Konica Minolta Di2011 User Manual

							55.5 Selecting the Paper Source
5-22 Di1611/Di2011
Before Making Copies
Chapter 5
5.5 Selecting the Paper Source
The paper used for making copies can be selected in two ways.
Auto Paper:
If the Auto Paper function is selected, the paper tray containing the most 
suitable size of paper is selected based on the size of the document and the 
specified zoom ratio.
Manual paper selection:
The paper that you wish to use for copying can be selected.
To make copies using the Auto Paper function
1Load the document into the Automatic Document Feeder.
❍Refer to “Loading the Document” on page 3-9.
2Press the [Auto Paper/Auto Size] key 
until the Auto Paper function is 
selected.
❍Check that “AUTO” appears in the 
bottom line of the screen.
3If necessary, specify any other copy settings.
❍Zoom (p. 5-30)
❍Copy density (p. 5-36)
❍Advanced Copy Operations (p. 6-1)
4Using the 10-Key Pad, enter the desired number of copies, and then press the 
[Start] key.
✎
Note
If “NO SUITABLE PAPER” appears in the display immediately after the [Start] 
key is pressed, no tray is loaded with paper of the most suitable size. Either load 
paper with the appropriate size, or press the [Paper] key and select the desired 
paper size, and then press the [Start] key again.
Downloaded From ManualsPrinter.com Manuals 
						

							5.5 Selecting the Paper Source5
Di1611/Di2011 5-23
Before Making Copies
Chapter 5
To copy with a manually selected paper size
1Load the document to be copied.
❍Refer to “Loading the Document” on page 3-9.
2Press the [Paper] key, and then select 
the desired paper size.
❍Check that the correct paper size 
appears in the bottom line of the 
screen.
3If necessary, specify any other copy settings.
❍Zoom (p. 5-30)
❍Copy density (p. 5-36)
❍Advanced Copy Operations (p. 6-1)
4Using the 10-Key Pad, enter the desired number of copies, and then press the 
[Start] key.
Downloaded From ManualsPrinter.com Manuals 
						

							55.5 Selecting the Paper Source
5-24 Di1611/Di2011
Before Making Copies
Chapter 5
To load special paper into the 1st Tray
If special paper, such as OHP transparencies, postcards or cards are loaded into 
the 1st Tray, first set the “TRAY1 PAPER” function in the “PAPER SOURCE 
SETUP” menu of the Utility mode (“To specify the size of paper loaded into the 1st 
Tray (“TRAY1 PAPER” function)” on page 7-19).
Depending on the paper type set for the “TRAY1 PAPER” function, the screen 
changes as shown below.
Cards OHP transparencies
Postcards or envelopes
Downloaded From ManualsPrinter.com Manuals 
						

							5.5 Selecting the Paper Source5
Di1611/Di2011 5-25
Before Making Copies
Chapter 5
Automatically Selecting the Paper Source
With the auto tray switching feature, printing can continue with paper from a 
different paper drawer if the currently selected drawer runs out of paper during 
printing.
✎
Note
If paper is loaded into the Manual Bypass, the auto tray switching feature does 
not function.
The auto tray switching feature functions if the currently selected paper drawer and 
another paper drawer (except the Manual Bypass) meet the following conditions.
The paper is the same size.
The paper is the same type.
The paper is positioned in the same orientation.
The “PAPER TYPE” function is set to “PLAIN”, “RECYCLE” or “1-SIDE” for both 
paper trays.
✎
Tip
If the optional Multiple Bypass and the 5th paper drawer are installed, a 
maximum of 1350 copies (on A4 C paper) can be made continuously.
When making a large number of copies continuously, load all paper drawers 
(except the Manual Bypass) with paper meeting the conditions listed above.
If there is no paper in any paper drawer, a message appears indicating that 
paper must be replenished. Copying may not continue if paper is loaded into 
other paper drawers than the one specified in the message.
Downloaded From ManualsPrinter.com Manuals 
						

							55.5 Selecting the Paper Source
5-26 Di1611/Di2011
Before Making Copies
Chapter 5
Order for Automatically Switching Paper Drawers
When a different paper drawer is automatically selected, the next paper drawer in 
the following list is chosen.
1st paper drawer → 2nd paper drawer → 3rd paper drawer → 4th paper drawer 
→ 5th paper drawer → Multiple Bypass
✎
Note
If special media, such as OHP transparencies or label sheets, are loaded into 
the 1st paper drawer or the Multiple Bypass, the auto tray switching feature may 
cause the paper to be fed incorrectly.
In this case, we recommend that the settings be changed as follows. For the 1st 
paper drawer, change the paper type using the “TRAY1 PAPER” function on the 
“PAPER SOURCE SETUP” menu of the Utility mode (p. 7-19). For the Multiple 
Bypass, specify the paper type after loading the paper (p. 5-16).
Downloaded From ManualsPrinter.com Manuals 
						

							5.6 Original Documents5
Di1611/Di2011 5-27
Before Making Copies
Chapter 5
5.6 Original Documents
Using the Document Feeder
The document feeder automatically feeds in, scans, then feeds out each page of a 
multi-page document, one page at a time. The correct type of document must be 
loaded in order for the document feeder to function properly.
Using an incorrect type of document may cause a paper misfeed or damage to the 
document or machine.
✎
Note
In order to copy double-sided documents, the Duplexing Document Feeder 
AFR-19 (for Di2011) must be installed.
Document Types
Single-sided documents Double-sided documents Documents of mixed sizes
Downloaded From ManualsPrinter.com Manuals 
						

							55.6 Original Documents
5-28 Di1611/Di2011
Before Making Copies
Chapter 5
Documents of Uniform Sizes
Mixed Width Document Sizes (AFR-19)
2: Copying possible
—: Copying not possible
Document feed 
methodDocument typeDocument size
Document Feeder Sheet documents
Single-sided documents
AF-12
Capacity: 50 g/m
2 to 110 g/m2
AFR-19
Capacity: 35 g/m2 to 128 g/m2
Double-sided documents
AFR-19
Capacity: 50 g/m
2 to 128 g/m2
Documents of mixed sizes
AF-12
Capacity: 60 g/m
2 to 90 g/m2
AFR-19
Capacity: 50 g/m2 to 128 g/m2
AF-12
A3 L, B4 L, A4 L/C, B5 L/C, 
A5 L/C
AFR-19
A3 L, B4 L, A4 L/C, B5 L/C, 
A5 L/C, B6 L
Document width: 90 mm to 
297 mm
Document length: 210 mm to 
432 mm
With mixed documents widths
AF-12
A3 L and A4 C
B4 L and B5 C
A4 L and A5 C
AFR-19
Refer to the table below.
Original Glass Sheet documents, books, and 
large objects
Maximum weight: 3 kgA3 L, B4 L, A4 L/C, B5 L/C, 
A5 L/C
Document width: Up to 297 mm
Document length: Up to 432 mm
Maximum Document 
Width297 mm257 mm210 mm182 
mm148 
mm
Mixed Width 
Document DetectionA3 LA4 CB4 LB5 CA4 LA5 CB5 LA5 L
297 mm A3 L22——————
A4 C22——————
257 mm B4 L2222————
B5 C2222————
210 mm A4 L222222——
A5 C222222——
182 mm B5 L——22222—
148 mm A5 L——————22
Downloaded From ManualsPrinter.com Manuals 
						

							5.6 Original Documents5
Di1611/Di2011 5-29
Before Making Copies
Chapter 5
Precautions Concerning the Documents
The following types of documents should not be loaded into the Duplexing 
Document Feeder, otherwise paper misfeeds or damage to the document may 
occur. Instead, these types of documents should be positioned on the original 
glass.
Documents on special paper
Folded documents (folded in half or fanned)
Highly translucent or transparent documents, such as diazo photosensitive 
paper
Documents with binder holes
Documents with many binder holes, such as loose-leaf paper
Coated documents, such as heat-sensitive or carbon-backed paper
Inkjet printer paper
Documents that have just been printed with this machine
Documents on paper that cannot be fed
Curled documents
Wrinkled or torn documents
Overhead transparencies
If non-standard-sized paper is determined to be close to a standard size, copying 
with the “Auto Paper” or “Auto Size ”functions is possible.
✎
Note
If a document of a non-standard size is positioned on the Original Glass, the 
Auto Paper and the Auto Size functions are not available.
After loading a document of a non-standard size, press the [Paper] key to select 
a paper size or press the [Zoom] key to select a zoom ratio.
Downloaded From ManualsPrinter.com Manuals 
						

							55.7 Specifying a Zoom Setting
5-30 Di1611/Di2011
Before Making Copies
Chapter 5
5.7 Specifying a Zoom Setting
By specifying a zoom ratio, the copy can be enlarged or reduced.
Zoom Settings
“Zoom” settingDescription
Full size Copies are made at the same size as the document (
× 1.00).
“AUTO”  zoom  ratio The most appropriate zoom ratio is automatically selected based on the 
size of the document loaded and the specified paper size.
Preset zoom ratios The following common zoom ratios for copying from various standard 
document sizes to standard paper sizes are available.
× 0.50 × 0.70 (A3 A4 and B4 B5)× 0.81 (B4 A4 and B5 A5)× 1.15 (B4 A3 and B5 A4)× 1.41 (A4 A3 and B5 B4)× 2.00
Zoom ratios selected using 
the and Zoom keysUsing the and keys, the zoom ratio can be adjusted (increased or 
reduced) in 0.01 increments.
A zoom ratio between 
× 0.50 and × 2.00 can be set.
“X/Y Zoom” function Copies can be made using different scaling proportions for the vertical 
and horizontal directions.
Using the and keys, the zoom ratio can be adjusted (increased or 
reduced) in 0.01 increments.
The vertical and horizontal zoom ratios can be set between 
× 0.50 and × 1.00.
Downloaded From ManualsPrinter.com Manuals 
						

							5.7 Specifying a Zoom Setting5
Di1611/Di2011 5-31
Before Making Copies
Chapter 5
To make copies using the “AUTO” zoom setting
1Load the document to be copied.
❍Refer to “Loading the Document” on page 3-9.
2Press the [Auto Paper/Auto Size] key 
until the Auto Size function is 
selected.
❍Check that “AUTO” appears in the 
top line of the screen.
3Press the [Paper] key, and then select 
the desired paper size.
4If necessary, specify any other copy settings.
❍Copy density (p. 5-36)
❍Advanced Copy Operations (p. 6-1)
5Using the 10-Key Pad, enter the desired number of copies, and then press the 
[Start] key.
Downloaded From ManualsPrinter.com Manuals