Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation For Adjuncts And Peripherals Manual

							DEFINITY INADS 
149  
14
DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
14
DEFINITY INADS
The DEFINITY ECS Initialization and  Administration System (INADS) p rovid es 
analog  loop bac k c onnec tions and  PARTNER® c onnec tions for remote alarming 
and  maintenanc e when d irec t c onnec tion to the p ub lic  network is not p ossib le.
NOTE:
These instruc tions are for DEFINITY ECS Release 7r or later systems using  
the TN1648/B system ac c ess/maintenanc e (SYSAM) c irc uit pac k. ISDN is 
req uired .
Analog Loopback 
Analog  loop b ac k c onnec ts the INADS p ort to an analog  station p ort. It switc hes 
the c all throug h the AUX c onnec tor on the p roc essor c arrier of the DEFINITY 
ECS, ac ross an analog  line c irc uit p ac k, and  out to the p ub lic  network. Direc t 
Inward  Dialing  (DID) is op tional.
Installing INADS Analog Loopback on a 
Standard-Reliability System
1. Connec t the INADS tip  and ring  p ort from the AUX c onnec tor to an analog  
station p ort via the MDF. See Fig ure 45
. Use wire pair 50 and 25.
2. If you are using  p ower-fail transfer, c onnec t the 808A2 transfer p anel 
b etween the INADS c onnec tion to the station and  the INADS c onnec tion to 
the loop -start trunk. 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
DEFINITY INADS 
150  
14
Figure 45. Analog Loopback Connections R8r
Installing INADS Analog Loopback on a High-
Reliability System
Be  su re  t o  p la c e  t h e  TN 1 6 4 8 B  SYSAM  c irc u i t  p a c ks  i n  d iff e re n t  c a b i n e t s  o r 
p roc essor c arriers. Also b e sure to p lac e the analog  line c irc uit p ac ks in the 
same c ab inets or c arriers as the TN1648 c irc uit p ac ks.
1. Connec t eac h INADS tip /ring  p ort to an analog  station p ort via the MDF. 
See Fig ure 45
. 
2. Connec t eac h tip /ring  p ort to a sep arate analog  line c irc uit p ac k. 1. Release 8r PPN c ab inet
2. AUX c onnec tor on proc essor c arrier 
(use wire p air 50 and  25, tip  and ring )
3. Port c arrier (with analog  line c irc uit p ac k)4. B25A 25-pair c able to AUX
5. Main d istrib ution frame (MDF)
6. B25A 25-pair c able to c ircuit pack
7. PSTN or DEFINITY extension
cydfmdf RPY 040698
1
4
6
5
3
2
7 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
DEFINITY INADS 
151  
14
Administering DEFINITY ECS for INADS
NOTE:
Ad d 2 p auses in front of the d ial string  when using  c ut-throug h trunks. 
Pauses are not required if using ARS.
1. Type change system-parameters maintenance
 and press 
En t e r.
2. For hig h reliab ility systems, in the see interchange: 
field, type daily
 
and  p ress 
En t e r. This is d one in c ase 1 of the c onnec tions b etween the 2 
TN1648B c irc uit p ac ks is d own. This assures that within 24 hours the 
working  c onnec tion is available to report alarms.
3. Type add station
 
number or next
 and press En t e r.
4. In the Type:
 field , enter 500
 (rotary analog telep hone).
5. In the Port:
 field , enter the p ort numb er for this line.
6. For hig h reliab ility systems, rep eat the ab ove step s for the sec ond  analog  
line. Ad minister the 2 stations as p art of a TEG (terminating  extension 
group).
a. Type add term-ext-group
 
number or next
 and p ress En t e r.
b . In the Group Extension:
 field, enter the TEG extension numb er.
c . In the Coverage Path:
 field, enter the c overag e p ath numb er.
d . Enter the Group  Memb er Assig nment station numbers. Press 
En t e r 
when finished.
Partner Installation
The PARTNER system c onnec ts the DEFINITY ECS INADS p ort to an outg oing  
c entral offic e (CO) line and  is p rog rammed  to seize the outsid e line when INADS 
seizes an insid e PARTNER station line. 
Listed  b elow are the 2 typ es of PARTNER p latforms:
n
PARTNER Atlas platforms with U.S. firmware and a wide input power 
sup p ly (WIPS) that allows a universal p ower sup p ly. The Sp ain p latform 
c onforms to the United States/Atlas platform
n
European p latforms that foc us on eastern Europ e and  the United  King d om
The installation p roc edure d esc rib es the 2 typ es of PARTNER p latforms with or 
without p ower fail transfer. 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
DEFINITY INADS 
152  
14
INADS Connection (with Power Fail Transfer)
!CAUTION:
Chec k loc al reg ulations reg ard ing  this c onnec tion method .
In this c onfig uration, the INADS line and  the emergenc y telep hone extension are 
bridged together. Fi g u re  4 6
 shows the U.S./Atlas p latform. Fi g u re  4 7 shows the 
European p latform.
Figure 46. INADS Connection (US/Atlas Platform)1. PARTNER System
2. MLS12D telep hone for p rogramming
3. Internal c onnec tion d uring  p ower 
failure, from CO line p ort 1 to station 
port 10
4. 258A ad ap ter (b rid g ed  c onnec tion)
5. Stand ard  RJ-45 telep hone c ord
6. 103A or modular wall jack7. Dial tone from CO or DEFINITY extension
8. Main distribution frame
9. PSTN or DEFINITY extension
10. B25A 25-p air c ab le to AUX
11. AUX c onnec tor (use wire p air 50 and  25, 
tip and ring)
1 2 . D EFI N I TY Re le a se  8 r  PPN  c a b in e t
cydf206 RPY 021998
1
L
I
N
E
S
E
X
T
E
N
S
I
O
N
S
PFT PFT
206
MOD ULE
R2.0
4
5
12
11
106
3
78
2
9 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
DEFINITY INADS 
153  
14
Figure 47. INADS Connection (European Platform)
Standard Reliability 
nNormal connection
: Connec t the INADS tip  and  ring  p ort from the AUX 
c onnec tor (wire p air 50 and  25) to the tip /ring  p air of CO line p ort 1 on the 
PARTNER system. 
nUS/Atlas/Spain platform connection
: Connec t station 10 to the INADS 
port. 
nEuropean platform connection
: Brid g e the outsid e p air of CO line p ort 1 
to the INADS p ort. A 258A ad ap ter may b e used . 1. PARTNER System
2. MLS12D telep hone for p rog ramming  
3. Stand ard  RJ-45 telep hone c ord
4. 103A or mod ular wall jac k
5. Pins 2,3 on c ab le 5 b ridg e to p ins 1,4 
of cable 7 inside MDF
6. Dial tone from the CO or DEFINITY 
extension on p ins 2,3; with return d ial 
tone to the INADS p ort on p ins 1,4 
during power failure7. Main d istrib ution frame (MDF)
8. PSTN or DEFINITY extension
9. B25A 25-p air c ab le to AUX
10. AUX c onnec tor (use wire p air 50,25, tip  and  
ring )
11. DEFINITY Release 8r PPN c ab inet
12. Stand ard  RJ-45 c onnec tor (p ins 2,3, tip and 
ring , c onnec t to pins 1,4, tip  and  ring , when 
the internal c ontac ts c lose d uring  p ower 
failure)
1
L
I
N
E
S
E
X
T
E
N
S
I
O
N
S
PFT PFT
206
MO DU LE
R2.0
cydf206a RPY 021998
9
4
5
2
7
3
6
12
10
11
1234
8 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
DEFINITY INADS 
154  
14
High Reliability
Be  s u re  t h a t  t h e  TN 1 6 4 8 B  SYSAM  c irc u i t  p a c k s a re  l o c a t e d  in  d i ff e re n t  D EFI N I TY 
c ab inets or proc essor c arriers. 
1. Bridg e the 2 INADS tip /ring  ports. A 258A ad ap ter may b e used . 
2. Connect the bridged INADS tip/ring port to a PARTNER station port.
INADS Connection (without Power Fail Transfer)
!CAUTION:
Chec k loc al reg ulations reg ard ing  this c onnec tion method .
In this c onfig uration, the INADS line and  the emergenc y telep hone extension are 
b rid g ed  tog ether. If this c onnec tion method  is not allowed , d o not c onnec t the 
INADS p ort to station 10.
Figure 48. INADS Connection (all platforms)1 . PA RTN ER s y s t e m
2. MLS12D telep hone for prog ramming
3. Stand ard  RJ-45 telep hone c ord
4. 103A or mod ular wall jac k
5. Dial tone from the CO or a DEFINITY 
extension6. Main d istrib ution frame
7 . PSTN
8. B25A 25-p air c ab le
9. AUX c onnec tor (use wire p air 50,25, tip 
and ring)
10. DEFINITY Release 8r PPN c ab inet
cydf206b RPY 021998
1
L
I
N
E
S
E
X
T
E
N
S
I
O
N
S
PFT PFT
206
MODULE
R2.0
4
5
10
9
3
7
82
6 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
DEFINITY INADS 
155  
14
Standard Reliability
Normal c onnec tion:
1. Connec t a system telep hone to station 10 on the PARTNER system.
2. Connec t a stand ard  RJ-11 telephone line c ord  from the PARTNER CO line 
to the CO line p rotec tor.
3. Connec t the INADS tip and  ring p ort from the AUX c onnec tor to the tip /ring  
p air of CO line p ort 1 on the PARTNER via the MDF. See Fig ure 48
. Use 
wire p air 50 and  25 on the MDF.
U.S./Atlas/Sp ain p latform c onnec tion: 
1. Selec t station 11-15 as the INADS p ort c onnec tion.
European p latform c onnec tion: 
1. Bridg e the outsid e p air of CO line p ort 1 to the INADS p ort. A 258A 
ad ap ter may b e used .
High Reliability
Be  su re  t h a t  t h e  TN 1 6 4 8 B  SYSAM  c irc u i t  p a c ks  a re  l o c a t e d  in  d iff e re n t  c a b i n e t s  
or p roc essor c arriers. 
1. Bridg e the 2 INADS tip /ring  ports. A 258A ad ap ter may b e used . See 
Fi g u re  4 8
. 
2. Connect the bridged INADS tip/ring port to a station port.
PARTNER Administration
Set Standard Telephone Station (European 
Platforms Only)
NOTE:
Do not exit from the prog ramming  mod e until instruc ted  to do so.
1. Connec t the PARTNER p rogramming  telep hone (MLS12) to station 10.
2. Press Feature, followed by 0 0. 
3. Press the left interc om (System Prog ram) b utton twic e.
4. Enter the p assword . The default p assword  is 7777
. The g reen LED next to 
the left interc om b utton must be stead y on.
5. Enter # 3 0 8
. 
6. Enter 1 0
 (if station 10 is c onnec ted  to the INADS p ort) or the station 
numb er c onnec ted  to the INADS p ort. 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
DEFINITY INADS 
156  
14
7. Enter 2
 to set the station p ort to analog  rotary. Enter 1
 if an analog  DTMF 
telep hone or PARTNER system telep hone is c onnec ted .
8. Enter #
 to return to the start of the p rog ramming  mode.
Set PARTNER CO Line Port (All Platforms)
1. Enter # 2 0 1
. 
2. Press 1
 for tone or 2
 for pulse mode.
3. Enter #
 to return to the start of the p rog ramming  mode. 
Set Automatic Line Selection — Outgoing Trunk 
(All Platforms)
1. Press the rig ht interc om (Central Tel Prog ram) b utton.
2. Enter 1 5
 (if INADS is c onnec ted  to station 15) or enter the station numb er 
c onnec ted  to the INADS p ort.
3. Enter * *
.
4. Press the line 1 b utton (ab ove left interc om). If the 2 lines are c onnec ted  to 
the PARTNER for ad d ed  reliab ility or sec urity, p ress Next Proc ed ure.
5. Enter * *
.
6. Enter #
 to return to the start of the p rog ramming  mode.
Set Incoming Line Ringing (All Platforms)
1. Press the rig ht interc om (Central Tel Prog ram) b utton.
2. Enter 1 5
 (if INADS is c onnec ted  to station 15) or enter the station numb er 
c onnec ted  to the INADS p ort.
3. Press the line 1 b utton (ab ove left interc om) until the LED c hang es to a 
stead y g reen. This allows inc oming  c alls to ring  on line 1.
4. If AUDIX is installed , p ress the line 2 b utton until the LED c hang es to a 
stead y g reen. This allows inc oming  c alls to ring  on line 2.
5. Enter #
 to return to the start of the p rog ramming  mode.
6. Press Feature, followed by 0 0 to exit the programming mode.
DEFINITY ECS Administration
By d efault, the INADS p ort automatic ally seizes an outg oing  trunk on the 
PARTNER system. Therefore, a “9”  is not required in the switch dial string. 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
DEFINITY INADS 
157  
14
Installation Test (All Installations)
These tests c onfirm that the hard ware and  ad ministration are c orrec t.
1. Plac e an outg oing  c all from the INADS p ort. Chec k for normal talk p ath.
2. Plac e an inc oming  c all to the INADS p ort. Chec k for normal talk p ath.
3. Plac e an outg oing  d ata from the INADS p ort to verify c onnec tion.
A failure in the link b etween the remote servic e c enter and the TN1648Bs INADS 
p ort c an be d etec ted  automatic ally. 
1. Type change system-parameters maintenance
 and press 
En t e r.
2. Set the Test Remote Access Port:
 field  to y
 and press 
En te r.  
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
DEFINITY INADS 
158  
14