Konica Minolta Di2011 User Manual

							33.1 Making Copies
3-2 Di1611/Di2011
Basic Operations
Chapter 3
3.1 Making Copies
The following procedure describes how to load a document and make a simple 
copy of it.
To make a simple copy
1Load the document to be copied.
❍Refer to “Loading the Document” on page 3-9.
2Select the desired copy settings.
❍Paper (p. 5-22)
❍Zoom (p. 5-30)
❍Copy density (p. 5-36)
❍Advanced Copy Operations 
(p. 6-1)
3Using the 10-Key Pad, enter the 
desired number of copies.
❍The number of copies can be set 
to any number between 1 and 99.
❍To clear the entered value, press 
the [No] key.
Downloaded From ManualsPrinter.com Manuals 
						

							3.1 Making Copies3
Di1611/Di2011 3-3
Basic Operations
Chapter 3
4Press the [Start] key.
The set number of copies are made. 
❍To stop copying before the set 
number of copies have been 
made, press the [Stop] key.
Downloaded From ManualsPrinter.com Manuals 
						

							33.2 Loading Paper
3-4 Di1611/Di2011
Basic Operations
Chapter 3
3.2 Loading Paper
While loading paper, be sure to observe the following precautions.
If the paper is curled, flatten it before 
loading it.
Do not load so much paper that the 
top of the stack is higher than 
the mark or exceeds the specified 
number of sheets.
Make sure that the paper guides are 
pushed up against the edges of the 
paper.
✎
Tip
We recommend replenishing the paper only after all of the paper in the drawer 
has been used.
Downloaded From ManualsPrinter.com Manuals 
						

							3.2 Loading Paper3
Di1611/Di2011 3-5
Basic Operations
Chapter 3
Loading Paper Into the Paper Tray
To load paper into the 1st Tray
1Pull out the 1st Tray.
?Have the necessary precautions 
been observed when pulling out 
the tray?
➜Be careful not to touch the surface 
of the Paper Take-up Roller with 
your hands.
2Press down on the Paper-Lifting Plate 
until it locks into place.
3Load the paper into the tray so that the 
front side of the paper (the side facing 
up when the package was 
unwrapped) faces up.
?Have the necessary precautions 
been observed when loading the 
paper?
➜Do not load so much paper that 
the top of the stack is higher than 
the  mark.
Paper Take-up Roller
Paper-Lifting Plate
Downloaded From ManualsPrinter.com Manuals 
						

							33.2 Loading Paper
3-6 Di1611/Di2011
Basic Operations
Chapter 3
4Slide the paper guides against the 
edges of the paper.
?Is the paper guide positioned 
correctly?
➜Make sure that the paper guides 
are pushed up against the edges 
of the paper.
5Close the 1st Tray.
Downloaded From ManualsPrinter.com Manuals 
						

							3.2 Loading Paper3
Di1611/Di2011 3-7
Basic Operations
Chapter 3
To load paper into the 2nd Tray
Load paper into the 3rd, 4th and 5th paper trays using the same procedure 
described below.
1Pull out the 2nd Tray.
2Press down on the Paper-Lifting Plate 
until it locks into place.
3Load the paper into the tray so that the 
front side of the paper (the side facing 
up when the package was 
unwrapped) faces up.
?Have the necessary precautions 
been observed when loading the 
paper?
➜Do not load so much paper that 
the top of the stack is higher than 
the mark.
Paper-Lifting Plate
Downloaded From ManualsPrinter.com Manuals 
						

							33.2 Loading Paper
3-8 Di1611/Di2011
Basic Operations
Chapter 3
4Slide the paper guides against the 
edges of the paper.
?Is the paper guide positioned 
correctly?
➜Make sure that the paper guides 
are pushed up against the edges 
of the paper.
5Close the 2nd Tray.
Downloaded From ManualsPrinter.com Manuals 
						

							3.3 Loading the Document3
Di1611/Di2011 3-9
Basic Operations
Chapter 3
3.3 Loading the Document
The document can be loaded into the Document Feeder (optional) or positioned on 
the Original Glass. Position the document correctly according to the type of 
document being copied.
With the Document Feeder
1Slide out the Document Guide Plates.
2Load the document pages to be 
copied face up into the Document 
Feeder.
?Have the necessary precautions 
been observed when loading the 
document?
➜A maximum of 50 document 
pages can be loaded. (With AF-
12)
➜A maximum of 80 document 
pages can be loaded. (With AFR-19)
➜Do not load so many pages that the top of the stack is higher than 
the mark.
3Adjust the Document Guide Plates to 
fit the size of the document.
✎
Note
Be sure to load the document 
correctly, otherwise the pages 
may not be fed in straight.
Downloaded From ManualsPrinter.com Manuals 
						

							33.3 Loading the Document
3-10 Di1611/Di2011
Basic Operations
Chapter 3
4If necessary, specify any other copy settings.
❍Before Making Copies (p. 5-1)
❍Advanced Copy Operations (p. 6-1)
5Press the [Start] key.
Downloaded From ManualsPrinter.com Manuals 
						

							3.3 Loading the Document3
Di1611/Di2011 3-11
Basic Operations
Chapter 3
With the Original Glass
To position sheet documents
For plain documents or documents that cannot be loaded into the Automatic 
Document Feeder, position them as described below.
1Lift open the Original Cover, or the Document Feeder if it is installed.
2Position the document to be copied 
face down on the Original Glass.
❍Align the document on the scales 
above and to the left of the Original 
Glass.
3Carefully close the Original Cover, or the Automatic Document Feeder if it is 
installed.
4If necessary, specify any other copy settings.
❍Before Making Copies (p. 5-1)
❍Advanced Copy Operations (p. 6-1)
Downloaded From ManualsPrinter.com Manuals