Panasonic Kx-Td308 Digital Super Hybrid System Installation Maintenence Manual

							AFlow Chart of the ARS procedureA long distance call is made.
$
Toll Restriction CheckRestricted
Not Restricted
Is the ARS Access Code (Default: 9) dialed?
YesNo
Obtains an applicable Route Plan Table
number from the Leading Digit Table.The call is routed via an idle line.
Plan Table by the current time of day.
I
Is there any line available in the outside line of
priority 1 ?IJ
YesNo3
Obtains an applicable ModificationYesYesIs the outside line of priority 2
b Table number for the outside lineassigned in the Route Plan Table?
4
Modifies the digits.
4
Call.
Is there any line available in the
outside line of priority 
2?
No
Is the outside line of priority 3
assigned in the Route Plan Table?
No
No
Yes
Is there any line available in the
outside line of priority 
3?NoWSends a busy tone.
3-11 
						

							A3.Features
Automatic Station Release
DescriptionAfter going off-hook, if an extension user fails to dial any digits
within a specified time period, the user will be disconnected from
the line after reorder tone is sent. To get a-line again, the user must
go back on-hook and then off-hook.
ConditionsThis function works in the following cases:
When making a call
(l)The first digit has not been dialed within 10 seconds.
(2)After a digit is dialed, the next one is not dialed within five
seconds (Intercom call only).
Programming References
Section 4, System Programming
[207] First Digit Time
[208] Inter Digit Time
Feature ReferencesNone
Operation References Not applicable.3-12Features 
						

							FeaturesB
Background Music (BGM)
DescriptionAllows the proprietary telephone user to listen to background music
from the monitor speaker on the telephone.
Conditiqns. It is required to connect a user-supplied external music source, such as
a radio. One external music source can be connected to the system.
l The music source is used for BGM and/or Music on Hold. It is also
possible to disable the BGM and/or Music on Hold.
l The music is interrupted when you go off-hook.
Connection References
Section 2, Installation
2.3.8 External Music Source Connection
Programming References
Section 4, System Programming
[803] Music Source Use
[990] System Additional Information, Field (20)
Feature ReferencesSection 3, Features
Music on Hold
Operation References DPT Features-User Manual
Background Music (BGM)
Features3-13 
						

							BFeatures
Background Music (BGM) - External
DescriptionBackground music (BGM) can be broadcast in your office through
the external pagers.The BGM can be turned on and off by the
operator or manager.
Conditionsl It is required to connect an external pager and an external music source.
The pager and the external music source are user-supplied items. One
pager and one external music source can be installed to the system.
l Each pager can be programmed to send BGM or not.
l Priority of access to external pager is: (1)TAFAS; (2)Paging; (3)BGM
Higher priorities will override the BGM.
Connection References
Section 2, Installation
2.3.7 External Pager (Paging Equipment) Connection
2.3.8 External Music Source Connection
Programming References
Section 4, System Programming
[ 1001 Flexible Numbering, Background music - external
[803] Music Source Use
[804] External Pager BGM
[990] System Additional Information, Field (20)
Feature ReferencesSection 3, Features
Background Music (BGM)
Operation ReferencesOperator / Manager Service Features-User Manual
Background Music (BGM) - External
3-14Features 
						

							FeaturesB
Bilingual Display
DescriptionProvides the display proprietary telephone user with either an
English or French display. Either display 
can be selected by Station
Programming.
ConditionsNone
Programming References
Station Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .User Manual
Bilingual Display Selection
Feature ReferencesNone
Operation References Not applicable.
Busy Lamp Field
DescriptionThe LED (Light Emitting Diode) indicators of the DSS (Direct
Station Selection) buttons, each of which corresponds to a selected
extension, tell whether the corresponding extensions are idle or
busy.
Conditionsl This function is available for flexible CO buttons assigned as DSS
buttons on proprietary telephones.
l A DSS button indicator lights red if the corresponding extension is
busy.
Programming References
Section 4, System Programming
[005] Flexible CO Button Assignment
Station Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . User Manual
Flexible CO Button Assignment - Direct Station Selection (DSS) Button
Feature ReferencesSection 3, Features
Button, Direct Station Selection (DSS)
Operation References Not applicable.
Features3-15 
						

							BFeatures
Busy Station Signaling (BSS)
DescriptionWhen attempting to call a busy extension (ringing or having a
conversation), Busy Station Signaling allows you to signal the user
on the phone to answer your call. The called extension user hears a
Call Waiting tone and is able to answer the call.
Conditions
l This feature only works if the called extension has activated Call
Waiting. If Call Waiting is activated, the caller will hear ringback tone;
if not, the caller will hear a reorder tone.
l If the called party is provided with the Off-Hook Call Announcement
(OHCA) function, the caller can announce the call through the speaker.
Programming References
Section 4, System Programming
[990] System Additional Information, Field (37)
Feature ReferencesSection 3, Features
Call WaitingOff-Hook Call Announcement
(OHCA)
Operation ReferencesDPT Features, Standard Telephone Features-User Manual
Busy Station Signaling (BSS)
3-16Features 
						

							3FeaturesB
Button, Direct Station Selection (DSS)
DescriptionDSS button permits the proprietary telephone user one-touch access
to other extension users.
Conditions
l A flexible CO button on a proprietary telephone can be assigned as a
DSS button using either System or Station Programming.
l Once a button is assigned as a DSS button, it provides Busy Lamp Field
(BLF) status.
l The mode of a DSS button can be programmed to disconnect the
outside line and calls the extension or hold and transfers the call to the
extension (One-Touch Transfer by DSS Button).
Programming References
Section 4, System Programming
[005] Flexible CO Button Assignment
[ 1081 Automatic Hold by CO / DSS Button
Station Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .User Manual
Flexible CO Button Assignment 
- Direct Station Selection (DSS) Button
Feature ReferencesSection 3, Features
Busy Lamp FieldOne-Touch Transfer by DSS
Button
Operation References Basic Operation-User Manual
Making Calls
DPT Features
Call Transfer - to ExtensionFeatures
3-17 
						

							B3Features
Button, Flexible
DescriptionConditionsThe use of Flexible Buttons is determined by either System or
Station Programming. The following two types of Flexible Buttons
are provided on analog or digital proprietary telephones
(APT/DPT):
l Flexible CO buttons
l Programmable Feature (PF) buttons (provided on APT only)
The table below shows all of the features which can be assigned to
Flexible Buttons.
( 
AP’I?‘DPT)
Direct Station Selection (DSS)d_______-_---------------------------------------
Single-COd______________---__-----------------------------
Live Call Screening?r/__________________------------------------------
Live Call Screening Canceltv_________-_-_-----------------------------------
Log-In / Log-Outc/_______________--__-----------------------------
Loop-CO(/__________--_-----------------------------------
Message Waiting(/_________-_-___---------------------------------
Phantom Extension(/___________-___--__-----------------------------
Two-Way Record?d______-___--------------------------------------
Two-Way Transfer?(/__________________------------------------------
Account Code Entryd__________--_-----------------------------------
Conference(/_________---_-----------------------------------
FWD/DND(/___________-___---------------------------------
One-Touch Dialing(/______________----------------------------------
Saved Number Rediald_______________-___-----------------------------
Voice Mail Transferd
PF
NT
_---------------
1_---------------
1_---------------
1________________
_---------------
1_---------------1_---------------
_---------------
1.---------------
1____-___________
(/_---------------_
r/_----------------
(/_----------------
d.----------------
I/.----------------
r/
“4’ indicates that the feature is available.
l An outside line can only appear on one Single-CO button of any given
telephone. A station can only appear on one DSS button of any given
telephone.
l Incoming and outgoing calls on the line are shown on the button in the
following priority.
Single-CO 
> Loop-CO
3-18Featurest: Available when the Digital Super Hybrid System is connected to a Digital
Proprietary Telephone capable Panasonic Voice Processing System (one
that supports digital proprietary telephone integration; e.g. KX-TVS 100). 
						

							3FeaturesB
Programming References
Section 4, System Programming
[005] Flexible CO Button Assignment
StationProgramming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UserManual
Flexible CO Button Assignment
Feature, ReferencesSection 3, Features
Buttons on Proprietary Telephones
Operation References Not applicable.Features
3-19 
						

							33Features
Button, Loop-CO (L-CO)
DescriptionAll outside lines can be assigned to a flexible CO button on a
proprietary telephone (PT). The assigned button serves as a 
Loop-CO (L-CO) button. An incoming call on any outside line arrives at
the L-CO, unless there is a S-CO button associated with the line or
unless the button is already in use. To make an outside call, the PT
user simply press the dedicated L-CO button.
Conditionsl No L-CO button is originally provided on a PT. A flexible CO button
can be assigned as an L-CO button in either System or Station
Programming.
l It is possible to assign more than one L-CO button on a PT.
l Pressing the L-CO button provides the same operation as dialing an
automatic line access code. This results in Automatic Line Access or
Automatic Route Selection (ARS), if programmed.
l Immediate, delayed, no ringing or no incoming call (disable) can be
selected on an extension-outside line basis.
l The digital PT user can choose a desired ringer frequency for each L-
CO button by System or Station Programming.
Programming References
Section 4, Systeni Programming
[005] Flexible CO Button Assignment
[400] Outside Line Connection Assignment
[603]-[604]DIL 1 :N Extension and Delayed Ringing - Day / Night
[605]-[606]Outgoing Permitted Outside Line Assignment - Day /
Night
StationProgramming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . User Manual
Flexible CO Button Assignment - Loop-CO (L-CO) Button
Ringing Tone Selection for CO Buttons
Feature ReferencesSection 3, Features
Answering, Direct Outside Line
LED Indication, Outside Line
Line Access, AutomaticLine Access, Direct
Ringing, Delayed
Ringing Tone Selection for CO
Buttons
Operation References Basic Operation-User Manual
Making CallsReceiving Calls
DPT Features
Outward Dialing - Line Access, Automatic3-20Features