Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation For Adjuncts And Peripherals Manual

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Data Modules and Asynchronous Data Units 
69 Connect Data Modules 
4
25. Press the NEXT/NO
 b utton until the RI = correctValue?
 or RI -
>
correctValue?
 prompt appears. Then press the ENTER/YES
 b utton. 
26. When the CONTINUE?
 prompt appears, press the ENTER/YES
 b utton. 
27. When the SET RL LEAD?
 prompt appears, press the NEXT/NO
 b utton to 
skip this setting .  
28. When the SET SIGLS DISC?
 p romp t ap p ears, press the ENTER/YES
 
b utton. 
29. Press the NEXT/NO
 b utton until the SIGLS DISC = 
correctValue?
 or 
SIGLS DISC -> 
correctValue? 
prompt appears. Then press the ENTER/
YES
 button. 
30. When the CONTINUE?
 prompt appears, press the ENTER/YES
 b utton.
SET  RI = ON?
DATANEXT/NO BACK ENTER/YES
lm m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
)
SET  RL LEAD?
DATANEXT/NO BACK ENTER/YES
lÜ l m m
Push the b utton ind ic ated  b y the arrow (Ü
)
SET SIGLS DISC?
DATANEXT/NO BACK ENTER/YES
lm m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
)
SIGLS DISC = ON?
DATANEXT/NO BACK ENTER/YES
lm m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
) 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Data Modules and Asynchronous Data Units 
70 Connect Data Modules 
4
31. When the SET TM LEAD?
 p romp t app ears, press the ENTER/YES
 
b utton. 
32. Press the NEXT/NO
 b utton until the TM = OFF?
 or TM -> OFF? 
prompt 
ap p ears, then p ress the ENTER/YES
 b utton. 
33. When the DONE?
 promp t ap p ears, p ress the ENTER/YES
 b utton. 
34. When the SAVE CHANGES?
 p romp t ap p ears, press the ENTER/YES 
 
b utton. 
Th e  CHANGES SAVED
 messag e flashes on sc reen, and  you return to the  
HOME sc reen. The d ata mod ule is now c onfig ured .
Configuring the 8400B Plus Data Module
Fi g u re  1 7 shows the rear of a 8400B p lus async hronous d ata mod ule. The unit 
p rovid es integrated  voic e and  d ata c ommunic ations over standard , 2-wire, 
twisted -p air c irc uits within 2000 ft. of a DEFINITY. The unit c an emulate a Hayes-
c omp atib le interfac e for stand ard  p ersonal c omp uter (PC) c ommunic ation. The 
op tions for the 8400B Plus are set from the rear p anel interfac e. Refer to 
DEFINITY Communic ations System User’s Guid e for procedures.
SET TM LEAD?
DATANEXT/NO BACK ENTER/YES
lm m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
)
TM = OFF?
DATANEXT/NO BACK ENTER/YES
lm m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
)
DONE?
DATANEXT/NO BACK ENTER/YES
lm m Ü l
Push the b utton ind ic ated  b y the arrow (Ü
)
SAVE CHANGES?
DATANEXT/NO BACK ENTER/YES
lmm Ü l
Push the b utton ind ic ated  b y the arrow (Ü
) 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Data Modules and Asynchronous Data Units 
71 Connect Data Modules 
4
Figure 17. 8400B Plus Data Module 
Installing required configuration equipment for the 8400B
Before you c an enter c onfig uration c ommand s, you must first c onnec t a terminal 
or a PC with a keyb oard , monitor, and  terminal-emulation software to the d ata 
mod ule. Proc eed  as follows.
1. Connec t one end  of an RS-232 c ab le to an RS-232, serial-c ommunic ations 
p ort (often c alled a COM port) on the terminal or PC. 
2. Connec t the other end  of the RS-232 c ab le to Port 1 of the d ata module
3. If you are using  a PC, start your terminal  emulation software.
Selecting 8400B options
On the 8400B d ata mod ule, all c onfiguration op tions are enab led  b y d efault. You 
c onfig ure the 8400B by d isab ling  op tions with a c od e that you enter in a memory 
reg ister (S24) in the d ata mod ule. Consult the tab le b elow, and  p erform the steps 
that follow. 
Proc eed  as follows.
Table 12. Codes for disabling default settings of the 8400B data module
Default setting Disabling code
With Telep hone1
US Comp and ing2
Telep hone Provides Dialing4
Disab le Data Metering  Feature16
Immed iate Sp eakerp hone Ac tivation32
Automatic  Sp eakerp hone Ac tivation64
Disab le Busyout During  Loc al Loop b ac k Test128
Continued on next page
PHONELINE
POWER
8400b RBP 041196 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Data Modules and Asynchronous Data Units 
72 Connect Data Modules 
4
1. Calc ulate an op tion-selec tion value using  Fig ure  12, ‘‘Codes for disabling 
d efault setting s of the 8400B d ata mod ule’’. Add up the disabling codes 
for all op tions that you wish to d isab le.
For examp le, if you turned  off With Telephone
, US Companding
, Disable 
Data Metering Feature
, the selec tion c od e would  b e: 
1 + 2 + 16 = 19
 
2. Chec k the c urrent d ata-mod ule setting  b y entering  AT S 2 4 ?
.
3. If the c urrent value d oes not matc h the selec tion value you c alc ulated ,  
enter AT S 2 4 =
nnn, where nnn is the selec tion value you c alc ulated .
Configuring the ExpressRoute 1000 Data Module
You c an sub stitute an Exp ressRoute 1000 d ata mod ule for the 8400B d ata 
mod ule. Both DCP and  ISDN-BRI c onnec tions are p ossib le. Fi g u re  1 8
 shows 
typic al c onnec tions.
!CAUTION:
In DC-p owered  c ab inet installations, a 105C Isolator ad ap ter is required  
when c onnec ting  eq uip ment to a d ata mod ule. 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Data Modules and Asynchronous Data Units 
73 Administer the DEFINITY ECS for Data Modules 
4
Figure 18. Typical ExpressRoute 1000 Data Module Connections
Administer the DEFINITY ECS for 
Data Modules
You have to ad minister eac h d ata mod ule that you attac h to the system.
NOTE:
Only the b asic  p roc ed ure is c overed  here. For the full rang e of op tions, see 
the DEFINITY Enterp rise Communic ations Server Release 8 Ad ministrator’s 
Guid e. 
1. Loc ate an availab le p ort. At the DEFINITY ECS ad ministration c onsole, 
enter
list config port 1. To BRI c irc uit p ac k or DCP d ig ital 
line circuit pack
2. Main d istrib ution frame (MDF)
3. Exp ressRoute 1000 d ata mod ule4. PC ad ministration terminal
5. Mod ular line c ord
6. M25B (25-Pin RS-232) c able
cydf008 RPY 123097
PHONELINE
POWER
12
3
4
56 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Data Modules and Asynchronous Data Units 
74 Administer the DEFINITY ECS for Data Modules 
4
Screen 1. Typical system-configuration listing
2. Loc ate an unassig ned  p ort on a suitable c irc uit p ac k, and  make a note of 
the corresponding port number.
The port number is the Board Number
, 
UUCSS (where UU is the 2-d ig it 
c ab inet numb er, 
C is the sing le-c harac ter c arrier id entifier, and  SS is the 
2-d ig it slot numb er) followed  b y the next 2-d ig it numb er, 
PP, in the 
seq uenc e in the Assigned Ports
 field s at the rig ht sid e of the form: 
UUCSSPP.
For examp le, in the listing  ab ove, the next availab le p ort ad d ress for the 
TN2181 d ig ital line c irc uit p ac k would  b e 01A0503
.
3. From the DEFINITY administration c onsole, op en a new d ata-mod ule form 
by typing
add data-module next
 
The system automatic ally assig ns the next availab le  extension numb er to  
the d ata mod ule.  
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Data Modules and Asynchronous Data Units 
75 Asynchronous Data Units (ADUs) 
4
Screen 2. Typical data-module form
4. In the Port
 field, enter the seven-digit port address that you wrote down in 
step  2
, ab ove. 
5. If you installed  a telep hone on the d ata mod ule, enter the extension 
numb er and  station name for this telep hone in the ASSIGNED MEMBER
 
p art of the form.
6. Press the 
F3 key to c lose the form and  save the c hanges.
Asynchronous Data Units (ADUs)
ADUs are used  with Data Line c irc uit p ac ks to c onnec t p erip herals, suc h as 
p rinters, d ata terminals, fax eq uip ment, and  c all-d etail rec ord ing  eq uip ment to 
the DEFINITY. Fi g u re  1 9
 shows a typ ic al Z3A2 ADU assemb ly (without a c ab le). 
n
Ad d  a female-to-male EIA-232 c ab le (shown) to make a Z3A1 ADU 
assemb ly. 
n
Ad d  a female-to-female EIA-232 c ab le (not shown) to make a Z3A4 ADU 
assemb ly. 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Data Modules and Asynchronous Data Units 
76 Asynchronous Data Units (ADUs) 
4
Figure 19. Z3A2 Asynchronous Data Unit (ADU)
Refer to the tab les in Ap p end ix A, ‘‘Connec tor and Cab le Pinout Charts’’
, for the 
p inouts of the TN726B d ata line c irc uit p ac k and  TN2183 analog  line c irc uit p ac k 
(or eq uivalents) in the c ab inet. 1. Z3A2 ADU
2. 25-p in male D-c onnec tor (EIA-232-D) to 
DTE
3. Wall jac k c onnec tor (to d ata line c irc uit 
pac k or analog  line c irc uit p ac k or 
eq uivalent)4. Telep hone jac k (to analog  telep hone)
5. Orig inate/d isc onnec t jac k
6. Female c onnec tor on EIA-232-D c ab le
7. Male c onnec tor on EIA-232-D c ab le
adu KLC 053196 
						

							External Modems 
77 Hardware required when configuring modems 
5
DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
5
External Modems
The following sec tion assumes that you are using  one of the rec ommend ed  
mod ems. However, any loc ally ob tained, type-ap p roved  external mod em should  
work. Contac t your Luc ent Tec hnolog ies rep resentative for more information.
Rec ommend ed  modems inc lud e:
n
Parad yne Comsp here 3715
n
Parad yne Comsp here 3810 Plus and 3811 Plus
n
Parad yne Comsp here 3910
n
U.S. Rob otic s (various mod els)
Hardware required when configuring 
modems
To c onfig ure many mod ems, you use the Hayes-c omp atib le AT c ommand  set. 
Before you c an enter AT c onfig uration c ommand s, you must first c onnec t a 
terminal or a PC with a keyb oard , monitor, and  terminal-emulation software to the 
mod em. Proc eed  as follows.
1. Connec t one end  of an RS-232 c ab le to an RS-232, serial-c ommunic ations 
p ort (often c alled a COM port) on the terminal or PC. 
2. Connec t the other end  of the RS-232 c ab le to the mod em.
3. If you are using  a PC, start your terminal  emulation software. 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
External Modems 
78 PARADYNE COMSPHERE 3715 
5
PARADYNE COMSPHERE 3715 
You c onfig ure COMSPHERE 3715 mod ems using  the Hayes-c omp atib le AT 
c ommand s c ommon to many mod ems. For instruc tions on how to p hysic ally 
c onnec t the mod em and  enter the c ommand s listed  in the instruc tions b elow, see 
the d oc umentation that c ame with the mod em.
Configuring the 3715 for CMS
The instruc tions below set up the modem for use in a DEFINITY ECS Call 
Manag ement System (other c onfig urations may work as well). 
1. From the c ommand line p rompt of your terminal emulation software or 
terminal, enter at&f
.
This load s fac tory d efault c onfig uration options into ac tive memory. If all is 
well, the modem replies OK
.
2. Enter at%b9600
.
This sets the data sp eed to 9600 kb p s. If all is well, the modem rep lies 
OK
.
3. Enter atq1&r0&S1\d1&w0
.
This d isab les result c od es, sets the RTS (Req uest To Send ),  DSR (Data 
Set Read y), CTS (Clear To Send ) sig nals ac tion to stand ard  RS-232 
op eration, and saves the c hang es to p rofile 0
. If all is well, the mod em 
rep lies OK
.
Configuring the 3715 for modem pooling
The instruc tions below set up the modem for use in a DEFINITY modem pool 
(other c onfig urations may work as well). 
1. From the c ommand line p rompt of your terminal emulation software or 
terminal, enter at &f
.  
This load s fac tory d efault c onfig uration options into ac tive memory. If all is 
well, the modem replies OK
.
2. Enter at m0 x7 y0 &s1 /d1
.  
If all is well, the mod em rep lies OK
.
3. Enter at e0 v0 c2=128 s7=60 f10=100 &w0 &y0
.  
If all is well, the mod em rep lies OK
.