Konica Minolta Di2011 User Manual

							77.3 Setting Up the Paper Sources (“PAPER SOURCE SETUP” Menu)
7-18 Di1611/Di2011
Utility Mode – Copy Functions
Chapter 7
To specify the automatic paper size detection units (“INCH/METRIC” 
function)
1Select the “PAPER SOURCE SETUP” 
menu.
❍Refer to “To select the “PAPER 
SOURCE SETUP” menu” on 
page 7-17.
2Press the [1] key from the 10-Key Pad 
to select “INCH/METRIC”.
3Using the and keys, select a 
paper tray, and then press the [Yes] 
key.
4Using the and keys, select 
either “METRIC” or “INCH”, and then 
press the [Yes] key.
The “PAPER SOURCE SETUP” 
menu appears again.
Downloaded From ManualsPrinter.com Manuals 
						

							7.3 Setting Up the Paper Sources (“PAPER SOURCE SETUP” Menu)7
Di1611/Di2011 7-19
Utility Mode – Copy Functions
Chapter 7
To specify the size of paper loaded into the 1st Tray (“TRAY1 PAPER” 
function)
1Select the “PAPER SOURCE SETUP” 
menu.
❍Refer to “To select the “PAPER 
SOURCE SETUP” menu” on 
page 7-17.
2Press the [2] key from the 10-Key Pad 
to select “TRAY1 PAPER”.
3Using the and keys, select 
“PLAIN”, “OHP”, “CARD” or 
“ENVELOPE”, and then press the 
[Yes] key.
4Using the and keys, select 
either “AUTO” or “SIZE INPUT”, and 
then press the [Yes] key.
❍If “AUTO” was selected, the 
“PAPER SOURCE SETUP” menu 
appears again.
❍If “SIZE INPUT” was selected, a screen appears, allowing you to specify the 
paper size.
5Using the 10-Key Pad, enter the paper 
length (mm), and then press the [Yes] 
key.
❍The paper length can be set 
between 140 mm and 432 mm.
❍If you wish to correct the setting, 
press the [No] key, and then enter the new number.
Downloaded From ManualsPrinter.com Manuals 
						

							77.3 Setting Up the Paper Sources (“PAPER SOURCE SETUP” Menu)
7-20 Di1611/Di2011
Utility Mode – Copy Functions
Chapter 7
✎
Note
The paper length is set between 
421 mm and 432 mm, the 
maximum width that can be set is 
279 mm.
The paper width is set between 
280 mm and 297 mm, the 
maximum length that can be set is 
420 mm.
?Have the necessary precautions been observed when entering the paper 
size?
➜Refer to the diagram at the right 
and be sure to specify the paper 
width and length measurements 
correctly.
6Using the 10-Key Pad, enter the paper 
width (mm).
❍The paper width can be set 
between 90 mm and 297 mm.
❍If you wish to correct the setting, 
press the [No] key, and then enter 
the new number.
421 mm to 432 mm
Less than 297 mm
(Width)
(Length)
Less than 420 mm
280 mm to 297mm
(Width)
(Length)
x
y
Downloaded From ManualsPrinter.com Manuals 
						

							7.3 Setting Up the Paper Sources (“PAPER SOURCE SETUP” Menu)7
Di1611/Di2011 7-21
Utility Mode – Copy Functions
Chapter 7
7Press the [Yes] key.
The “PAPER SOURCE SETUP” menu appears again.
Downloaded From ManualsPrinter.com Manuals 
						

							77.3 Setting Up the Paper Sources (“PAPER SOURCE SETUP” Menu)
7-22 Di1611/Di2011
Utility Mode – Copy Functions
Chapter 7
To set the “PAPER TYPE” function
1Select the “PAPER SOURCE SETUP” 
menu.
❍Refer to “To select the “PAPER 
SOURCE SETUP” menu” on 
page 7-17.
2Press the [3] key from the 10-Key Pad 
to select “PAPER TYPE”.
3Using the and keys, select a 
paper tray, and then press the [Yes] 
key.
4Using the and keys, select 
either “PLAIN”, “RECYCLE” or 
“SPECIAL”, “1-SIDE” and then press 
the [Yes] key.
The “PAPER SOURCE SETUP” 
menu appears again.
✎
Note
“1-SIDE” is displayed only when the machine is equipped with the Duplex Unit 
(option for the Di2011 only).
Downloaded From ManualsPrinter.com Manuals 
						

							7.4 Specifying User-Managed Service Tasks (“USER MANAGEMENT” Menu)7
Di1611/Di2011 7-23
Utility Mode – Copy Functions
Chapter 7
7.4 Specifying User-Managed Service Tasks (“USER 
MANAGEMENT” Menu)
From the “USER MANAGEMENT” menu, certain service operations can be 
performed in order to maintain the machine’s efficiency.
“USER MANAGEMENT” menu:
No.USER MANAGEMENTDescription
1 DRUM  DEHUMIDIFY When the room temperature changes drastically (such as when 
a heater is used in the winter) or when the machine is used in 
an extremely humid location, condensation may form on the 
surface of the PC drum inside the machine, resulting in 
decreased print quality. If this occurs, use this function to dry the 
drum and eliminate the condensation.
The drum dehumidifying operation lasts three minutes.
2 TONER REPLENISHER After many documents containing large printed areas (such as 
photos) or many negative/positive-inverted copies are printed, 
the print density may temporarily become too light if toner is not 
automatically replenished. If this occurs, use this function to 
force replenishing of the toner and immediately return the 
density to its normal level.
Downloaded From ManualsPrinter.com Manuals 
						

							77.4 Specifying User-Managed Service Tasks (“USER MANAGEMENT” Menu)
7-24 Di1611/Di2011
Utility Mode – Copy Functions
Chapter 7
To perform the “DRUM DEHUMIDIFY” function
1Press the [Utility] key.
“MACHINE SETTING?” appears.
2Press the key twice to select 
“USER MANAGEMENT?”, and then 
press the [Yes] key.
3Using the and keys, select 
“DRUM DEHUMIDIFY?”, and then 
press the [Yes] key.
Drum drying begins, and the main 
screen appears.
Downloaded From ManualsPrinter.com Manuals 
						

							7.4 Specifying User-Managed Service Tasks (“USER MANAGEMENT” Menu)7
Di1611/Di2011 7-25
Utility Mode – Copy Functions
Chapter 7
To perform the “TONER REPLENISHER” function
1Press the [Utility] key.
“MACHINE SETTING?” appears.
2Press the key twice to select 
“USER MANAGEMENT?”, and then 
press the [Yes] key.
3Using the and keys, select 
“TONER REPLENISHER?”, and then 
press the [Yes] key.
Toner replenishing begins, and the 
main screen appears.
✎
Note
While the toner is being replenished, do not turn off the machine or open the 
Front Cover.
If the density of the toner is suitable, do not perform the toner replenishing 
operation.
Downloaded From ManualsPrinter.com Manuals 
						

							77.5 Specifying Administrative Settings (“ADMIN. MANAGEMENT” Menu)
7-26 Di1611/Di2011
Utility Mode – Copy Functions
Chapter 7
7.5 Specifying Administrative Settings (“ADMIN. 
MANAGEMENT” Menu)
From the “ADMIN. MANAGEMENT” menu, various functions for controlling the use 
of the machine can be set. In order to set an “ADMIN. MANAGEMENT” function, 
the administrator access number must be entered.
“ADMIN. MANAGEMENT” menu:
✎
Note
The registering and setup of the administrator access number should be 
performed by the service representative. For details, contact the service 
representative.
The administrator of this machine should be sure not to lose the administrator 
access number.
No.ADMIN. MANAGEMENTDescription
1 AUTO SHUT OFF This function can be used to set whether or not the auto power-
off function is performed.
The manufacturer’s default setting is “ENABLE”.
2 COPY TRACK A maximum of 20 accounts can be specified in order to control 
the use of the machine.
Turn on/off user management.
Register account access numbers.
Change/delete account access numbers.
Display/clear the total count for a specific account.
Clear the total counts for all accounts.
Downloaded From ManualsPrinter.com Manuals 
						

							7.5 Specifying Administrative Settings (“ADMIN. MANAGEMENT” Menu)7
Di1611/Di2011 7-27
Utility Mode – Copy Functions
Chapter 7
To select the “ADMIN. MANAGEMENT” menu
1Press the [Utility] key.
“MACHINE SETTING?” appears.
2Press the key 3 times to select 
“ADMIN. MANAGEMENT?”.
3From the 10-Key Pad, press the key ([1] through [2]) for the “ADMIN. 
MANAGEMENT” function that you wish to set.
❍The “ADMIN. MANAGEMENT” functions are as follows:
1 AUTO SHUT OFF
2 COPY TRACK
4Using the 10-Key Pad, enter the 6-
digit administrator access number, 
and then press the [Yes] key.
✎
Tip
If, at any time, you wish to quit setting an “ADMIN. MANAGEMENT” function, 
press the [No] key. When the message “STOP SETTING?” appears, press the 
[Yes] key to quit.
Downloaded From ManualsPrinter.com Manuals
Utility Mode – Copy Functions
Chapter 7
7Using the and keys, select 
“OFF”, and then press the [Yes] key.
The “MACHINE SETTING” menu 
appears again.
✎
Note
If the “AUTO SHUT OFF” function on the “ADMIN. MANAGEMENT” menu is set 
to “DISABLE”, it will no longer be possible to make copies or print from a 
computer after the Auto Shut Off function is performed and the machine is 
turned off.
To make copies or print from a computer, turn on the machine.
Downloaded From ManualsPrinter.com Manuals