Konica Minolta Di2011 User Manual

							22.5 Part Names and Their Functions
2-16 Di1611/Di2011
Precautions
Chapter 2
Job Separator (Optional)
No.Part NameDescription
12 Copy Tray Lamp Lights up when paper is fed into the Upper Copy Tray.
13 Upper Copy Tray Collects computer printouts.
14 Lower Copy Tray Collects copies.
With the Job Separator installed
12
13
14
Downloaded From ManualsPrinter.com Manuals 
						

							2.6 Names of Control Panel Parts and Their Functions2
Di1611/Di2011 2-17
Precautions
Chapter 2
2.6 Names of Control Panel Parts and Their Functions
Control Panel Parts and Their Functions
No.Part NameFunction
1“Error” indicator Flashes when an error has occurred.
Refer to “Error Messages” on page 8-1.
2 [Printer] key/indicator Lights up while data is being printed from the computer and 
flashes while data is being sent.
For details, refer to the Printer Controller User Manual.
3 [Status] key Used to view the counters.
4 [Utility] key Used to enter Utility mode and display the first Utility mode 
screen.
MACHINE SETTING, PAPER SOURCE SETUP, USER 
MANAGEMENT, 
ADMIN. MANAGEMENT, COPY SETTING 1 & 2
5 Display Displays setting menus, error messages, and specified settings 
such as the number of copies and the zoom ratio.
6 [No] key Erases the entered numbers and letters.
Returns to the previous screen.
7 [Yes] key Confirms the current setting.
8 [Auto Paper/Auto Size] key Used to select between the Auto Paper or the Auto Size 
function.
9 [Zoom] key, and keysUsed to select a preset enlargement or reduction ratio.
With each press, a zoom ratio between 
×0.50 and ×2.00 is 
selected in 0.01 increments.
Used to specify the selection above or below in setting 
screens and menus.
10 [Paper] key Used to select the size of the paper to be printed on.
57 46
18
810 1213141516173
21
19
20
911
Downloaded From ManualsPrinter.com Manuals 
						

							22.6 Names of Control Panel Parts and Their Functions
2-18 Di1611/Di2011
Precautions
Chapter 2
11 [Auto/Photo] 
key, and keysUsed to specify the scanning density of copies.
Used to specify the selection at the left or right in setting 
screens.
12 [Erase] key Used to select the area of the document that is erased.
13 [File Margin] key Press to select the “File Margin” function.
14 [Finishing] key Used to select a copy “Finishing” function.
15 [X/Y  Zoom] key Used to specify different scaling proportions for the vertical and 
horizontal directions.
16 [Neg. Pos.] key Press to make copies with the dark- and light-colored areas of 
the document inverted.
17 Copy  key Used to select between the “2in1” and the “4in1” copy functions.
18 [Copy Program] keyCopy programs can be stored.
Stored copy programs can be selected and recalled.
19 [Book Separation] key Used to select the “Book Separation” function.
20 [Original] key Used to select between the “Duplex Orig.” function and the 
“Mixed Orig.” function.
No.Part NameFunction
Downloaded From ManualsPrinter.com Manuals 
						

							2.6 Names of Control Panel Parts and Their Functions2
Di1611/Di2011 2-19
Precautions
Chapter 2
No.Part NameFunction
21 Scan key Press to enter Scan mode. The indicator lights up in green to 
indicate that the machine is in Scan mode.
(Available only when the Network Interface Card NC-6 and the 
Internet Fax & Network Scan Kit SU-6 are installed.)
22 Fax key Does not function on this machine.
23 Copy key Press to enter Copy mode. The indicator lights up in green to 
indicate that the machine is in Copy mode.
24 Access key Used with user management. (p. 6-23)
25 Energy Save key Press to enter Energy Save mode. (p. 2-23)
26 Interrupt key Press to enter Interrupt mode. The indicator lights up in green 
to indicate that the machine is in Interrupt mode.
Press again to cancel Interrupt mode and return to the mode 
before Interrupt mode was entered. (p. 5-38)
27 [123/ABC] key Does not function on this machine.
28 Panel Reset keyCancels all copy functions and returns them to their default 
settings.
Deletes all queued jobs.
29 Stop key Stops the multi-page copy operation.
30 Start keyStarts copying.
Queues a copy job if pressed while the machine is warming 
up. (p. 2-24)
The indicator lights up in green to indicate that the machine 
is ready to start copying, or it lights up in orange to indicate 
that the machine is not ready to start copying.
31 10-Key PadUsed to specify the number of copies.
Used to enter setting values.
The [ ] and [#] keys do not function on this machine.
212223
24
25
26
27
28293031
Downloaded From ManualsPrinter.com Manuals 
						

							22.6 Names of Control Panel Parts and Their Functions
2-20 Di1611/Di2011
Precautions
Chapter 2
Display Indications
1
2
6
7
54
3 

No.Display IndicationDescription
1 Copy density (document 
type)Indicates the document type for the copy density setting.
“PHOTO”, “TEXT”, or “TEXT/P”
2 Copy density (density level) Indicates the density level for the copy density setting.
3 Paper source Indicates the selected paper tray. If special paper is selected, 
the paper type is displayed.
“AUTO”, a paper tray and paper size, or paper type
4 Number of copies Indicates the specified number of copies.
5 Zoom ratio Indicates the current zoom ratio setting.
“AUTO” or the current zoom ratio setting is displayed. “
×[X/Y]” 
indicates that the “X/Y Zoom” function is selected.
6 Menu or function nameDisplays the current menu, function or settings.
Error messages are displayed when errors occur.
7 Messages Displays messages such as operating instructions.
Downloaded From ManualsPrinter.com Manuals 
						

							2.6 Names of Control Panel Parts and Their Functions2
Di1611/Di2011 2-21
Precautions
Chapter 2
Adjusting the Angle of the Display
The display can be adjusted to any of three angles.
Adjust the display to the angle that allows for easy operation.
➜Press an edge of the display to adjust it to the desired angle.
Upper positionMiddle position
Lower position
Downloaded From ManualsPrinter.com Manuals 
						

							22.7 Power Supply
2-22 Di1611/Di2011
Precautions
Chapter 2
2.7 Power Supply
To turn on the machine
Set the Power Switch to “I”.
The indicator on the [Start] key lights up in 
orange, and the message “∗PLEASE 
WAIT!∗” appears in the display.
✎
Note
If the [Start] key is pressed while the 
indicator is lit in orange, the copy job is 
queued. When the indicator on the 
[Start] key lights up in green, the 
loaded document is scanned and 
copies are produced.
To turn off the machine
1Check that all jobs are finished.
❍If printed pages remain in the Copy Tray, remove them.
2Set the Power Switch to “2”.
Default Settings
The settings that are automatically selected when the machine is turned off or the 
[Panel Reset] key is pressed are called the “default settings”. These settings serve 
as a reference for all functions.
Copy mode
Number of copies: 1
Copy density: AUTO
Zoom ratio: Full size (× 1.00)
Paper source: AUTO (with the Document Feeder installed)
Finishing function: Non-sort
✎
Tip
The default settings can be customized using the functions in the Utility mode 
(“7 Utility Mode – Copy Functions”).
Downloaded From ManualsPrinter.com Manuals 
						

							2.7 Power Supply2
Di1611/Di2011 2-23
Precautions
Chapter 2
Auto Panel Reset
With the auto panel reset operation, the Copy mode screen appears after copying 
or after a specified length of time has passed after the last operation is finished. 
(Manufacturer’s default setting: 1 minute)
✎
Tip
The length of time until the auto panel reset operation is performed can be set 
to 30 seconds or a setting between 1 and 5 minutes.
In addition, the Auto Panel Reset function can be disabled.
For details, refer to “To set the “AUTO PANEL RESET” function” on page 7-7.
Energy Save Mode
With the Energy Save mode, the machine automatically enters a standby mode 
(Energy Save mode), instead of turning off.
When the machine is in Energy Save mode, the indicator on the [Start] key remains 
lit in green, but the display goes off.
✎
Note
If the Auto Shut Off function is activated during Energy Save mode, the machine 
turns off.
Conditions for entering Energy Save mode
The [Energy Save] key is pressed.
The specified length of time after the last operation has elapsed. 
(Manufacturer’s default setting: 15 minutes)
✎
Tip
The length of time until the machine enters Energy Save mode can be set 
between 1 and 240 minutes. (Refer to “To set the “ENERGY SAVE MODE” 
(preheat mode) function” on page 7-8.)
Auto Shut Off
With the Auto Shut Off function, the machine automatically turns off if no operation 
is performed for a specified length of time, in order to conserve energy. 
(Manufacturer’s default setting: 30 minutes)
Downloaded From ManualsPrinter.com Manuals 
						

							22.7 Power Supply
2-24 Di1611/Di2011
Precautions
Chapter 2
Queued Copy Jobs
Copy jobs can be queued by loading the document and pressing the [Start] key 
while “∗PLEASE WAIT!∗” appears in the display.
When the indicator on the [Start] key lights up in green, scanning of the loaded 
document begins, and copies are produced.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic Operations
Chapter 3
3
3Basic
Operations
Downloaded From ManualsPrinter.com Manuals