Canon Imageprograf Ipf825 User Guide
Have a look at the manual Canon Imageprograf Ipf825 User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Important • Do not touch the Linear Scale (a), Carriage Shaft (b), or Ink Tube Stabilizer (c). Touching these parts may damage them. 2. With a sheet lengthwise and printing-side up, insert it between the Platen (a) and the Paper Retainer (b). Align the edges of the sheet as follows. 1. Align the sheet with the Paper Alignment Line (c) at right. 2. Align the inserted edge of the sheet with the leading edge of the Paper Alignment Line (d), as shown. Handling Paper > Handling sheets > iPF825 Loading Sheets in the Printer 7 665
When inserted, sheets are automatically held by suction against the Platen. Important • Load a sheet so that it is parallel to the Paper Alignment Line at right (c). Loading paper askew will cause an error. • Warped paper may rub against the Printhead. Straighten paper if it is warped before loading it. Note • You can adjust the strength of suction holding paper against the Platen when the Release Lever is up. If it is difficult to load paper, press the ▲ or ▼ button on the Control Panel to adjust the strength. Set suction stronger by pressing the ▲ button or weaker with the ▼ button. Three settings are available. However, even if you increase the suction, it may not be sufficient to hold some types of paper against the Platen well. In this case, use your hand to load the paper. • Sheets are held in place by suction through holes on the Platen. Although the suction may produce a noise when paper is loaded in some positions, it does not indicate a problem. If the noise is distract- ing, try moving the paper over slightly to the left or right (up to 1 mm [0.039 in]) while keeping it parallel to the Paper Alignment Line. • The suction remains on for about 30 seconds during loading. If you cannot finish loading a sheet dur- ing this time, pull the sheet away and reinsert it to start the suction again. 3. Lower the Release Lever and close the Top Cover. The printer now starts feeding the paper. After the paper is advanced, the printer automatically goes online and starts printing. If no print job has been received from the computer beforehand, the printer automatically shows a menu for selection of the type of paper on the Display Screen. In this case, select the type of paper. (See "Selecting the Paper Type (Sheet) .") →P.663 Handling Paper > Handling sheets > Loading Sheets in the Printer iPF8257 666
Manually Loading Paper to the Position for Printing When printing on non-standard sizes of paper or to specify a particular position to start printing, in the printer menu set Width Detection to Off for the paper used. Setting Width Detection to Off will prevent paper from being automatically advanced to the position for printing. In this case, manually load paper at the position for printing. Instructions for manually loading paper at the position for printing when Width Detection is set to Off are as follows. 1. If you send a print job from a computer beforehand, the type and size of paper are shown on the Display Screen. Lift the Release Lever and open the Top Cover. Important • Do not touch the Linear Scale (a), Carriage Shaft (b), or Ink Tube Stabilizer (c). Touching these parts may damage them. Handling Paper > Handling sheets > iPF825 Manually Loading Paper to the Position for Printing 7 667
2. Keeping the right edge of the paper aligned with the extended line of the Paper Alignment Line (a) on the right side of the printer, load the paper so that the near edge is aligned with the groove (b) at the far end of the Platen. In this case, advance the paper as far into the paper feed slot as possible because it will be printed starting at that position. 3. Lower the Release Lever and close the Top Cover. 4. If no print job has been received from the computer, press ▲ or ▼ to select of the type of paper loaded, and then press the OK button. 5. When "Width Detection OFF. OK to continue?" is shown on the Display Screen, press ▲ or ▼ to select " Leave OFF " and then press the OK button. 6. Check the position of the loaded paper and press the OK button. 7. Press ▲ or ▼ to select the paper size, and then press the OK button.Handling Paper > Handling sheets > Manually Loading Paper to the Position for Printing iPF8257 668
Note • If a print job received requires paper larger than the selected paper, it may soil the Platen. Removing Sheets Remove sheets from the printer as follows. 1. Press the Load/Eject button. Note • Paper cannot be ejected by using the Load/Eject button when print jobs are in progress or during the ink drying period. Before ejecting paper, press the Stop button to cancel printing, print job process- ing, or ink drying. 2. Press the OK button to eject the paper. The paper is ejected from the front of the printer. Handling Paper > Handling sheets > iPF825 Removing Sheets 7 669
3. As you hold the sheet, lift the Release Lever and remove the sheet. 4. Lower the Release Lever. Handling Paper > Handling sheets > Removing Sheets iPF8257 670
Output Stacker Wheeled Output Stacker ................................................................................................................................. 671 Using the Wheeled Output Stacker ............................................................................................................. 671Wheeled Output Stacker An output stacker with casters, positioned in front of the printer. a. Output Stacker A cloth tray that catches ejected documents. The Output Stacker can be opened and closed using the rod in front. b. Output Stacker Ejection Guides Prevent printed documents from winding around the Roll Holder or being drawn into the Paper Feed Slot. Hold the Wheeled Output Stacker by these guides when moving it. c. Output Stacker Foot Stand Equipped with casters to facilitate moving it. d. Stopper Locks the Stand casters. Always release the Stopper before moving the printer. Moving the printer while the Stopper is locked may scratch the casters or the floor. Note • For instructions on assembling the Wheeled Output Stacker, see the setup guide provided with the Wheeled Output Stacker. Using the Wheeled Output Stacker Positioning the Wheeled Output Stacker by the printer will prevent rolls from dropping on the floor after printing. The stacker is equipped with casters to facilitate moving it. Important • The Output Stacker can accommodate one sheet. When printing multiple pages, remove each sheet after it is printed. Handling Paper > Output Stacker > iPF825 Wheeled Output Stacker 7 671
Positioning the Wheeled Output Stacker by the printer 1. Holding the Output Stacker Ejection Guides (a), move the stacker between the printer Stand. 2. Lock the casters. Handling Paper > Output Stacker > Using the Wheeled Output Stacker iPF8257 672
Removing the Wheeled Output Stacker from the printer Note • If there is not enough space to move the Wheeled Output Stacker, remove any printed documents inside the Output Stacker and fold the Output Stacker up. 1. Release the caster lock. Handling Paper > Output Stacker > iPF825 Using the Wheeled Output Stacker 7 673
2. Holding the Output Stacker Ejection Guides (a), move the stacker away from the printer. Handling Paper > Output Stacker > Using the Wheeled Output Stacker iPF8257 674