Konica Minolta Di2011 User Manual

							77.6 Specifying Copy Settings
7-38 Di1611/Di2011
Utility Mode – Copy Functions
Chapter 7
7.6 Specifying Copy Settings
“COPY SETTING 1” & “COPY SETTING 2” menus
The settings that are automatically selected when the machine is turned off or the 
[Panel Reset] key is pressed are called the “default settings”. From the “COPY 
SETTING 1” menu, the default settings for various functions can be specified.
“COPY SETTING 1” menu:
No.COPY SETTING 1Description
1 PAPER PRIORITY This function can be used to specify the tray that should be 
given priority when the “AUTO” Zoom setting is selected.
The manufacturer’s default setting is “1ST”.
2 DENSITY PRIORITY This function can be used to set the density to “TEXT”, 
“PHOTO” or “TEXT/P” when the machine is turned off or the 
[Panel Reset] key is pressed.
The manufacturer’s default setting is “TEXT/P”.
3 DENSITY LEVEL(A) This function can be used to set the density level of the “AUTO” 
Density setting to one of the three settings between “LIGHT” 
and “DARK”.
The manufacturer’s default setting is the middle level 
().
4 DENSITY LEVEL(M) This function can be used to set the density level of the manual 
density setting to one of the nine settings between “LIGHT” and 
“DARK”.
The manufacturer’s default setting is the middle level 
().
5 BINDING  POS. This function can be used to set whether the first page of a book 
to be scanned is on the left (left-bound) or on the right (right-
bound).
The manufacturer’s default setting is “LEFT”.
6 MARGIN SETTING This function can be used to specify the width of the binding 
area (margin) between 0 mm and 20 mm (in units of 1 mm) 
when copying documents to be bound.
The manufacturer’s default setting is 10 mm.
7 ERASE SETTING This function can be used to specify between 5 mm and 20 mm 
(in units of 1 mm) the width that is erased when making copies 
with the “Erase” function set to “LEFT”, “UPPER” or “FRAME”.
The manufacturer’s default setting for the “LEFT”, “UPPER” 
and “FRAME” Erase settings is 10 mm.
8 SMALL ORIGINAL This function is used to specify whether or not copying is 
possible after loading a small document whose size cannot be 
automatically detected.
The manufacturer’s default setting is “ENABLE”.
Downloaded From ManualsPrinter.com Manuals 
						

							7.6 Specifying Copy Settings7
Di1611/Di2011 7-39
Utility Mode – Copy Functions
Chapter 7
“COPY SETTING 2” menu:
No.COPY SETTING 2Description
1 MIXED  ORIGINAL This function can be used to set whether or not the “Mixed Orig.” 
function is selected when the machine starts up or after the 
Control Panel is reset.
This function can be set if an optional Document Feeder is 
installed.
The manufacturer’s default setting is “OFF”.
2 COPY  PRIORITY This function can be used to set whether the automatic paper or 
automatic zoom ratio setting is selected when the machine 
starts up or after the Control Panel is reset.
The manufacturer’s default setting is “AP” (auto paper 
selection).
3 OUTPUT PRIORITY This function can be used to specify if the selected Finishing 
mode is “NON”, “SORT” or “GROUP” when the machine is 
turned off or the [Panel Reset] key is pressed.
This function can be set if an optional Document Feeder is 
installed.
The manufacturer’s default setting is “NON”.
4 4IN1 COPY ORDER This function can be used to select from the following for the 
page order when the 4in1 Copy mode is selected.
“PATTERN1”“PATTERN2”
This function can be set if an optional Document Feeder is 
installed.
The manufacturer’s default setting is “PATTERN1”.
5 CRISSCROSS MODE This function can be used to set whether or not copies are fed 
out in a crisscross pattern when the crisscross output conditions 
are met.
This function can be set if an optional Document Feeder and 
Job Shifter are installed.
The manufacturer’s default setting is “ON”.
6 DUPLEX COPY This function is used to select whether or not double-sided 
printing is used.
The optional Duplex Unit must be installed. (Option only for the 
Di2011)
The manufacturer’s default setting is “OFF”.
12
3413
24
Downloaded From ManualsPrinter.com Manuals 
						

							77.6 Specifying Copy Settings
7-40 Di1611/Di2011
Utility Mode – Copy Functions
Chapter 7
To select the “COPY SETTING 1” menu
1Press the [Utility] key.
“MACHINE SETTING?” appears.
2Press the key 4 times to select 
“COPY SETTING 1?”.
3From the 10-Key Pad, press the key for the “COPY SETTING 1” function that 
you wish to set.
❍The “COPY SETTING 1” functions are as follows:
1 PAPER PRIORITY
2 DENSITY PRIORITY
3 DENSITY LEVEL(A)
4 DENSITY LEVEL(M)
5 BINDING POS.
6 MARGIN SETTING
7 ERASE SETTING
8 SMALL ORIGINAL
✎
Tip
If, at any time, you wish to quit setting a “COPY SETTING 1” function, press the 
[No] key. When the message “STOP SETTING?” appears, press the [Yes] key 
to quit.
Downloaded From ManualsPrinter.com Manuals 
						

							7.6 Specifying Copy Settings7
Di1611/Di2011 7-41
Utility Mode – Copy Functions
Chapter 7
To set the “PAPER PRIORITY” function
1Select the “COPY SETTING 1” menu.
❍Refer to “To select the “COPY 
SETTING 1” menu” on page 7-40.
2Press the [1] key from the 10-Key Pad 
to select “PAPER PRIORITY”.
3Using the and keys, select a 
paper size or paper tray, and then 
press the [Yes] key.
❍Select from the following paper 
trays.
1st Tray, 2nd Tray, 3rd Tray*, 4th 
Tray*, 5th Tray*, Multiple Bypass
*Only with Di2011
❍If the 5th Tray and Multiple Bypass 
are installed, the screen shown at 
the right appears.
The “COPY SETTING 1” menu 
appears again.
✎
Tip
If there are multiple paper drawers loaded with paper of the same size and 
type as that loaded into the paper drawer given priority with the “PAPER 
PRIORITY” function, and if the paper in all of these paper drawers are used, 
a message may appear indicating that paper be loaded into a paper drawer 
that was not given priority.
In this case, load paper according to the message that appears.
Downloaded From ManualsPrinter.com Manuals 
						

							77.6 Specifying Copy Settings
7-42 Di1611/Di2011
Utility Mode – Copy Functions
Chapter 7
To set the “DENSITY PRIORITY” function
1Select the “COPY SETTING 1” menu.
❍Refer to “To select the “COPY 
SETTING 1” menu” on page 7-40.
2Press the [2] key from the 10-Key Pad 
to select “DENSITY PRIORITY”.
3Using the and keys, select 
“TEXT”, “PHOTO” or “TEXT/P”, and 
then press the [Yes] key.
❍If “TEXT” or “TEXT/P” is selected, 
a screen appears, allowing you to 
select either “AUTO” or 
“MANUAL”.
Using the and keys, 
select either “AUTO” or 
“MANUAL”, and then press the [Yes] key.
The “COPY SETTING 1” menu appears again.
Downloaded From ManualsPrinter.com Manuals 
						

							7.6 Specifying Copy Settings7
Di1611/Di2011 7-43
Utility Mode – Copy Functions
Chapter 7
To set the “AUTO” density level (“DENSITY LEVEL(A)” function)
1Select the “COPY SETTING 1” menu.
❍Refer to “To select the “COPY 
SETTING 1” menu” on page 7-40.
2Press the [3] key from the 10-Key Pad 
to select “DENSITY LEVEL(A)”.
3Using the and keys, select 
one of the three settings between 
“LIGHT” and “DARK”, and then press 
the [Yes] key.
The “COPY SETTING 1” menu 
appears again.
Downloaded From ManualsPrinter.com Manuals 
						

							77.6 Specifying Copy Settings
7-44 Di1611/Di2011
Utility Mode – Copy Functions
Chapter 7
To set the manual density level (“DENSITY LEVEL(M)” function)
1Select the “COPY SETTING 1” menu.
❍Refer to “To select the “COPY 
SETTING 1” menu” on page 7-40.
2Press the [4] key from the 10-Key Pad 
to select “DENSITY LEVEL(M)”.
3Using the and keys, select 
one of the nine settings between 
“LIGHT” and “DARK”, and then press 
the [Yes] key.
The “COPY SETTING 1” menu 
appears again.
Downloaded From ManualsPrinter.com Manuals 
						

							7.6 Specifying Copy Settings7
Di1611/Di2011 7-45
Utility Mode – Copy Functions
Chapter 7
To set the “BINDING POS.” function
1Select the “COPY SETTING 1” menu.
❍Refer to “To select the “COPY 
SETTING 1” menu” on page 7-40.
2Press the [5] key from the 10-Key Pad 
to select “BINDING POS.”.
3Using the and keys, select 
either “LEFT” or “RIGHT”, and then 
press the [Yes] key.
The “COPY SETTING 1” menu 
appears again.
Downloaded From ManualsPrinter.com Manuals 
						

							77.6 Specifying Copy Settings
7-46 Di1611/Di2011
Utility Mode – Copy Functions
Chapter 7
To specify the binding width (“MARGIN SETTING” function)
1Select the “COPY SETTING 1” menu.
❍Refer to “To select the “COPY 
SETTING 1” menu” on page 7-40.
2Press the [6] key from the 10-Key Pad 
to select “MARGIN SETTING”.
3Using the 10-Key Pad, enter the 
binding width (margin), and then press 
the [Yes] key.
❍The binding width can be set 
between 0 mm and 20 mm.
❍If you wish to correct the setting, 
press the [No] key, and then enter the new number.
The “COPY SETTING 1” menu appears again.
Downloaded From ManualsPrinter.com Manuals 
						

							7.6 Specifying Copy Settings7
Di1611/Di2011 7-47
Utility Mode – Copy Functions
Chapter 7
To specify the erased width (“ERASE SETTING” function)
1Select the “COPY SETTING 1” menu.
❍Refer to “To select the “COPY 
SETTING 1” menu” on page 7-40.
2Press the [7] key from the 10-Key Pad 
to select “ERASE SETTING”.
3Using the and keys, select 
“LEFT”, “UPPER” or “FRAME”, and 
then press the [Yes] key.
4Using the 10-Key Pad, enter the width 
of the area to be erased, and then 
press the [Yes] key.
❍The width of the area to be erased 
can be set between 5 mm and 20 
mm.
❍If you wish to correct the setting, press the [No] key, and then enter the new 
number.
The “COPY SETTING 1” menu appears again.
Downloaded From ManualsPrinter.com Manuals