Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation For Adjuncts And Peripherals Manual

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
External Modems 
89 Administering the DEFINITY for Modems 
5
3. Set the Adjustable Make/Break Ratio:
 field  to &P0 
for the United  States 
and  Canada, &P1
 for the United  King d om and Hong  Kong. 
Controls the make/b reak ratios of p ulses and  DTMF d ialing . The United  
States and  Canad a use 39% make and  61% b reak. The United  King d om 
and  Hong  Kong  use 33% make and  67% b reak
4. Set the Dial Command:
 field  to D
.
Specifies standard dialing command.
Setting additional, modem-specific parameters
1. Put any remaining  AT c onfig uration c ommand s req uired  b y your mod em in 
the Misc. Init. Param: 
field .
Exiting the form and saving the changes
1. When you are finished , p ress EN TER.  
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
External Modems 
90 Administering the DEFINITY for Modems 
5 
						

							Printers 
91 Configuring the AT&T Model 572 
6
DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
6
Printers
This chapter p rovid es information on config uring  the various p rinters sup p orted  
by Lucent.
Configuring the AT&T Model 572
An AT&T Mod el 572 printer func tions as a CDR devic e, system p rinter, or journal 
p rinter. The op tions are set with func tion keys rather than DIP switc hes. Fig ure  21
 
shows the arrang ement of the func tion keys on the p rinter c ontrol p anel.
Figure 21. Control Panel for 572 Printer1. Power on b utton
2. Alarm b utton
3. Print q uality b utton4. On line b utton
5. Line feed button
6. Form feed  b utton
Powe r
OnAlarm Print
QualityOn
LineLine
FeedFor m
Feed
345162 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Printers 
92 Configuring the AT&T Model 572 
6
Entering Setup Mode
1. Load paper.
2. Turn the Power On
 b utton OFF.
3. Simultaneously p ress and  hold  the Print Quality
 and  On Line
 b uttons.
4. Without releasing  the Print Quality
 and On Line
 b uttons, press the Power 
On
 b utton. 
5. Release all three buttons. 
The p rinter is now in set-up  mod e. It p rints its c urrent setting s. 
Selecting the Correct Configuration for Your 
Application
1. If the p rinter is used  with a PC, as a CDR rep orting devic e, or as a journal 
p rinter, set the op tions as shown in Ta b l e  1 4
. 
Table 14. 572 Printer Used with Management Terminal 
 Function Function Name Menu  Menu Status
01 FORM LENGTH 09 11
02 LPI 01 6
03 CPI 01 10
04 LQ or NLQ 01 LQ
05 BUZZER 01 ON
06 FONT 02 FONTCART
07 RESOLUTION 01 144
1 1 B U FFER 0 2 N - L I N E
13 PW ON MODE 01 ON-LINE
14 DIRECTION 01 B1-DIR.1
15 BUFF FULL 02 LF +  CR
1 6 P. E. 0 1 AC TI VE
17 A UTO  CA RRIA GE RETURN ( CR) 01 CR +  LF
18 ZERO 01 0
22 AUTO LINE FEED 01 CR ONLY
311’’ SKIP 01 OFF
Continued on next page 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Printers 
93 Configuring the AT&T Model 572 
6
2. If the p rinter is used as the system printer, set the op tions as shown in 
Tab le 15
. 3 2 C H A R. SET ( GO ,  GL ) 0 2 U SA
33 CHAR.SET (G1, GR) 01 UK
34 CHAR SET (G2) 03 GE
35 CHAR SET (G3) 07 LINE 
DRAWING
81 OFF-LINE STATE 01 ALL RECEIVE
82 DSR 02 OFF
8 3 REQU EST TO  SEN D  ( RTS) TI M I N G 0 1 RTS
84 CD 02 OFF
8 5 C L EA R TO  SEN D  ( C TS) 0 2 O FF
91 OVER RUN 02 256
92 DATA BIT 02 8
93 PROTOCOL 03 XON/XOFF
94 STOP BIT 01 1
95 PARITY 01 NONE
96 PBS (matc hes c onnec ted  d evic e) 01 9600
Table 15. 572 Printer Used as System Printer
572 Printer Option Settings
Function Function Name Menu Menu Status
01 FORM LENGTH 09 11
02 LPI 01 6
03 CPI 01 10
04 LQ or NLQ 01 LQ
05 BUZZER 01 ON
Continued on next page
Table 14. 572 Printer Used with Management Terminal  — Continued
 Function Function Name Menu  Menu Status
Continued on next page 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Printers 
94 Configuring the AT&T Model 572 
6
06 FONT 02 FONTCART
07 RESOLUTION 01 144
1 1 B U FFER 0 2 N - L I N E
13 PW ON MODE 01 ON-LINE
14 DIRECTION 01 B1-DIR.1
15 BUFF FULL 02 LF +  CR
1 6 P. E. 0 1 A C TI VE
17 A UTO  CA RRIA GE RETURN ( CR) 01 CR +  LF
18 ZERO 01 0
22 AUTO LINE FEED 01 CR ONLY
311’’ SKIP 01 OFF
3 2 C H A R. SET ( GO ,  GL ) 0 2 U SA
33 CHAR.SET (G1, GR) 01 UK
34 CHAR SET (G2) 03 GE
35 CHAR SET (G3) 07 LINE DRAWING
81 OFF-LINE STATE 01 ALL RECEIVE
82 DSR 02 OFF
8 3 REQU EST TO  SEN D  ( RTS) 
TI M I N G01 RTS
84 CD 02 OFF
8 5 C L EA R TO  SEN D  ( C TS) 0 2 O FF
91 OVER RUN 02 256
92 DATA BIT 02 8
93 PROTOCOL 03 XON/XOFF
94 STOP BIT 01 1
95 PARITY 01 NONE
96 PBS 04 1200
Table 15. 572 Printer Used as System Printer
572 Printer Option Settings
Function Function Name Menu Menu Status
Continued on next page 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Printers 
95 Connecting the Printer 
6
Using the Control Panel
1. Use Line Feed
 or Form Feed
 to step  throug h the op tions for the func tion.
2. To ac tivate the menu for the func tion, p ress On Line
. 
3. To step  throug h the op tions for the func tion, p ress Line Feed
 and  Form 
Feed
.
4. When you reac h the op tion you are looking  for, p ress Print Quality
 to 
selec t. 
The p rinter p rints the new setting . Rep eat for eac h op tion to b e set.
5. When finished , p ress Print Quality
. The p rinter c hang es to normal mod e.
Connecting the Printer
Connect the printer using one of the following methods: 
n
An Async hronous Data Unit (ADU) or d ata mod ule (see Chap ter 4, ‘‘Data 
Mod ules and  Asynchronous Data Units’’) 
n
A d irec t, RS-232 c onnec tion from the serial p ort on the p rinter (often 
labeled COM) to the serial port on the DEFINITY ECS (lab led  DCE). 
Okidata Model OP16N
The following sections describe the set-up of the printer and associated interfaces 
used during testing.
Setting Up the OP16N
1.Set up the printer, install toner, and load paper as described in the vendor 
documentation, with one exception: 
fill the p ap er tray until the p ap er 
indic ator g aug e read s PAPER FULL. 
Do not try to load  the full 500 sheets of 20-lb  p ap er ind ic ated  in the 
d oc umentation. The true c ap ac ity is usually ab out 475 sheets. When more 
is load ed , the printer jams.   
Connecting OP16N to CMS
Connecting the OP16N via a parallel port
If the new p rinter is b eing  c onnec ted to CMS throug h the p arallel interfac e, the 
c onnec tivity has not c hang ed .  
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Printers 
96 Okidata Model OP16N 
6
See Fig ure 22, ‘‘Connec ting  the OP16N p rinter to a Sun CMS using  the parallel 
interfac e’’, for an overview of p ossib le OP16N p arallel c onnec tions.
Figure 22. Connecting the OP16N printer to a Sun CMS using the parallel interface
Connecting the OP16N via serial port
The OP16N c omes with a p arallel interfac e only. T
o c onnec t it to a serial p ort, you 
have to use a c onverter. Proc eed  as follows.
1. Attach an OKIDATA Serial Interface Conver ter (part number 50115001) to 
the parallel port on the back of the printer. 
 
2. Connec t the p rinter to a serial p ort on the CMS. 
The following c onnec tions are possible, dep end ing  on the CMS 
eq uip ment you have installed :
n
A serial port on an 8-, 16-, or 64-port NTS (Network Terminal Server) 
installed on a Sun server
n
A serial p ort on an 8- or 16-p ort Aurora Ports Card  installed  on a 
Sun server other than the E3000
n
A serial p ort on an Eq uinox Meg ap lex b ric k installed  on an AT&T 
Intel-based CMS platform
n
 A serial p ort on an IPC-1600 fanout mod ule installed  on an AT&T 
Intel-based CMS platform
See Fig ure 23
, ‘‘Connec ting  the OP16N p rinter to a Sun CMS using  the 
serial c onverter’’, for an overview of possib le OP16N serial c onnec tions. 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Printers 
97 Okidata Model OP16N 
6
Figure 23. Connecting the OP16N printer to a Sun CMS using the serial converter
Figure 24. Connecting the OP16N printer to a Megaplex brick or IPC-1600 fanout 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Printers 
98 Okidata Model OP16N 
6
Administering the OP16N
On Intel CMS systems, in face
, the Printer Type
 for the OP16n is HPLASERJET
. 
On Sun CMS systems, the lpadmin type
 for the OP16N is hplaserjet
.