Norstar Compact 616 Dr5 Installer Guide

							34  Programming
Set Copy
Use this for copying System data (programming) or System and
User Administration data (Personal programming) from one
telephone to another. System data is programmed in
Configuration and Administration. User Administration
programming is performed by the user at the individual
telephone, and allows the telephone to be customized according
to the user’s requirements.
Set Copy Options
 data
When this message appears on the display, you can choose to
copy System data.
When this message appears on the display, you can choose to
copy System and User data. Both telephones must be the same
model and connected to the system before this option can be
used.
 Do not confuse C. Set COPY with the  display
button (or 
 on the M7208 Telephone), which is
for selective copying of specific groups of settings from
one telephone or external line to another. 
						

							  
Set Copy characteristics which can NOT be copied
 
  options
 Log     
 Directory  
    
 Private line appearances
Prime telephone designation for a line
 Direct-dial telephone designation
 Extra-dial telephone designation
 Control telephone designation for a line
Service mode Ringing telephone designation for a line
 Receive tones
 Logging set designation
 Show external Voice Message
 Log space
 First display
Compact  Installer Guide 
						

							36  Programming
Characteristics which CAN be copied
Except for those characteristics previously listed, all telephone
related settings can be copied to a destination telephone,
overriding any previous programming. Listed below are the
System level settings and User Administration settings which can
be copied.
System settings in Configuration programming
2.Line 
Line assignment
Answer 
Ringing line preference
Line pool access
Number of Intercom buttons
Prime line designation 
						

							Programming  37
System settings in Administration programming
5.  
 Set Filter
  
 Full handsf ree
 Wandsfree answerback
 pickup group
 Paging
 Auxiliary ringer
 Direct-Dial
 Forward on busy
 Forward on no answer
 Receive tones
 Priority call
9.  Services
  Vmsg
 settings
if desired, the following Personalized settings can be copied
along with the System data:
 Programmable button assignments (Internal Autodial,
External Autodial, and feature access)
 Language choice
 Personal Speed Dial entries
Compact  Installer Guide 
						

							38  Programming
Using Set Copy
You can only enter Set Copy through the Configuration access
code and with the Installer password.
Entering Set Copy
After   appears on the display:
1.Press  twice.
The display shows 
C. Set COPY.
2. Press  to go to COPY:  data.
Chart 11 Set Copy
C. Set cowD. Uersion
COPY:  data
Enter  pad digits
Back
. 
						

							Testing the  and 
   external lines by selecting each line in turn at one
of the  and verifying the  tone. If you do 
get a  tone; plug a single-line  into the
 line at the distribution panel. If you still do not get a
dial tone, check all your wiring or contact your telephone
company.
2.Check all internal connections by calling each 
telephone from another  telephone.
3. the quality and clarity of all connections. Check for
crackling, static, hums, or any other unusual noise,
4.If there are any problems, refer to other procedures in this
section.
5.Verify the visual indicators:
To check a button:
1.Select a line or Intercom button. The  indicator beside
that button should appear.
To check the display:
1.Press 
The display shows Press a button.
2.Press the  button to exit from this feature.
Compact  installer Guide 
						

							40  Troubleshooting,
 Terminal Adapter  trouble
 Check the single line telephone connection by using an
installer’s test telephone.
2. Check the connections to the jack. 
 
3. Check the connections to the 
4.Disconnect the  and replace it with a working Not-star
telephone. If the telephone still works properly, this verifies
that the KSU is working properly.
5.Verify that programming has been done as described in the
 Analog Terminal Adapter Installation Card.
6.If the trouble seems to be in the KSU, double check all wiring
and programming options. If this does not help, refer to the
KSU down section of Troubleshooting.
WARNING
This unit must be powered from a Class  source
that is UL and CSA Listed.
Auxiliary Ringer trouble
1.If the Auxiliary Ringer is used for Service Modes, ensure that
Service Modes is activated from the Control Telephone.
2.Check the wiring between the Auxiliary Ringer generator and
the ringing device. (See the Internal Wiring chart.)
3.Check the wiring between the Auxiliary Ringer and the
distribution panel.
4.Check the Auxiliary Ringer contact operation with an
ohmmeter across the pins.
5.Check that the Auxiliary Ringer is programmed to ring for
any of the following programmable settings: 
						

							Troubleshooting  41
FeatureProgrammed in:
Ring for a specific line A. Configuration (1.  Data)
Ring ‘for a specific General  (5. Capabilities)
  ___
Service Modes 
Ringer  
    (6, Service Modes)  
 ,
  Installer Guide 
						

							42  Troubleshooting
Cal  Identification Interface
1.Use the Call Information feature on an incoming call to verify
the operation 
of the 
2Check the connections to the Cll. Refer to the
 Installer Card for installation details., 
3.Verify that the programming has been done as described in
the Compact 
 Programming Record and the Compact
 System Coordinator Guide.
4.Verify that you are subscribing to visual Call Display services
from your local telephone company.
5. Replace the 
Dial tone absent (on external lines)
1.Use Button Inquiry    to check the feature of
a programmable memory button that you think is assigned
as an external line.
2.Check for a dial tone by using an installer’s test telephone at
the connections for the external line on the distribution block.
3.Check the connections between the KSU and the distribution
block.
External Paging trouble
1.Check the wiring between the  connector and the
paging amplifier.
2.Check the wiring between the connections shown in the
Internal Wiring chart.
3.Test the external Page feature    to ensure
that it is working. The output from the 
 KSU is
775  across 600  
						

							Troubieshooting  43
KSU down
1.Check that the AC power cord is properly connected.
  that the Software Cartridge  seated in its slot.
  is  
3.If AC power  and the LED indicator on the KSU is
OFF, replace the KSU.