Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation For Adjuncts And Peripherals Manual

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Data Modules and Asynchronous Data Units 
59 Connect Data Modules 
4
The current transmission speed appears: SPEED = 56KBPS? 
 (the 
d efault) or SPEED = 64KBPS? 
3. To keep the existing sp eed , p ress the ENTER/YES button.    
4. To c hange the existing  speed , p ress NEXT/NO
.  
When the SPEED ->
NewSpeed?
 prompt appears, press the ENTER/YES 
button.  
5. The CONTINUE?
 prompt appears. Press the ENTER/YES
 b utton.  
6. If you want to set any other op tions, skip  to the following  sec tion. 
7. Otherwise, if you want to q uit now, press NEXT/NO until DONE?
 ap p ears. 
Then press the ENTER/YES button.  
SPEED = 56 KBPS?
DATANEXT/NO BACK ENTER/YES
l  m m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
)
SPEED = 56 KBPS?
DATANEXT/NO BACK ENTER/YES
lÜ l m m
Push the b utton ind ic ated  b y the arrow (Ü
)
SPEED -> 64 KBPS?
DATANEXT/NO BACK ENTER/YES
l  m m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
)
CONTINUE?
DATANEXT/NO BACK ENTER/YES
lmmÜ l
Push the b utton ind ic ated  b y the arrow (Ü
)
DONE?
DATANEXT/NO BACK ENTER/YES
lmmÜ l
Push the b utton ind ic ated  b y the arrow (Ü
) 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Data Modules and Asynchronous Data Units 
60 Connect Data Modules 
4
8. When SAVE CHANGES? 
app ears, press the ENTER/YES button again. 
CHANGES SAVED
 ap pears, and  the d ata mod ule returns to the HOME 
sc reen.
Setting other data options for the 7400C
You c an usually use the default setting s for all other op tions. However, two 
exc ep tions are d isc ussed below.  
Selecting data inversion for 64-kbps, HDLC transmissions on restricted 
facilities 
Data inversion is available when you are transmitting at 64 kbps over restricted 
fac ilities using HDLC-b ased  p rotoc ols. Proc eed as follows.
1. If you need  c omp atib ility with an ACCUNET MPDM, set DATA INVERSION
 
to ON
 using  the menus and  c ontrols as d esc rib ed  ab ove, in ‘‘Setting  the 
d ata sp eed  for the 7400C’’.
2. Otherwise, set DATA INVERSION
 to OFF
.
3. Exit and  save c hang es, as desc rib ed  ab ove, in ‘‘Setting  the d ata speed  for 
the 7400C’’.
Configuring the 7400C for a dedicated private line
The fac tory d efault setting s assume that the d ata module c onnec ts to a switc hed , 
d ial-up  line. Private lines are p ermanent, unswitc hed c onnec tions, so they have 
to b e sp ec ially c onfig ured . Proc eed  as follows.
1. Set the d ialing  method  to MANUAL
, 
using  the menus and  c ontrols as 
described above, in ‘‘Setting  the d ata sp eed  for the 7400C’’
.
2. Set the answering  mod e (ANS
) to AUTO
.
3. Set the DTR
 lead  to IGNORE
.
4.  Set the DSR
 lead  to ON
.
5. Set PERMANENT CONNECTION
 to YES
.
6. Exit and  save c hang es, as desc rib ed  ab ove, in ‘‘Setting  the d ata speed  for 
the 7400C’’.
SAVE CHANGES?
DATANEXT/NO BACK ENTER/YES
lmmÜ l
Push the b utton ind ic ated  b y the arrow (Ü
) 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Data Modules and Asynchronous Data Units 
61 Connect Data Modules 
4
Configuring the 7400D Data Module
The 7400D d ata mod ule is a c onverted  7400A used  for sync hronous data 
transmission (Fi g u re  1 6
). It is a direct replac ement for the MPDM. You configure 
the 7400D just as you would  a 7400A, exc ep t that  there is no SET INTERFACE 
op tion (the 7400D is an answer-only d evic e that c annot orig inate c alls). It 
supports DCE mode only. DTE modem-pooling is not supported. The PHONE  
and  PORT2 c onnec tors are not used . 
The following tab le lists rec ommend ed  setting s for a typ ic al installation. For the 
c onfig uration p roc ed ure, see the sub seq uent sec tions. 
Recommended settings for typical  configurations
The tab le b elow summarizes the rec ommend ed  c onfig uration values for the 
7400D d ata mod ule. The p roc ed ures for setting  these values follow. 
Options  CMS settings DCS settings
300 OFF OFF
1200 OFF OFF
2400 OFF OFF
4800 OFF OFF
9600 ON (OFF for R8r) ON
19200 OFF (ON for R8r) OFF
ANSWER AUTO AUTO
CI OFF ON
CH LEAD OFF OFF
CTS LEAD NORMAL NORMAL
DCD LEAD NORMAL ON
DSR LEAD NORMAL ON
DTR DETECT 50 MSEC  50 MSEC 
DTR LEAD FOLLOW IGNORE
RI LEAD ON ON
SIGLS DISC ON ON
TM LEAD OFF OFF
Continued on next page 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Data Modules and Asynchronous Data Units 
62 Connect Data Modules 
4
Figure 16. 7400D Data Module 
Accessing the menus of the 7400D
You c onfig ure the 7400D from a set of menus.
1. To ac c ess the menus, p ress the NEXT/NO
 b utton.  
2. When the SET OPTIONS?
 p romp t ap p ears on the LCD. Press the NEXT/
NO
 b utton. 
00—0 0 0 ——
DATANEXT/NO BACK ENTER/YES
lÜ l m m
Push the b utton ind ic ated  b y the arrow (Ü
)
SET OPTIONS?
DATANEXT/NO BACK ENTER/YES
lÜ l m m
Push the b utton ind ic ated  b y the arrow (Ü
) 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Data Modules and Asynchronous Data Units 
63 Connect Data Modules 
4
3. The VIEW OPTIONS?
 prompt appears. Press the NEXT/NO
 b utton. 
Setting speed options for the 7400D
The d ata speed  d ep end s on the exac t ap p lic ation, b ut most req uire 9600 b p s or, 
less c ommonly, 19200. 
1. Press the NEXT/NO
 b utton to c ontinue with the setup  p roc ed ure.  
2. The SET OPTIONS?
 p rompt ap p ears on the LCD. Press the ENTER/YES
 
b utton. 
A series of SET 
number SPEED?
 prompts appears.   
3. Press the NEXT/NO
 b utton until you see the SET 
yourSpeed SPEED?
 
p rompt. Then p ress the ENTER/YES
 b utton.   
VIEW OPTIONS?
DATANEXT/NO BACK ENTER/YES
lÜ l m m
Push the b utton ind ic ated  b y the arrow (Ü
)
00—0 0 0 ——
DATANEXT/NO BACK ENTER/YES
lÜ l m m
Push the b utton ind ic ated  b y the arrow (Ü
)
SET OPTIONS?
DATANEXT/NO BACK ENTER/YES
l mmÜ l
Push the b utton ind ic ated  b y the arrow (Ü
)
SET yourSpeed SPEED?
DATANEXT/NO BACK ENTER/YES
l mmÜ l
Push the b utton ind ic ated  b y the arrow (Ü
) 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Data Modules and Asynchronous Data Units 
64 Connect Data Modules 
4
4. Press the NEXT/NO
 b utton until you see the yourSpeed=ON?
 p romp t.  
Then press the ENTER/YES
 b utton. 
5. If the CONTINUE? 
p romp t ap pears, p ress the ENTER/YES
 b utton.
Setting the automatic-answer feature on the 7400D
You c an set up  the 7400A d ata mod ule to automatic ally answer c alls or you c an 
have it ig nore c alls until an op erator answers manually. Set up  the d ata mod ule 
for automatic  answering  unless sp ec ific ally d irec ted to otherwise.
1. When the SET ANSWER?
 p romp t app ears, press the ENTER/YES
 
b utton.  
2. When the ANS = AUTO?
 p romp t ap p ears, press the ENTER/YES
 button 
for most ap p lic ations.   
Configuring the RS-232 interface of the 7400D
From the front p anel, you c an set eac h p in of the RS-232 c ab le to meet the need s 
of sp ec ific  ap p lic ations, thoug h in most c ases, the setting s b elow should  work.
yourSpeed=ON?
DATANEXT/NO BACK ENTER/YES
l mmÜ l
Push the b utton ind ic ated  b y the arrow (Ü
)
CONTINUE?
DATANEXT/NO BACK ENTER/YES
l mmÜ l
Push the b utton ind ic ated  b y the arrow (Ü
)
SET ANSWER?
DATANEXT/NO BACK ENTER/YES
l mmÜ l
Push the b utton ind ic ated  b y the arrow (Ü
)
ANS = AUTO?
DATANEXT/NO BACK ENTER/YES
l mmÜ l
Push the b utton ind ic ated  b y the arrow (Ü
) 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Data Modules and Asynchronous Data Units 
65 Connect Data Modules 
4
1. When the SET CI LEAD?
 promp t ap p ears, p ress the ENTER/YES
 b utton. 
2. Press the NEXT/NO
 button until you see the
 CI = correctSetting?
 or CI -> 
correctSetting? 
p romp t. Then p ress the ENTER/YES
 b utton. 
3. When the CONTINUE?
 prompt appears, press the ENTER/YES
 b utton. 
4. When the SET CH LEAD?
 p romp t app ears, press the ENTER/YES
 
b utton. 
5. Press the NEXT/NO
 button until you see the
 CH = correctSetting?
 or CH -
> 
correctSetting? 
p romp t. Then p ress the ENTER/YES
 b utton. 
6. When the CONTINUE?
 prompt appears, press the ENTER/YES
 b utton. 
SET  CI LEAD?
DATANEXT/NO BACK ENTER/YES
l mmÜ l
Push the b utton ind ic ated  b y the arrow (Ü
)
CI = correctSetting?
DATANEXT/NO BACK ENTER/YES
l m m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
)
CONTINUE?
DATANEXT/NO BACK ENTER/YES
lm m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
)
SET  CH LEAD?
DATANEXT/NO BACK ENTER/YES
l mmÜ l
Push the b utton ind ic ated  b y the arrow (Ü
)
CH = correctSetting?
DATANEXT/NO BACK ENTER/YES
lm m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
) 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Data Modules and Asynchronous Data Units 
66 Connect Data Modules 
4
7. When the SET CTS LEAD?
 prompt appears, press the ENTER/YES
 
b utton. 
8. Press the NEXT/NO
 b utton until you see the CTS =
 correctValue?
 or  
CTS ->
 correctValue? 
p rompt. Then p ress the ENTER/YES
 b utton. 
9. When the CONTINUE?
 prompt appears, press the ENTER/YES
 b utton. 
10. When the SET DCD LEAD?
 p romp t ap pears, p ress the ENTER/YES
 
b utton. 
11. Press the NEXT/NO
 b utton until you see the DCD = 
correctValue?
 or 
DCD -> 
correctValue? 
p romp t. Then p ress the ENTER/YES
 b utton. 
12. When the CONTINUE?
 prompt appears, press the ENTER/YES
 b utton. 
SET  CTS LEAD?
DATANEXT/NO BACK ENTER/YES
lm m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
)
CTS ->  correctValue?
DATANEXT/NO BACK ENTER/YES
lm m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
)
SET  DCD LEAD?
DATANEXT/NO BACK ENTER/YES
lm m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
)
DCD = correctValue?
DATANEXT/NO BACK ENTER/YES
lmm Ü l
Push the b utton ind ic ated  b y the arrow (Ü
) 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Data Modules and Asynchronous Data Units 
67 Connect Data Modules 
4
13. When the SET DSR LEAD?
 p rompt ap p ears, p ress the ENTER/YES
 
b utton. 
14. Press the NEXT/NO
 b utton until you see the DSR = 
correctValue? 
or DSR 
-> 
correctValue?
 p romp t. Then p ress the ENTER/YES
 b utton. 
15. When the CONTINUE?
 prompt appears, press the ENTER/YES
 b utton. 
16. When the SET DTR DETECT?
 promp t ap p ears, p ress the ENTER/YES
 
b utton. 
17. Press the NEXT/NO
 b utton until you see the DTR =
correctValueMSEC? 
or DTR -> 
correctValue MSEC?
 p romp t. Then p ress the ENTER/YES
 
b utton. 
18. When the CONTINUE?
 prompt appears, press the ENTER/YES
 b utton. 
SET  DSR LEAD?
DATANEXT/NO BACK ENTER/YES
lm m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
)
DSR -> correctValue?
DATANEXT/NO BACK ENTER/YES
lm m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
)
SET  DTR DETECT?
DATANEXT/NO BACK ENTER/YES
lm m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
)
DTR = correctValue MSEC?
DATANEXT/NO BACK ENTER/YES
lm m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
) 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Data Modules and Asynchronous Data Units 
68 Connect Data Modules 
4
19. When you see the SET DTR LEAD?
 p romp t, p ress the ENTER/YES
 
b utton. 
20. Press the NEXT/NO
 b utton until the DTR = 
correctValue?
 or DTR -
>
correctValue?
 prompt appears. Then  press the ENTER/YES
 b utton. 
21. When the CONTINUE?
 prompt appears, press the ENTER/YES
 b utton. 
22. When the SET LL LEAD?
 p rompt ap p ears, p ress the NEXT/NO
 b utton to 
skip this setting . 
23. When the SET LL DETECT?
 promp t ap p ears, p ress the NEXT/NO
 button 
to skip  this setting . 
24. When the SET RI LEAD?
 promp t ap p ears, p ress the ENTER/YES
 b utton. 
SET  DTR LEAD?
DATANEXT/NO BACK ENTER/YES
lm m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
)
DTR = correctValue?
DATANEXT/NO BACK ENTER/YES
l  m m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
)
SET  LL LEAD?
DATANEXT/NO BACK ENTER/YES
lÜ l m m
Push the b utton ind ic ated  b y the arrow (Ü
)
SET  LL DETECT?
DATANEXT/NO BACK ENTER/YES
lÜ l m m
Push the b utton ind ic ated  b y the arrow (Ü
)
SET  RI LEAD?
DATANEXT/NO BACK ENTER/YES
lm m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
)