Vodavi Starplus 2448ex Hybrid Key Telephone System Installation Manual

							Hybrid Key Telephone System STARPLUS@%WEX 
PROGRAM CODE 
BEN FEATURE DEFAULT VALUE 
(after initializina) 
FLASH 21 1 
SMDR 
NO (disabled) 
FLASH 26 
FLASH 27 
FLASH 26 
FLASH 29 
FLASH 30 
FLASH 31 
FLASH 32 
FLASH 33 1 
2 
1 3 
FLASH 34 
FLASH 35 Dedicated Attendant Intercom Path 
Background Music 
Settincr Date and Time 
ISLT Hookswitch Timer 
~ SLT Hookswitch Bounce Timer 
Yes 
Yes 
M/D:1 2 HR 
10 (1 sec.) 
010 msec. 
Voice Mail Outpulsing Tables l-7 
Voice Mail Disconnect Table 6 Disconnect Table is empty by 
660-2 
Issue 3, August 1991  
						

							sThAPLUS??4l8EX Hybrid Key Telephone System 
--. 
Initialize Data Base Parameters (Cont’d) 
660.2 INITIALIZE CO LINE AlTRIBUTES 
Pfugramming Steps 
If the system is in the programming mode, continue 
using the program codes. lf starting to program here, 
enter&e programming mode. (Refer to Sec. 600.3). 
If CO Line Attributes need to be initialized: 
1. Press FLASH and dial [71]. The following mes- 
sage will be shown on the display phone: Description 
The CO Line parameters may be initialized setting 
all data fields to their original, defautt values. Th8 
following data fields are returned to their default 
value upon initializing the CO tine parameters: 
2 To initialize the CO tine Attributes, press the 
HOLD button. Confirmation tone will be heard. 
? 
PROGRAM CODE  
						

							Hybrid Key Telephone System 
Initialize Data Base Parameters (Cont’d) 
660.3 INITIALRE STATION AlTRIBUTES 
Programming Steps 
If the system is in the programming mode, continue 
using the program codes. If starting to program here, 
enter the programming mode. (Refer to Sec. 600.3). 
If Station Attributes need to be initialized: 
1. Press flASH and dial [72]. The following mes- 
sage will be shown on the display phone: Description 
The Station parameters may be initialized setting all 
data fields to their original, default values. The fol- 
lowing data fields are returned to their default value 
upon initializing the Station parameters: 
, 
2. To initialize the Station Attributes, press the 
HOLD button. Confirmation tone will be heard. 
PROGRAMCODE 
FLASH 50, Paoe A FLEX 
FEATURE DEFAULT VALUE 
BUTTON (after initializing) 
A/l Pasing Access Allowed (enabled) 
A/2 Do Not Disturb Allowed (enabled) 
A/3 Svstem Speed Access Allowed (enabled) 
A14 Queuing Access Allowed (disabled) 
At5 Preferred Line Answer Dis-allowed (disabled) 
AI6 SLT Conference Allowed (enabled) 
At7 Call Forward Allowed (enabled) 
A/8 Forced LCR Dis-allowed (disabled) 
Al9 LCR Class of Service Not required(disabled) 
All Key Station defauft to Station ID 
0 (keyset) 
B/l Station ID AU Single Line Telephones 
default to ID 4 
(SLT w/o MSG Wait) 
8/2 Station Class of Service All Stations assigned COS 1 
B/3 Speakerphone Option All Stations assigned option 1 
B/4 Group Pick-Up Assionment(s) All Stations assigned into Group 1 
B/5 Paging Zone(s) Assignment(s) All Stations assigned into 
Zone 1 
B/6 Preset Forward Destination None assinned 
B/7 CO Line Group Access All Stations assigned access to 
I Grnm I 
FLASH 50, Page B 
1 B/8 1 flex Button Assignment 
1 See default button assignment 1 
666-4 issue 3, August 1991  
						

							Hybrid Key Telephone System 
FLEX 1 FLEX 2 
FLEX 5 FLEX 6 
FLEX 13 FLEX 14 FLEX 15 FLEX 16 
u 
SPD 
3t THIS BUlTON IS MAPPED AS A LOOP BUlTON ON THE BASIC KEYSET 
Figure 660-l 2448EX Default Button Mapping 
Issue 3, August 1991 
660-6  
						

							Hybrid Key Telephone System 
Initialize Data Base Parameters (Cont’d) 
660.4 INITIALQE EXCEPTION TABLES 
Programming Steps 
If the system is in the programming mode, continue 
using the program codes. If starting to program here, 
enter the programming mode. (Refer to Sec. 600.3). 
If Exception Tables need to be initialized: 
I. Press FLASH and dial [73]. The following mes- 
sage will be shown on the display phone: Description 
The Exception Table parameters including the Al- 
tow/Deny Tables and the Special Tables may be 
initialized setting all tables to their original, 
default 
values. The following Tables are cleared returning 
to their default value upon initializing the Exception 
Tables parameters; 
2. To initialiie the Exception Tables, press the 
HOLD button. Confirmation tone will be heard. 
PROGRAM CODE FLEX 
I PI ITTfihl I FEATURE 
FLASH 60 1 Allow Table A 
2 Deny Table A 
3 Allow Table B 
4 Deny Table B 
I 5 1 Special Table 1 
I 6 1 Special Table 2 
7 Special Table 3 
8 Special Table 4 (Home Area Code) Table Cleared (no entries) 
Table Cleared (no entrfes) 
Table Cleared (no entries) 
Table Cleared (no entries allowed, 
no area code specified) 
Table Cleared (no entries allowed, 
no area code specified) 
Table Cleared (no entries allowed, 
no area code specified) 
Table Cleared (no entries allowed) 
6696 Issue 3, August 1991  
						

							lnitiallre Data Base Parameters (Cont’d) 
660.5 lNlllAUZE SYSTEM SPEED 
Programming Steps 
Description 
If the system is in the programming mode, continue 
using the program codes. If starting to program here, 
enter the programming mode. (Refer to Sec. 600.3). 
If System Speed bins need to be initialiied: 
1. Press FLASH and dial [74]. The following mes- 
sage will be shown on the display phone: Numbers entered into the System Speed dial Table 
may be Waked clearing all bins to their original, 
default value (empty). All bins 20 through 99 are 
cleared returning to their default value (empty) upon 
initial&g the Speed Dial Table. 
2. To initialize the System Speed bins, press the 
HOLD button. Confirmation tone will be heard. 
7 
Issue 3, August 1991 660-7  
						

							. 
Hybrid Key Telephone System %ARPLUS%448~ 
Initialize Data Base Parameters (Cont’d) 
660.6 INITlALlZE LCR TABLES 
Programming Steps Description 
If the system is in the programming mode, continue The LCR Tables may be initialized setting all tables 
using the program codes. If starting to program here, to their original, default values. The following tables 
enter the programming mode. (Refer to Sec. 600.3). will be reset to their original default value after initiali- 
If LCR Tables need to be initialized: zation of the LCR tables: 
1. Press RASH and dial [7q. The following mes- 0 
sage will be shown on the display phone: 
0 
2. To initialize the LCR Tables, press the HOLD 
button. Confirmation tone will be heard. Exception Table 
s-Digit table 
6-Diiit Table 
Route List Table 
Daily Start Time Table 
Weekly Schedule 
Insert/Delete Table 
PROGRAM CODE FLEX FEATURE DEFAULT VALUE 
( 
Q) L  BUTTON after initializin 
FLASH 61 1 3-Digit Routing Table Default 
2 6-Digit Routing Table None 
3 Exception Code Table 
4 Route List Table 
5 Insert/Delete Table 
6 Daily Start Time Table 
7 Weekly Schedule Table 
660-a issue 3, August 1991  
						

							STARPLUS@ 2446EX 
Hybrid Key Telephone System 
SECTION 670 
SYSTEM DATA BASE PRINTOUTS 
670.1 PRINT ENTIRE SYSTEM DATA BASE 
Programming Steps 
If the system is in the programming mode, continue 
using program codes. If starting to program here 
enter the programming mode 
first (refer to paragraph 
600.3). 
If a complete printout of the entire data base is 
desired: 
1. Press FLASH 
and dial [80]. The following mes- 
sage will be shown on the display of a display 
phone: 
2. To print the entire data base, press the HOLD 
button. The display will update to indicate what 
portion of the data base is being printed. 
When the system has finished sending the entire 
data base to the printer, confirmation tone will be 
heard. Description 
With a printer connected to the RS232C port, of the 
CCU, the currently stored customer data base can 
be printed or tploaded” into a file. This command 
allows the entire data base to be “dumped” as a 
permanent record which can serve as a hard copy 
of the data base. 
The system Baud rate must match that of the printer 
or receiving device. 
Refer to section 610.20 for 
instructions on viewing or changing the baud rate in 
the 2448EX system. 
Printing the entire data base takes a while to print. 
The data base is printed in the following order: 
- All System Parameters 
- All CO Line programming (CO tines 01-24) 
- All Station attributes (Stations 10-n) 
- Toll Tables (allow, deny and special tables) 
- System Speed Dial Numbers (bins 20-99) 
- LCRTables 
Refer to the following Figures for examples of the 
data base printouts. Also refer to the following para- 
graphs for instructions on printing only portions of 
the data base. 
Issue 3, August 1991 670-l  
						

							A Hybrid Key Telephone System wARPLUS@ 2448EX 
System Data 
Base Printouts (Cont’d) 
670.2 SYSTEM PARAMETERS 
Programming Steps 
If the system is in the programming mode, continue 
using program codes. If starting to program here 
enter the programming mode first (refer to paragraph 
600.3). 
If a printout of all System Parameters is desired: 
1. Press FLASH and dial [81]. The following mes- 
sage will be shown on the display of a display 
phone: 
2. To print the system parameter data base, press 
the HOLD button. The display will update. 
When the system has finished sending the informa- 
tion to the printer confirmation tone will be heard. Description 
With a printer connected to the RS282C port, of the 
CCU, the currently stored customer data base can 
be printed or “uploaded” into a file. This command 
allows the System Parameters data base to be 
“dumped” as a permanent record which can serve 
as a hard copy. 
The system Baud rate must match that of the printer 
or receiving device. Refer to section 610.20 for 
instructions on viewing or changing the baud rate in 
the 2448EX system. 
When printing the System Parameters the following 
data is printed; 
l All System Timers 
l All System wide options (i.e. external night 
ringing, Hold preference etc...) 
l Attendant programming 
l Other system assignments (i.e. Loud bell, 
ExecutiveSecretary, SMDR etc...) 
l UCD group and associated programming 
l Voice Mail Group and associated program- 
ming 
Refer to the following Rgure for 
an example of the 
system parameters data base print out. 
670-2 
Issue 3, August 1991  
						

							t 
1 ~AAPLUS@ 2448EX 
Hybrid Key Telephone System 
I HFT HFD DAC HPR PRI ENR 
10 10 100 SYS Y N 
1 90R INT BGM LCR PWT 
Y Y Y N Y 
i WIENDANT STATIONS 
10 ## Pi 
I ;OUD BELL ASSIGNMENTS 
### C## 
?BX DIALING CODES 
I# C# II# #I ## 
ZECUTIWUSECRETARY PAIRINGS 
. = 
! = 
z: 
f i 
I = 
: = 
ii d;: 
;;ALT OVRANO STN# 
I91 
192 
193 
194 
‘95  E 
E 
a 
8 
I 8 
8 
UN 
R 
96 
97 
CD TIMERS 
ING MIT OVER 
60 60 60 
Data Base Printout 
Desctiption 
7A MONITOR Eng. Ver. l.lf 
DATE: 07/24/91 TIME: 14:10:43 
ENTER PASSWORD: 
adm-, ENTER PROGRAM NO 
adm.81 PRINT SYS PARAM 
PRESS HOLD 
admz 
SYSTEM PARAMETERS 
Eng. Ver. 1.lf 
SHR EHR 
XFR PFT PT CPT 60 180 45 
10 2 
180 
CFT MWT PTO COT ART ICM SRT 
10 0 15 3 1 20 20 
SHR= System Hold Recall Timer 
H-R= Exclusive Hold Recall Timer 
XFR= Transfer Recall Timer 
PFT= Preset Forward Timer 
PT= Pause Timer 
CPT= Call Park Timer 
CFN= Call Forward No-Answer Timer 
CFT= Conference Timer 
MWT= Message Wait Reminder Tone 
PTO= Page Timeout Timer 
COT= CO Ring Detect Timer 
ART= Attendant Recall Timer 
ICM= Phone Box Timer 
SRT= Single Line Receiver Timer 
HFT= Hook flash Timer 
HFD= Hookswiich Bounce Timer 
DAC- DISA Access Code 
HPR= Hold Preference 
ENR= External Night Ringing 
AOR= Attendant Override 
INT= Dedicated Attendant Intercom 
BGM= Background Music 
LCR= LCR Enable/Disable 
PWT= Page Warning Tone 
UCD= Uniform Call Distribution 
ALT= UCD Alternate UCD Group 
OVR= UCD Overflow Station 
ANO- Announcement Tables Index 
STN#= UCD Station Numbers 
RING= UCD Ring Timer 
MIT= UCD Message Interval Timer 
OVER= UCD Overflow Timer 
Figure 67&l DB Printout of System Parameters