Konica Minolta Di2011 User Manual

							55.4 Making Copies on Manually Fed Paper
5-12 Di1611/Di2011
Before Making Copies
Chapter 5
To load envelopes
Load the paper into the Manual Bypass one sheet at a time.
Up to 10 sheets of paper can be loaded into the Multiple Bypass.
➜When loading envelopes, load them with the flap facing up, as shown in the 
illustration.
✎
Note
Before loading envelopes, press them down to make sure that all air is removed, 
and make sure that the folds of the flaps are firmly pressed, otherwise the 
envelopes may become wrinkled or a paper misfeed may occur.
After you have loaded the envelopes, use the control panel to specify the paper 
size and paper type for the Bypass Tray.
Downloaded From ManualsPrinter.com Manuals 
						

							5.4 Making Copies on Manually Fed Paper5
Di1611/Di2011 5-13
Before Making Copies
Chapter 5
✎
Note
Do not load envelopes crosswise.
Do not load envelopes with the flap facing down.
Do not load envelopes with the flap facing backwards.
Downloaded From ManualsPrinter.com Manuals 
						

							55.4 Making Copies on Manually Fed Paper
5-14 Di1611/Di2011
Before Making Copies
Chapter 5
To load OHP transparencies
Load the paper into the Manual Bypass one sheet at a time.
Up to 20 sheets of paper can be loaded into the Multiple Bypass.
➜When loading OHP transparencies, load them in the same orientation as the 
document.
✎
Note
After you have loaded the transparencies, use the control panel to specify the 
paper size and paper type for the Bypass Tray.
Downloaded From ManualsPrinter.com Manuals 
						

							5.4 Making Copies on Manually Fed Paper5
Di1611/Di2011 5-15
Before Making Copies
Chapter 5
To load label sheets
Load the paper into the Manual Bypass one sheet at a time.
Up to 20 sheets of paper can be loaded into the Multiple Bypass.
➜When loading label sheets, load them in the same orientation as the document.
Place documents with the side to be printed facing down.
✎
Note
After you have loaded the label sheets, use the control panel to specify the 
paper size and paper type for the Bypass Tray.
Downloaded From ManualsPrinter.com Manuals 
						

							55.4 Making Copies on Manually Fed Paper
5-16 Di1611/Di2011
Before Making Copies
Chapter 5
Copying Onto Manually Fed Paper
To copy using the Manual Bypass
1Load the document to be copied.
❍Refer to “Loading the Document” on page 3-9.
2Adjust the paper guides to fit the size 
of the paper.
3Insert one sheet of paper with the front 
side facing down, lightly sliding the 
paper as much as possible into the 
feed slot.
The manual bypass mark ( ) 
appears in the bottom line of the 
screen.
?Is a card or a postcard loaded?
➜Make sure that it is not curled 
(rolled).
4Press the [No] key.
The “PAPER SOURCE SETUP” menu appears.
5Use the and keys to select 
the type of paper loaded.
❍Select from the following four 
paper type settings.
“PLAIN”
“OHP”
“CARD”
“ENVELOPE”
6Press the [Yes] key.
The “PAPER SIZE” menu appears.
Downloaded From ManualsPrinter.com Manuals 
						

							5.4 Making Copies on Manually Fed Paper5
Di1611/Di2011 5-17
Before Making Copies
Chapter 5
7Using the and keys, select 
the size of the paper loaded.
❍If “OHP” was selected in step 5, 
select from the following four 
paper size settings.
“A4 L”
“A4 C”
“Letter L”
“Letter C”
❍If paper with a non-standard size is 
loaded, press the key, and 
then use the 10-Key Pad to enter 
the paper size. (For details, refer 
to “To copy onto label sheets” on 
page 4-8.)
?Do you know the size of FLS 
paper?
➜The default FLS size is 210 mm × 330 mm. To change the FLS size, contact 
your service representative.
8Press the [Yes] key.
The main screen appears.
9If necessary, specify any other copy settings.
❍Zoom (p. 5-30)
❍Copy density (p. 5-36)
❍Advanced Copy Operations (p. 6-1)
10Press the [Start] key.
Downloaded From ManualsPrinter.com Manuals 
						

							55.4 Making Copies on Manually Fed Paper
5-18 Di1611/Di2011
Before Making Copies
Chapter 5
✎
Tip
To copy onto more pages using the same settings, feed paper into the Manual 
Bypass to begin making copies automatically.
To make continuous copies onto cards, postcards, OHP transparencies or 
envelopes, load them into the 1st Tray.
If paper other than plain paper is specified and the Manual Bypass is used, the 
screen changes as shown below.
Cards OHP transparencies
Postcards or envelopes
Downloaded From ManualsPrinter.com Manuals 
						

							5.4 Making Copies on Manually Fed Paper5
Di1611/Di2011 5-19
Before Making Copies
Chapter 5
To copy using the Multiple Bypass
1Load the document to be copied.
❍Refer to “Loading the Document” on page 3-9.
2Adjust the Bypass Tray Extender and 
the paper guides to fit the size of the 
paper.
3Load the paper with the front side 
facing down, lightly sliding the paper 
as much as possible into the feed slot. 
The manual bypass mark ( ) 
appears in the bottom line of the 
screen.
?Are sheets of cards or postcards 
loaded?
➜Make sure that they are not curled 
(rolled).
4Check that “YES/NO” appears in the 
bottom line of the screen, and then 
press the [No] key.
The “PAPER SOURCE SETUP” 
menu appears.
✎
Note
“YES/NO” is displayed for approximately 5 seconds after paper is loaded 
into the Multiple Bypass.
5Use the and keys to select 
the type of paper loaded.
❍Select from the following four 
paper type settings.
“PLAIN”
“OHP”
“CARD”
“ENVELOPE”
Downloaded From ManualsPrinter.com Manuals 
						

							55.4 Making Copies on Manually Fed Paper
5-20 Di1611/Di2011
Before Making Copies
Chapter 5
6Press the [Yes] key.
The PAPER SIZE menu appears.
7Using the and keys, select 
the size of the paper loaded.
❍If “OHP” was selected in step 5, 
select from the following four 
paper size settings.
“A4 L”
“A4 C”
“Letter L”
“Letter C”
❍If paper with a non-standard size is 
loaded, press the key 
(“CUSTOM”), and then use the 10-
Key Pad to enter the paper size. 
(For details, refer to “Copying 
Onto Various Types of Media” on 
page 4-6.)
?Do you know the size of FLS 
paper?
➜The default FLS size is 210 mm × 
330 mm. To change the FLS size, contact your service representative.
8Press the [Yes] key.
The main screen appears.
9If necessary, specify any other copy settings.
❍Zoom (p. 5-30)
❍Copy density (p. 5-36)
❍Advanced Copy Operations (p. 6-1)
10Press the [Start] key.
Downloaded From ManualsPrinter.com Manuals 
						

							5.4 Making Copies on Manually Fed Paper5
Di1611/Di2011 5-21
Before Making Copies
Chapter 5
✎
Tip
If paper other than plain paper is specified and the Multiple Bypass is used, the 
screen changes as shown below.
Cards OHP transparencies
Postcards or envelopes
Downloaded From ManualsPrinter.com Manuals