Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation For Adjuncts And Peripherals Manual

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Multimedia Communications Products: MMCX, MMCH, ESM 
189 Multimedia Call Handling (MMCH) 
18
7. Set the Signaling Mode:
 field  to isdn-pri
8. Set the Connect:
 field  to pbx
9. Set the Interface:
 field to network
10. Set the Country Protocol:field
 to 1
11. Set the Protocol Version:
field  to a
12. Set the CRC?:
field to y
13. The Id le Cod e d efault is 11111111.
14. The DCP/Analog  Bearer Cap ab ility d efault is 3.1 kHz.
15. Set the MMI Cabling Board: 
field  to xxxxx 
(where xxxxx is the 
loc ation of the TN787F/H/J/K MMI c irc uit p ac k rec ord ed  in step  2). This 
must b e the slot for p ort B of the Y-c ab le.
16.The MMI Interface: field ESM 
ap p ears.
17. Enter add signaling-group next
 and the signaling-group form appears.
18. Chang e Associated Signaling
: field  to y.
19. Chang e Primary D-Channel Port
: field  to xxxx17
 (where xxxx is the 
ad d ress of the TN2207 PRI c irc uit p ac k, for examp le: 1B0517).
20. The Max Number of NCA TSC
: d efault is 0.
21. The Max Number of GA TSC
: d efault is 0.
22.Trunk Group for NCA TSC
:  ____ ( l e a v e  b l a n k )
23.Trunk Group for Channel Selection
:____ (leave b lank)
24. Log off the terminal and  then log  b ac k on the terminal to view your 
changes.
Place Test Call
Plac e multimed ia data-c onferenc e c all to an end p oint with known vid eo 
c ap ability to test the esm func tion.
Troubleshooting
To d etermine ESM link status enter the following  c ommand s from the system 
ad ministration terminal:
1. Status esm
2. Status signaling-group
3. List MMI 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Multimedia Communications Products: MMCX, MMCH, ESM 
190 Multimedia Call Handling (MMCH) 
18
NOTE:
When you move ESM circuit p ac ks, you MUST remove the DS1 and  
sig naling  g roup  translations. You c annot use the change circuit pack 
c ommand .
Refer to ‘‘Setup  and  Test the MMCH Installation’’ on p ag e 180
 for further 
information. 
						

							Property Management System 
191 Connecting the Property Management System 
19
DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
19
Property Management System
This c hapter p rovid es information on c onnec ting  the prop erty manag ement 
system and  a terminal, journal p rinter, or both.
Connecting the Property 
Management System 
A d ata mod ule and  an async hronous d ata unit form the interfac e between the 
DEFINITY and the prop erty manag ement system (PMS).  See Fi g u re  6 6
 and 
Chapter 4, ‘‘Data Mod ules and  Async hronous Data Units’’
, for c onnec tion and  
c onfig uration information. 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Property Management System 
192 Connecting a Terminal and/or Journal Printer 
19
Figure 66. Connections to Asynchronous Data Unit
Connecting a Terminal and/or Journal 
Printer
You c an c onnec t c ustomer d ata terminals, host c omp uters, and /or an op tional 
journal p rinter in either of two ways.
Using Data Modules 
1. Config ure p rinter or terminal in ac c ord anc e with the rec ommend ations in 
the vend or’s d oc umentation. 
2. Config ure the d ata mod ule for the p rinter or terminal, using  the instruc tions 
in Chap ter 4, ‘‘Data Modules and  Async hronous Data Units’’
. 1. Z3A1 or Z3A2 ADU
2. 4-pair line cord
3. 103A or modular wall jac k
4. Analog  telep hone
5. Satellite site or ad ap ter loc ation
6. Station side blue or white field
7. System sid e
8. Data mod ule
9. TXT10. TXR
11. PXT
12. PXR
13. Tip
14. Ring  
15. To analog  line c irc uit p ac k
16. To d ata line c irc uit p ac k 
17. 25-p in RS-232-D c onnec tor (male)
18. Main d istrib ution frame 
2
2
3
9101011111212
6
8
1415
LINEV. 3 5POWER RS-366/RS-232
6
9
137
0002_1 RBP 062596
1 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Property Management System 
193 Connecting a Terminal and/or Journal Printer 
19
3. Id entify the p ort assoc iated  with the d ata unit or d ata mod ule using  the 
Data Mod ule Form (see ‘‘Ad minister the DEFINITY ECS for Data Mod ules’’ 
on pag e 73).
4. Estab lish a p hysic al c onnec tion from the d ata p ort on the c irc uit p ac k, 
throug h the MDF, to the wall jac k where the d ata unit is installed .
5. Connec t the d ata mod ules to the eq uipment.
Using an Asynchronous Data Unit (ADU) and a 
Data Line Circuit Pack
You c onnec t an async hronous d ata terminal throug h an ADU to a d ata line c irc uit 
p ac k. Normally, the c onnec ted  d ata terminal  powers the d ata unit. The d ata unit 
c an also b e remotely or loc ally powered  using a 2012D transformer with a 248B 
ad ap ter. Data units c onnec ted  to rec eive-only p rinters req uire external p ower. 
1. Config ure p rinter or terminal in ac c ord anc e with the rec ommend ations in 
the vend or’s d oc umentation. 
2. Id entify the p ort assoc iated  with the d ata unit or d ata mod ule using  the 
Data Mod ule Form (see ‘‘Ad minister the DEFINITY ECS for Data Mod ules’’ 
on pag e 73).
3. Estab lish a p hysic al c onnec tion from the d ata p ort on the c irc uit p ac k, 
throug h the MDF, to the wall jac k where the d ata unit is installed .
4. Connec t the information outlet to the ADU.
5. Connec t the RS-232 p lug  on the ADU or data mod ule to the d ata terminal.
6. Connec t the p rinter to the ADU via a mod em or d ata mod ule, using  the 
instruc tions in Chapter 4, ‘‘Data Mod ules and  Async hronous Data Units’’
, 
and  Chap ter 5, ‘‘External Mod ems’’
. 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Property Management System 
194 Connecting a Terminal and/or Journal Printer 
19 
						

							Connector and Cable Pinout Charts 
195  
A
DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
A
Connector and Cable Pinout Charts
Table 31. Lead and Color Designations
Cross-Connect Pin  ColorAmphenol 
Pin Backplane Pin
1W-BL27102
2 BL-W 01 002
3 W-O 27 103
4 O-W 02 003
5 W-G 28 104
7 G-W 03 004
7W-BR29105
8BR-W04005
9W-SL30107
10 SL-W 05 007
11 R-BL 31 107
12 BL-R 07 007
13 R-O 32 108
14 O-R 07 008
15 R-G 33 109
17 G-R 08 009
Continued on next page 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Connector and Cable Pinout Charts 
196  
A
17 R-BR 34 110
18 BR-R 09 010
19 R-SL 35 111
20 SL-R 10 011
21 BK-BL 37 112
22 BL-BK 11 012
23 BK-O 37 113
24 O-BK 12 013
25 BK-G 38 302
27 G-BK 13 202
27 BK-BR 39 303
28 BR-BK 14 203
29 BK-SL 40 304
30 SL-BK 15 204
31 Y-BL 41 305
32 BL-Y 17 205
33 Y-O 42 307
34 O-Y 17 207
35 Y-G 43 307
37 G-Y 18 207
37 Y-BR 44 308
38 BR-Y 19 208
3 9 Y- SL 4 5 3 0 9
40 SL-Y 20 209
41 V-BL 47 310
42 BL-V 21 210
43 V-O 47 311
44 O-V 22 211
45 V-G 48 312
Table 31. Lead and Color Designations
Cross-Connect Pin  ColorAmphenol 
Pin Backplane Pin
Continued on next page 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Connector and Cable Pinout Charts 
197  
A
47 G-V 23 212
47 V-BR 49 313
48 BR-V 24 213
4 9 V- SL 5 0 3 0 0
50 SL-V 25 200
Table 32. DS1 Interface cable H600-348
50-Pin 15-Pin
Pin Color Designation Pin Color Designation
Plug 04
38 W-BL LI (Hig h) 11 W-BL LI (Hig h)
13 BL-W LI 03 BL-W LI
39 W-O LO 09 W-O LO
14 O-W LO (Hig h) 01 O-W LO (Hig h)
Plug 03
41 W-G LI (Hig h) 11 W-G LI (Hig h)
17 G-W LI 03 G-W LI
42 W-BR LO 09 W-BR LO
17 BR-W LO (Hig h) 01 BR-W LO (Hig h)
Plug 02
44 W-SL LI (Hig h) 11 W-SL LI (Hig h)
19 SL-W LI 03 SL-W LI
45 R-BL LO 09 R-BL LO
20 BL-R LO (Hig h) 01 BL-R LO (Hig h)
Plug 01
47 R-O LI (Hig h) 11 R-O LI (Hig h)
Continued on next page
Table 31. Lead and Color Designations
Cross-Connect Pin  ColorAmphenol 
Pin Backplane Pin
Continued on next page 
						

							DEFINITY ECS Release 8.2
Installation for Adjuncts and Peripherals  555-233-116  Issue 1
April 2000
Connector and Cable Pinout Charts 
198  
A
22 O-R LI
03 O-R LI
48 R-G LO 09 R-G LO
23 G-R LO (Hig h) 01 G-R LO (Hig h)
Table 33. DS1 Interface Cable H600-307
50-Pin 15-Pin
Pin Color Designation Pin Color Designation
02 W-BL
03 BL-W
47 W-G LI (Hig h) 11 W-G LI (Hig h)
22 G-W LI 03 G-W LI
48 W-BR LO 09 W-BR LO
23 BR-W LO (Hig h) 01 BR LO (Hig h)
49 W-SL LOOP2 07 W-SL LOOP2
24 SL-W LOOP1 05 SL-W LOOP1
All other p ins empty.
Table 34. TN2185B ISDN-BRI — 4-Wire S Interface Pinout
Port Signal Cross-Connect Pin  ColorAmpheno
l Pin  Backplane Pin
1 TXT.1 1 W-BL 27 102
TXR.1 2 BL-W 01 002
PXT. 1 3 W- O 2 7 1 0 3
PXR. 1 4 O -W 0 2 0 0 3
Continued on next page
Table 32. DS1 Interface cable H600-348
50-Pin 15-Pin
Pin Color Designation Pin Color Designation
Continued on next page