Konica Minolta Di2011 User Manual

							11.5 Safety Information
1-12 Di1611/Di2011
Introduction
Chapter 1
CDRH Regulation
This machine is certified as a Class 1 Laser product under Radiation Performance 
Standard according to the Food, Drug and Cosmetic Act of 1990. Compliance is 
mandatory for Laser products marketed in the United States and is reported to the 
Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug 
Administration of the U.S. Department of Health and Human Services (DHHS). This 
means that the device does not produce hazardous laser radiation.
The label shown on page 1-14 indicates compliance with the CDRH regulations and 
must be attached to laser products marketed in the United States.
This is a semiconductor laser. The maximum power of the laser diode is 5 mW and 
the wavelength is 770-795 nm.
For European Users
This is a semiconductor laser. The maximum power of the laser diode is 5mW and 
the wavelength is 770-795 nm.
For Denmark Users
Dansk: Dette er en halvlederlaser. Laserdiodens højeste styrke er 5mW og 
bølgelængden er 770-795 nm.
For Finland, Sweden UsersCAUTION
Use of controls, adjustments or performance of procedures other than those 
specified in this manual may result in hazardous radiation exposure.
CAUTION
Use of controls, adjustments or performance of procedures other than those 
specified in this manual may result in hazardous radiation exposure.
ADVARSEL
Usynlig laserstråling ved åbning, når sikkerhedsafbrydere er ude af funktion. 
Undgå udsættelse for stråling. Klasse 1 laser produkt der opfylder IEC60825 
sikkerheds kravene.
LOUKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
VAROITUS!
Laitteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa 
altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
Downloaded From ManualsPrinter.com Manuals 
						

							1.5 Safety Information1
Di1611/Di2011 1-13
Introduction
Chapter 1
Tämä on puolijohdelaser. Laserdiodin sunrin teho on 5mW ja aallonpituus on 770-
795 nm.
Det här är en halvledarlaser. Den maximala effekten för laserdioden är 5mW och 
våglängden är 770-795 nm.
For Norway Users
Dette en halvleder laser. Maksimal effekt till laserdiode er 5mW og bølgelengde er 
770-795 nm.VARNING!
Om apparaten används på annat sätt än i denna bruksanvisning specificerats, 
kan användaren utsättas för osynlig laserstrålning, som överskrider gränsen för 
laserklass 1.
VARO!
Avattaessa ja suojalukitus ohitettaessa olet alttiina näkymättömälle 
lasersäteilylle. Älä katso säteeseen.
VARNING!
Osynlig laserstrålning när denna del är öppnad och spärren är urkopplad. 
Betrakta ej strålen.
ADVERSEL
Dersom apparatet brukes på annen måte enn spesifisert i denne bruksanvisning, 
kan brukeren utsettes for unsynlig laserstråling som overskrider grensen for laser 
klass 1.
Downloaded From ManualsPrinter.com Manuals 
						

							11.5 Safety Information
1-14 Di1611/Di2011
Introduction
Chapter 1
Laser Safety Label
A laser safety label is attached to the outside of the machine as shown below.
Ozone Release
CAUTION
Locate the Machine in a Well Ventilated Room
➜A negligible amount of ozone is generated during normal operation of this 
machine. An unpleasant odor may, however, be created in poorly ventilated 
rooms during extensive machine operations. For a comfortable, healthy, and 
safe operating environment, it is recommended that the room well ventilated.
REMARQUE
= Placer l’appareil dans une pièce largement ventilée =
Une quantité d’ozone négligable est dégagée pendant le fonctionnement de 
l’appareil quand celui-ci est utilisé normalement. Cependant, une odeur 
désagréable peut être ressentie dans les pièces dont l’aération est insuffisante et 
lorsque une utilisation prolongée de l’appareil est effectuée. Pour avoir la 
certitude de travailler dans un environnement réunissant des conditions de 
confort, santé et de sécurité, il est préférable de bien aérer la pièce ou se trouve 
l’appareil.
Downloaded From ManualsPrinter.com Manuals 
						

							1.5 Safety Information1
Di1611/Di2011 1-15
Introduction
Chapter 1
Acoustic Noise
For European Users
Machine Noise Regulation 3 GSGV, 18.01.1991 : The sound pressure level at the 
operator position according to EN 27779 is equal to or less than 70dB(A).
Downloaded From ManualsPrinter.com Manuals 
						

							11.5 Safety Information
1-16 Di1611/Di2011
Introduction
Chapter 1
Downloaded From ManualsPrinter.com Manuals 
						

							Precautions
Chapter 2
2
2Precautions
Downloaded From ManualsPrinter.com Manuals 
						

							22.1 Installation Precautions
2-2 Di1611/Di2011
Precautions
Chapter 2
2.1 Installation Precautions
Installation Site
To ensure utmost safety and prevent possible malfunctions, install the machine in 
a location that meets the following requirements.
-A location away from curtains, etc. that may catch fire and burn easily
-A location that is not exposed to water or other liquids
-A location free from direct sunlight
-A location out of the direct airflow of an air conditioner or heater, and not 
exposed to extremely high or low temperatures
-A well-ventilated location
-A location that is not exposed to high humidity
-A location that is not extremely dusty
-A location not subjected to undue vibrations
-A stable and level location
-A location where ammonia or other organic gases are not generated
-A location that does not put the operator in the direct airflow of exhaust from the 
machine
-A location that is not near any kind of heating devices
Power Source
The power source requirements are as follows.
Voltage fluctuation: Maximum ±10%
Frequency fluctuation: Maximum ±3 Hz
❍Use a power source with as little voltage or frequency fluctuations as possible.
Downloaded From ManualsPrinter.com Manuals 
						

							2.1 Installation Precautions2
Di1611/Di2011 2-3
Precautions
Chapter 2
Space Requirements
To ensure easy machine operation, supply replacement, and maintenance, adhere 
to the recommended space requirements detailed below.
✎
Note
Since there is a ventilation duct on the left side of the machine, be sure to allow 
a clearance of *100 mm or more on the left side.
Allow a clearance of **400 mm or more on the right side of the machine so that 
the side cover can be opened.

Unit: mm 5991024 1099
*100
**400
356
995
1069
1100
1099
**400 599
1352
252
356 *100
Downloaded From ManualsPrinter.com Manuals 
						

							22.2 Operation Precautions
2-4 Di1611/Di2011
Precautions
Chapter 2
2.2 Operation Precautions
Operating Environment
The environmental requirements for correct operation of the machine are as 
follows.
Temperature: 10°C to 30°C with fluctuations of no more than 10°C within an 
hour
Humidity: 15% to 85% with fluctuations of no more than 10% within an hour
Proper Use
To ensure the optimum performance of the machine, follow the precautions listed 
below.
-Never place heavy objects on the original glass or subject it to shocks.
-Never open any machine doors or turn off the machine while it is making copies; 
otherwise, a paper jam will occur.
-Never bring any magnetized object or use flammable sprays or liquids near the 
machine.
✚Always make sure that the power plug is completely plugged into the electrical 
outlet.
-Always make sure that the machine’s power plug is visible and not hidden by 
the machine.
✚Always unplug the machine from the electrical outlet if the unit is not to be used 
for a long period of time.
✚Always provide good ventilation when making a large number of continuous 
copies.
Downloaded From ManualsPrinter.com Manuals 
						

							2.2 Operation Precautions2
Di1611/Di2011 2-5
Precautions
Chapter 2
CAUTION
If the ventilation duct on the left side of the machine is blocked, the inside of 
the machine will accumulate heat, resulting in a malfunction or fire.
➜Be sure to allow a clearance of 100 mm or more on the left side of the machine 
for the ventilation duct.
CAUTION
The area around the fusing unit is extremely hot.
➜Be careful not to touch any parts around the fusing unit, other than those 
indicated in this manual, in order to reduce the risk of burns. Be especially 
careful not to touch parts marked with warning labels, and their surrounding 
areas.
➜If you get burnt, immediately cool the skin under cold water, and then seek 
professional medical advice.
Transporting the Machine
If you need to transport the machine over a long distance, consult your technical 
representative.
Care of Machine Supplies
Use the following precautions when handling the machine supplies (toner cartridge, 
paper, etc.).
✚Store the supplies in a location that meets the following requirements.
Free from direct sunlight
Away from any heating apparatus
Not subjected to high humidity
Not extremely dusty
✚Store in a sealed plastic bag in a cool, dark place paper that has been removed 
from its wrapper but not loaded into the machine.
-Only use toner that has been manufactured specifically for this machine. Never 
use other types of toner.
-Keep all supplies out of the reach of children.
Downloaded From ManualsPrinter.com Manuals