paper and trays ENWW
 
						

							4.Slide the tray into the device.
5.Configure the tray for the type of paper by responding to the pop-up message that appears on the
touchscreen when you close the tray. Or, follow these steps:
a.From the Home screen, touch Supplies Status.
b.Touch the Trays tab.
c.If the type that is listed for the tray is not correct, touch the name of the tray, and then touch
Modify.
d.Select the correct paper type, and then touch OK.
ENWWLoad trays 165
 
						

							Load Tray 5
This tray is preconfigured to hold up to 4,000 sheets (8 reams) of either Letter-size or A4-size paper.
You cannot change this size setting. 
1.Open the Tray 5 top door, and load the paper. Load whole reams at a time. The tray lowers itself 
as you load more paper. 
●Load letterhead or preprinted paper with the printed side face-down and the top edge to the 
right.
NOTE:For duplex printing, load letterhead or preprinted paper with the printed side facing-
up and the top edge feeding first.
●Load prepunched paper with the side that has holes toward the front of the device.
2.Configure the tray for the type of paper by responding to the pop-up message that appears on the
touchscreen when you close the tray. Or, follow these steps: 
a.From the Home screen, touch Supplies Status.
b.Touch the Trays tab.
c.If the paper type that is listed for the tray is not correct, touch the name of the tray, and then
touch Modify.
d.Select the correct paper type, and then touch OK.
166 Chapter 8   Paper and trays ENWW