Vodavi Starplus 2448ex Hybrid Key Telephone System Installation Manual

							STARPLUS@ 2446EX 
Hybrid Key Telephone System 
APPENDIX B 
STARPLUS 2448EX PART NUMBERS 
Appendix B-l Starplus 2448W Component LSst 
. . 
PescnDtw 
Pati No, 
2448EX Basic Key Service Unit (KSU) 
Direct Station/Line Selector (DSs/DLS) 
2448EX Central Processor Board (CCU) 
Central Office Interface Board (COI) 
Key Station Interface Board (KSB) 
Single Line Telephone Interface Board (SIB) 
Single Line DTMFRS Unit (SLU) 
Applications Board (APB) 
Power 
Failure Transfer Unit (PFT) 
RS232C Module (RSM) 
2448EX Desc, Install, and Cper Manual 
2448EX Station Users Guide 
2448EX Attendant Users Guide 
2448EX SLT Users Guide 
2448EX DSSJDLS Numbered Designation Tabs 
External Power Supply Housing (EPH) 
Power Supply Unit (PS) 
Battery Charging Card (BC) 
Single tine Ring Generator (RG) 
DC/DC Converter (DC/DC) 
Bypass Board for External Power Housing 
Basic Key Telephone 
Enhanced Key Telephone 
Executive Key Telephone 
Phone Box (Ash) 
SP Wall Mount Kit 
SP Replacement Handset 
SP Button Caps 
SP Blank Designation Tabs 
SP Replacement 12 ft Handset Cord 
SP Directory Window for Basic Key 
SP Replacement 25 ft Handset Cord 
Where XX= SP2400-00 
SP241 O-XX 
SP2430-00 
SP2431-00 
SP2432-00 
SP2433-00 
SP2434-00 
SP2435-00 
SP2436-00 
SP2437-00 
SP2450-00 
SP2452-00 
SP2453-00 
SP2454-00 
SP2462-00 
SP2470-00 
SP2471-00 
SP2472-00 
SP2473-00 
SP2474-00 
SP2475-00 
SP61610-xx 
SP61612-00 
SP61614XX 
SP61616-44 
SP61640-xx 
SP61660-XX 
SP61662-00 
SP61664-00 
SP61666-xx 
SP61668-00 
P14108-XX 
OO= Black 
&Ash 
54= Gray 
60= Burgundy , 
Issue 3, August 1991 Appendix B-1  
						

							sTARPLlt!Sbb 2446EX Hybrid Key Telephone System 
APPENDIX C 
AEC The Messengerm 212 Plus 
Description 
AEC’s The Messenger 212 Plus, Dual-Line An- 
nouncer can be used to provide the Recorded 
Announcement feature of the 2446EX and the 
96EX Uniform Call Distribution feature (UCD) that 
provides unanswered incoming CO Calls or calls in 
queue with a recorded message while waiting for 
an available UCD station. 
The 2446EX and 96EX systems provide a program- 
mable option that allows the use of unused CO line 
positions, SLT ports as the specified RAN output 
port(s) or the APL RAN port (96EX only). Each 
UCD group may be programmed to connect a 
waiting caller to either the first or second RAN port 
for the initial message, then select the other RAN 
--I port, if connected, for the second and subsequent 
messages. 
Installation 
The Messenger 212 Plus can be connected to the 
2446EXorthe96EXinthefollowingconfigurations. 
- One or Two SLT ports. 
- One or Two CO line ports. 
- The APL RAN port (96EX only) and if 
needed one CO line port. 
The connection of each type of port requires dif- 
ferent installation practices and will be described For connection of the Messenger to either the APL 
RAN Port (96EX only) or to a CO line Port the 
separately. 
Messenger 212 Plus must be configured as follows. 
SLT Ports 
To install the 212 Plus using one or two SLT ports 
the following equipment is required and must be 
installed for proper operation. 
- An SLT Board (SP2433-00) or SIB board 
(SP4933-90) with available ports. 
- One APB Board (SP243500) or APL 
Board (SP4935-00). 
- One RG/MW power supply (SP2473-00) 
- One or two modular jacks (4 or 6 pin). When connecting the Messenger 212 Plus using 
one or two SLT ports the following options on the 
212 Plus unit must be set; 
1. Set the switches on the back of the unit as 
follows; 
Sl - off 
s2 - off 
s3 - off 
s4 - off 
2. The internal jumper plug of the Messenger 
212 Plus should be in its defautl line type 
setting of CO/PBX. This will match the SLT 
port(s) of the system and provide ring trip for 
the start of the message. 
NOTE: When the jumper plug of the Mes- 
senger 212 Plus is set to CO/PBX for the 
line type then both lines of the Messenger 
must be connected to SLT ports of the 
system. 
3. Connect the Voice Tip and Voice Ring from 
the “J” connector of the SLT port being used 
to a modular jack. Using the line cords 
provided plug in to the modular jack and one 
of the tine jacks in the back of the Mes- 
senger 212 Plus unit. (See figure 1) 
APL RAN and CO Line Ports 
1. Set the switches on the back of the Messenger 
212 Plus unit as follows; 
Sl -off 
s2 - off 
s3 - off 
S4 - on 
. 
Issue 3, August 1991 Appendlx C-l  
						

							STARPLUS@%@EX Hybrid Key Telephone System 
SIB AEC 
The Messenger 
212 Plus 
Figure C-1 SLT to AEC Connections 
2. The internal jumper plug of the Messenger 212 
Plus unit should be set to the first alternative 
setting for a 600 ohm transformer coupled 
audio output. Check the Messenger 212 Plus 
Owners Manual for procedures on changing 
the internal jumper plug. position on the back of the Messenger 212 
Plus unit. 
If an ACT 6 position to 6 position cord is not 
available use the wiring diagram in figure 2 as a 
guide to connect the Messenger 212 Plus unit to 
NOTE: Using the 600 ohm setting of the 
Messenger 212 Plus both lines of the Mes- 
senger must be connected to any combina- 
tion of the APL RAN output port (96EX 
only) or one or two CO line port(s). 
When installing the Messenger 212 Plus unit onto 
the 96EX System, both the APL RAN output port 
and a CO tine port can be used simultaneously. 
However connection of the Messenger to these 
ports is different. For this reason each type of 
installation will be described separately. 
APL RAN Port (96EX only) 
When the Messenger 212 Plus unit is installed 
using the APL RAN port the following equipment 
will be required. 
- An APL Board (SP4035-00) 
- An ACT 8 position to 6 position modular 
line cord. (98ACT462) 
1. To connect the Messenger 212 Plus to the 
APL RAN jack plug the 6 position end of the 
ACT modular line cord into the APL RAN Port 
(APL MOD 3 jack) then plug the 8 position 
end of the line cord into the line 1 or line 2 the APL RAN port. 
CO Line as a RAN Port 
To Install the Messenger 212 Plus using a CO Line 
port as the RAN output port the following equipment 
is necessary for a proper installation. 
- Unused CO line ports on a COI, COB or ~ 
COA Board. (SP2431-00 or SP4031-00 or 
SP4031-10) 
- Power Fail Transfer unit (SP2436-00) wifh 
Loud Bell Control for each CO port to be 
used. 
- 24 volt DC power supply to provide a fil- 
tered talk path (less than 1 amp is re- 
quired). 
- Two (2) 300 ohm l/4 watt resistors for 
each circuit. 
- One or two 8 conductor modular jacks 
and 8 conductor line cords. 
Appendix C-2 
Issue 3, August 1991  
						

							STARPLUS@ 2448EX Hybtid Key Telephone System 
APL 
Tin? 
STOP 1 
START 2 D 
VOICE 3 
VOICE 4 
START 5 
I B 
STOP 6 212 Plus 
%I%+ 
STOP 
STOP 
VOICE 
VOICE 
GROUND 
START 
Figure C-2 ACT 8 Cond. to 6 Cond. RAN Line Cord 
To install the Messenger 212 Plus using a CO 
circuit as the interface connect as described below. 
-. (see figure 3) 
1. Conned the 300 ohm resistor in series with 
the - (negative) lead of the 24 volt DC power 
supply and the CO tip on the “P” connector. 
2. Next connect the second 300 ohm resistor in 
series to the + (positive) lead of the power 
supply and the 8 position modular connector 
pin 5 (Tii / green). 
3. Then wire the ring lead from the “P” connector 
of the CO port being used to pin 4 of the 8 pin 
modular jack (Ring / red). 
4. Connect both of the LSC contact leads of the 
Power Fail Transfer unit to the START and 
GROUND leads of the 8 pin modular jack 
(pins 7 and 8). 
Connection 
of the Messenger 212 Plus to the sys- 
tem is now complete. Proceed with applying power 
and recording your message(s) 
as described in the 
Messenger 212 Plus Owners manual. 
,- . Programming It will be necessary to update the data base of the 
2448EX or 96EX system to include the RAN op 
tions. Depending on the application the following 
program codes will need to be updated. a Universal Call Distriiution (FLASH 19) lt is 
necessary to specify which RAN table(s) will be 
used for each UCD group assigned. This is 
done by pressing button 12 while in UCD 
programming. 
b UCD Timers (FLASH 33) The Ring timer (button 
1) determines how long an incoming CO call will 
ring into the UCD group before being answered 
and presented to the first message. 
The Message Interval Timer (MlT)(button 2) 
determines the duration of time the caller will 
be in queue and on hold between messages 
The OVeRflow timer (button 3) determines the 
total time, starting from when the call was 
answered, a caller will be kept in queue before 
being routed to the overflow station. 
c Announcement Tables, (FLASH 34) This deter- 
mines the type, index (port) number and length 
for the two available Recorded announcements 
(RAW 
When defining SLT port(s) or CO tine port(s) 
as the RAN output port it is most important to 
set the TIME parameter (length of the mes- 
sage) in the Announcement Table so that it is 
approximately one second longer than the ac- 
tual message. 
Issue 3, August 1991 Appendix C-3  
						

							STARPLUS@ 2448EX Hybrid Key Telephone System 
d When a CO line has been used it will be neces- 
sary to program an L5C contact to that par- 
ticular line. This is accomplished in Loud Bell 
Control assignments (FLASH 16). Assign the 
CO port to be used for the RAN operation to 
one of the LBC contacts. 
Refer to the Starplus 2446EX or 96EX Description, 
Installation and Operation manual for further in- 
structions on how to enter the program mode and 
additional information on the above listed program 
options. Also reference The Messenger Owner’s 
Manual for recording, battery operation and 
troubleshooting information. 
‘p’ Blodr (66 Type) 
) LBC 
I ---.--- I TerminaJs 
II - A 
Figure C-3 COB to AEC Connections 
Appendix C-4 
Issue 3, August 1991  
						

							TM 
kxl 
\/0i=1/4\/1 TECHNICAL FACT NOTICE 
TFN-024 
hiarch 6,1992 
CORRECTION TO STARPLUS 2448EX MANUAL, ISSUE 3, AUGUST 1991 
The following pages of the Starplus 2446EX Manual, Issue 3,August 1991, have been changed and should be 
replaced: 
Table of Contents, Page(s): iv, Issue Control Page. 
Section300 Page(s):30013,300-7,300-11,300-17 
Section 310 Page(s):3105 
Section 400 Page(s): 400-1, 400-4, 400-9. 
Section 500 Page(s):500-1, 500-7,500-21. 
Section 600 Page(s): 600-1, 600-7. 
Section 620 Page(s): 620-1, 620-3. 
Section 630 Page(s): 630-1, 630-7, 630-9, 630-11,630-12. 
Appendix A Page(s): A-9 
Page 1 of 1 
Vodavi Communications Systems 8300 E. Raintree Drive Sconsdale,Az 85260 (802)443-6000