Konica Minolta Di2011 User Manual

							99.1 When Incorrect Copies Are Produced
9-2 Di1611/Di2011
Troubleshooting
Chapter 9
9.1 When Incorrect Copies Are Produced
SymptomPossible CauseRemedy
The copy is too light. The copy density is set too 
light.Use the Auto/Photo 
key to select a darker 
copy density (p. 5-36).
The copy paper is damp. Replace the paper. (p. 3-5)
The copy is too dark. The copy density is set too 
dark.Use the Auto/Photo 
key to select a lighter 
copy density (p. 5-36).
The document was not 
pressed close enough 
against the Original Glass.Position the document so 
that it is pressed closely 
against the Original Glass. 
(p. 3-11)
The copy is blurry. The copy paper is damp. Replace the paper. (p. 3-5)
The document was not 
pressed close enough 
against the Original Glass.Position the document so 
that it is pressed closely 
against the Original Glass. 
(p. 3-11)
There are streaks through the 
copy.
There are specks throughout 
the entire copy.The Original Glass is dirty. Wipe the glass with a soft 
dry cloth. (p. 10-7)
The document pad is dirty. Clean the document pad 
with a soft cloth dampened 
with a mild detergent. 
(p. 10-7)
The original is highly 
translucent, such as diazo 
photosensitive paper or 
OHP transparencies.Place a blank sheet of 
paper over the document. 
(p. 3-13)
A double-sided document is 
being copied.If a thin double-sided 
document is being copied, 
the information on the back 
side may be reproduced in 
the copy. Use the Auto/
Photo key to select a 
lighter density for the 
background. (p. 5-36)
The Imaging Unit has 
reached the end of its 
service life.Contact your service 
representative.
Downloaded From ManualsPrinter.com Manuals 
						

							9.1 When Incorrect Copies Are Produced9
Di1611/Di2011 9-3
Troubleshooting
Chapter 9
The edge of the copy is dirty. The document pad is dirty. Clean the document pad 
with a soft cloth dampened 
with a mild detergent. 
(p. 10-7)
The selected paper size is 
larger than the document 
(with a Zoom setting of 
×1.00).Select a copy paper size 
that is the same as the size 
of the document. (p. 5-22)
Otherwise, select the Auto 
Size function to enlarge the 
copy to the selected paper 
size. (p. 5-30)
The orientation of the 
document is different from 
the orientation of the copy 
(with a Zoom setting of 
×1.00).Select a copy paper size 
that is the same as the size 
of the document. 
Otherwise, select a copy 
orientation that is the same 
as the orientation of the 
document.
The copy was reduced to a 
size smaller than the paper 
(with a reduced zoom ratio).Select a zoom ratio that 
adjusts the copy size to the 
size of the selected paper. 
(p. 5-30)
Otherwise, select the Auto 
Size function to reduce the 
copy to the selected paper 
size. (p. 5-22)
The image is not aligned 
properly on the paper.The document is not 
positioned correctly.Correctly position the 
document against the 
Document Scales. (p. 3-11)
If the Document Feeder is 
installed, correctly adjust 
the Document Guide Plates 
for the size of the 
document. (p. 3-9)
The document is not 
positioned correctly in the 
Document Feeder.Lift open the Document 
Feeder, and correctly 
position the document 
against the Document 
Scales. (p. 3-11)
The Document Guide 
Plates are not slid up 
against the edges of the 
document.Slide the Document Guide 
Plates against the edges of 
the document.
Curled paper was loaded 
into the paper tray.Flatten the paper before 
loading it.
SymptomPossible CauseRemedy
Downloaded From ManualsPrinter.com Manuals 
						

							99.2 When Copying Is Not Performed Correctly
9-4 Di1611/Di2011
Troubleshooting
Chapter 9
9.2 When Copying Is Not Performed Correctly
SymptomPossible CauseRemedy
Nothing appears on the 
display.Only the [Start] key 
indicator is lit up in green.The machine is in Energy 
Saver mode (preheat 
mode).
Press any key to cancel 
Energy Save mode. 
(p. 2-23)
The “AUTO SHUT OFF” 
function was activated.Set the Power Switch to “O” 
(p. 2-22).
The [Start] key indicator is not 
lit up in green.A user (section) access 
number has not been 
entered.Enter the user (section) 
access number according 
to the instructions in Access 
Numbers (p. 6-23).
Even though the [Start] key is 
pressed, no copies are made.If the “Error” indicator on the 
Control Panel is lit, an error 
has occurred.Follow the instructions in 
any messages that appear 
on the display.
If the machine was just 
turned on, it is still warming 
up.The machine takes about 
30 seconds to warm up 
after it is turned on.
The machine cannot be set to 
Copy mode.The machine is in Interrupt 
mode (the Interrupt 
indicator is lit).Press the [Interrupt] key to 
cancel Interrupt mode. 
(p. 5-38)
The machine cannot be turned 
on.The power supply cord has 
been unplugged from the 
electrical outlet.Plug the power supply cord 
into the electrical outlet.
The breaker for the 
electrical circuit has been 
tripped.Close the breaker for the 
electrical circuit.
Downloaded From ManualsPrinter.com Manuals 
						

							Appendix
Chapter 10
10
10Appendix
Downloaded From ManualsPrinter.com Manuals 
						

							1010.1 Specifications
10-2 Di1611/Di2011
Appendix
Chapter 10
10.1 Specifications
Main Unit Di1611/Di2011
SpecificationDi1611Di2011
Type Desktop/Console*
Platen Stationary
Photo conductor OPC
Copying system Electro photographic printing system
Developing system MTHG system
Fusing system Heat-roller-fixing system
Resolution 600 dpi 
× 600 dpi
Document Types: Sheets, books, and other three-dimensional objects
Size: Maximum A3 L, Ledger L (11 
× 17 L)
Weight: 3 kg
Paper types Plain paper (60 g/m
2 to 90 g/m2), recycled paper 
(60 g/m2 to 90 g/m2)
Special paper: Thick paper (91 g/m2 to 157 g/m2), OHP 
transparencies, postcards, envelopes and label sheets
* Special paper can only be fed through the 1st Tray and the Manual 
Bypass.
Paper sizes 1st Tray:
In metric:
A3 L, B4 L, A4 L/C, B5 L/C, A5 L/C, FLS (210 mm 
× 330 mm)
In inches:
Ledger L, 11 
× 14 L, Legal L, Letter L/C, 
Invoice L/C (5-1/2 × 8-1/2 L/C)
Manual Bypass:
Width: 90 mm to 297 mm, length: 140 mm to 432 mm
Paper capacity 1st Tray:
Plain or recycled paper: 250 sheets
Special paper (cards, OHP transparencies, postcards, label sheets): 
20 sheets
Envelopes: 10 envelopes
Manual Bypass:
Plain, recycled or special paper: 1 sheet
Warm-up time Less than 30 seconds (at room temperature (23°C))
First-page print time Less than 7 seconds (using the 1st Tray loaded with A4 C)
Copy speed 7 sheets/minute (A3 L)
13 sheets/minute (A4 L)
16 sheets/minute (A4 C)
18 sheets/minute (B5 C)12 sheets/minute (A3 L)
16 sheets/minute (A4 L)
20 sheets/minute (A4 C)
23 sheets/minute (B5 C)
Magnification ratios Full size: 
× 1.00
Enlargement ratios: × 1.15, × 1.41, and × 2.00
Reduction ratios: × 0.81, × 0.70, and × 0.50
Zoom ratios: × 0.50 to × 2.00 (in 0.01 increments)
Multiple copies 1 to 99 sheets
Density control Automatic, manual
Downloaded From ManualsPrinter.com Manuals 
						

							10.1 Specifications10
Di1611/Di2011 10-3
Appendix
Chapter 10
* Depend on number of Paper Feed Unit option.Image loss Leading edge: 4 mm, Trailing edge: 4 mm, Rear edge: 4 mm, Front 
edge: 4 mm
Power requirements AC 220 to 240 V, 4.5 A (Di1611), 5.5 A (Di2011), 50/60 Hz
Power consumption 230 V: 1050 W (Di1611), 1250 W (Di2011)
Size 599 mm (width) 
× 620 mm (depth) × 487 mm (height)
Weight 39 kg
Standard memory Copier: 32 MB (Can be increased to a maximum of 96 MB.)
SpecificationDi1611Di2011
Downloaded From ManualsPrinter.com Manuals 
						

							1010.1 Specifications
10-4 Di1611/Di2011
Appendix
Chapter 10
Duplexing Document Feeder AFR-19
Mixed Width Document Sizes (AFR-19)
2: Copying possible
—: Copying not possible
Specification
Document feed method Standard method: Single-sided documents and double-sided 
documents
Mixed document sizes: Single-sided documents and double-sided 
documents
Document type Standard method: Plain paper
Single-sided: 35 g/m
2 to 128 g/m2
Double-sided: 50 g/m2 to 128 g/m2
“Mixed Orig.” function: Plain paper (50 g/m2 to 128 g/m2)
Document size Standard method: A3 L, B4 L, A4 L/C, B5 L/C, A5 L/C, B6 L
Mixed document sizes: Refer to the table below.
Document loading capacity Maximum 80 sheets (80 g/m
2)
Power consumption Less than 48 W
Size 582 mm (width) 
× 558 mm (depth) × 145 mm (height)
Weight Less than 9.4 kg
Maximum Document 
Width297 mm257 mm210 mm182 
mm148 
mm
Mixed Width 
Document DetectionA3 LA4 CB4 LB5 CA4 LA5 CB5 LA5 L
297 mm A3 L22——————
A4 C22——————
257 mm B4 L2222————
B5 C2222————
210 mm A4 L222222——
A5 C222222——
182 mm B5 L——22222—
148 mm A5 L——————22
Downloaded From ManualsPrinter.com Manuals 
						

							10.1 Specifications10
Di1611/Di2011 10-5
Appendix
Chapter 10
Automatic Document Feeder AF-12
Paper Feed Unit PF-126
Shifting Unit OT-103
Specification
Document feed method Standard method: Single-sided documents
Mixed document sizes: Single-sided documents
Document type Standard method: Plain paper (50 g/m
2 to 110 g/m2)
“Mixed Orig.” function: Plain paper (60 g/m2 to 90 g/m2)
Document size Standard method: A3 L, B4 L, A4 L/C, B5 L/C, A5 L/C
Mixed document sizes: Combination of A3 L and A4 C, B4 L and 
B5 C, or A4 L and A5 C
Document loading capacity Maximum 50 sheets (80 g/m
2)
Power consumption Less than 36 W
Size 598 mm (width) 
× 483 mm (depth) × 102 mm (height)
Weight Less than 6.3 kg
Specification
Paper types Plain paper (60 g/m2 to 90 g/m2), recycled paper (60 g/m2 to 90 g/
m2)
Paper sizes In metric:
A3 L, B4 L, A4 L/C, B5 L/C, A5 C, FLS (210 mm 
× 330 mm)
In inches:
Ledger L, 11 
× 14 L, Legal L, Letter L/C, Invoice C (5-1/2 × 8-1/2 C)
Paper capacity 250 sheets
Power consumption Less than 9 W
Size 590 mm (width) 
× 558 mm (depth) × 108 mm (height)
Weight 5.5 kg
Specification
Shifting amount 28 mm
Paper capacity 250 sheets
Power consumption Less than 63 W
Downloaded From ManualsPrinter.com Manuals 
						

							1010.1 Specifications
10-6 Di1611/Di2011
Appendix
Chapter 10
Job Separator JS-204
Multiple Bypass MB-6
Specification
Paper types Plain paper (60 g/m2 to 90 g/m2), recycled paper (60 g/m2 to 90 g/
m2)
Special paper: Cards (91 g/m2 to 157 g/m2), OHP transparencies, 
postcards, envelopes, and label sheets
Paper capacity Upper Copy Tray:
Plain or recycled paper: 100 A4-size sheets, 50 sheets of other than 
A4 size (stacked up to 22 mm high)
Special paper: 10 sheets
Lower Copy Tray:
Plain or recycled paper: 150 A4-size sheets, 75 sheets of other than 
A4 size
Special paper: 20 sheets
Power consumption Less than 24 W
Specification
Paper types Plain paper (60 g/m2 to 90 g/m2), recycled paper (60 g/m2 to 90 g/
m2)
Special paper: Cards (91 g/m2 to 157 g/m2), OHP transparencies, 
postcards, envelopes, and label sheets
Paper sizes A3 L, B4 L, A4 L/C, B5 L/C, A5 L/C, FLS (210 mm 
× 330 mm)
(Width: 90 mm to 297 mm; Length: 140 mm to 432 mm)
Paper capacity Plain or recycled paper: 100 sheets
Special paper (cards, OHP transparencies, postcards, label sheets): 
20 sheets
Envelopes: 10 envelopes
Power consumption Less than 9 W
Size (Maximum) 439 mm (width) 
× 435 mm (depth) × 137 mm (height)
Weight 3.0 kg
Downloaded From ManualsPrinter.com Manuals 
						

							10.2 Care of the Machine10
Di1611/Di2011 10-7
Appendix
Chapter 10
10.2 Care of the Machine
Cleaning
Turn off the machine before cleaning it.
Housing
➜Clean the surface of the housing by 
wiping it with a soft cloth dampened 
with a mild household detergent.
Original Glass
➜Clean the Original Glass by wiping it 
with a soft, dry cloth.
Document Pad
➜Clean the surface of the document 
pad by wiping it with a soft cloth 
dampened with alcohol.
Downloaded From ManualsPrinter.com Manuals