Panasonic Kx-Td308 Digital Super Hybrid System Installation Maintenence Manual

							Default Values
i2 13jDISA Delayed Answer Time1 ring
[216]Message Waiting Ring Interval Time0 min (no ring)
[2 171Timed Reminder Alarm Ring Time30 s
[218]DISA AA Wait Time1s
[2 191Call Park Recall Time12 rings
TRS / ARS Programming
[300]TRS Override for System SpeedDisable
Dialing
[301]-[305] TRS Denied Code Entry forNot Stored
Levels 2 through 6
[306]-[310] TRS Excepted Code Entry forNot Stored
Levels 2 through 6
[3 1 l]Special Carrier Access CodesNot Stored
List
5-5
. 
						

							520Default Values
Assignment
[402]Dial Mode SelectionAll Outside Lines=DTMF
[403]Pulse Speed SelectionAll Outside Lines=10 pps
[404] DTMF TimeAll Outside Lines=80 ms
[405]CPC Signal Detection Incoming SetAll Outside Lines=400 ms
[406]Caller ID AssignmentAll Outside Lines=Disable
[407]-[408] DLL 1: 1 Extension-Day/NightAll Outside Lines=Disable-Day/Night
[409]-[410] Intercept Extension-Day/NightAll Outside Lines=Disable-Day/Night
[41 l]Host PBX Access CodesNot Stored
f4 121 Pause TimeAll Outside Lines=l.5 s
[4 131Flash TimeAll Outside Lines=600 ms
[4 141Disconnect TimeAll Outside Lines=1.5 s
[415]CPC Signal Detection Outgoing Set
Disable
[4 161Reverse Circuit AssignmentRegular
[4 171Outside Line Name AssignmentNot Stored
cosProgramming
[500]-[501] Toll Restriction Level-Day/COS 1 through 7=Level l-Day/Night;
NightCOS 8=Level7-Day/Night
[502]Extension-to-Outside Line CallAll COS=Disable
Duration Limit
[503]Call Transfer to Outside LineAll COS=Disable
[504]Call Forwarding to Outside LineAll COS=Disable
[505]Executive Busy OverrideAll COS=Disable
[506]Executive Busy Override DenyAll COS=Enable
[507]Do Not Disturb OverrideAll COS=Disable
F5081Account Code Entrv ModeAll COS=Ontion
.
5-6List 
						

							52lDefault ValuesRinging-Day/Night
Ringing-Day/Night
[605]-[606] Outgoing Permitted OutsideAll Jacks- 1/2=All Outside
Line Assignment-Day/NightLines=Enable-Day/ Night
[607]-[608] Doorphone Ringing AssignmentJack 1-l=Enable; Other Jacks=Disable-Day/Night
-Day/Night
[609]Voice Mail Access CodesNot Stored
‘[6 171Live Call Screening Recording Mode All Jacks=Stop Ret
Assignment
Resource Programming
[800]SMDR Incoming / Outgoing Call
Outgoing Calls=All; Incoming Calls=On
Log Printout
[801] SMDR Format
[802]System Data Printout
18031Music Source Use
[804]External Pager BGM
[805] External Pager Confirmation Tone
[806]Serial Interface (RS-232C)
Page Length=66; Skip Perforation=0
Not Applicable
Hold and BGM=Enable
All External Pagers=Disable
On
New Line Code=CR+LF; Baud Rate=9600;
ParametersWord 
Length=8; Parity Bit=Mark; Stop Bit=1
[8 131Floating Number AssignmentPager==196; DISA=198;
E-Group 1=191; E-Group 2=192;
E-Group 3= 193; E-Group 4= 194;
E-Group 5=29 1; E-Group 6=292;
E-Group 7=293; E-Group 8=294
[8 151DISA Built-in Auto AttendantDisable
Optional Programming
[900]System Data ClearNot Applicable
[990]System Additional InformationSee pages 4-144 through 4-148.
[991]COS Additional InformationSee page 4- 150.‘_
f: Available when the Digital Super Hybrid System is connected to a Digital
Proprietary Telephone capable Panasonic Voice Processing System (one
that supports digital proprietary telephone integration; e.g. KX-TVSlOO).
List5-7 l 
						

							Section 6
Troubleshooting
This section provides information for system and telephone
troubleshooting. 
						

							61lTroubleshooting
6.1.1 Installation
PROBLEMPROBABLE CAUSEPOSSIBLE SOLUTION
Extension does not operate.Bad printed circuit boardExchange printed circuit board for
(Extension Card).another printed circuit board.
Bad connection betweenTake the extension and plug it into
the system and extension.the same extension port using a
short telephone cord. If the
telephone does not work, the
connection between the system and
the extension must be repaired.
A telephone with an A-AlUse a 2 wire cord.
relay is connected.Set the A-Al relay switch of the
telephone to the “OUT” or “OFF”
position.
Bad extension.Take the extension and plug it into
another extension port that is
working. If the telephone does not
work, replace the phone.
lrnproper reset operation.Press the Reset Button.
Noise in external paging.Induced noise on the wireUse a shielded cable as the
between the system and theconnection wire between the
amplifier.system and amplifier. A short
shielded cable is recommended.
Volume distortion from
external music source.Excessive input level fromDecrease the output level of the
external music source.external music source by using the
volume control on the music
source.
Speed Dialing or 
One-
Touch Dialing does not
function.Bad programming.Enter the outside line access
number (9,Sl through 83) into pro-
gramming.
6-2Troubleshooting
. 
						

							610Troubleshooting6.1.2 Connection
Connection between the system and a proprietary telephone:
Yes
(Continued on the
following page.)
CAUSE
The T/R is connected to the Dl/D2.
pz*xj
IIIIKX-TD308
extension
SOLUTION
Use the correct cord (inner 2
wires are for T/R and the
outer 2 wires are for Dl/D2).
Connection between the system and a standard telephone:
CAUSESOLUTION
The T/R is connected to the DlID2.
1KX-TD308
extension
Use the correct cord (inner 2
wires are for T/R).
Connection between the system and a standard telephone that is 
polarity-
sensitive:
L
4
The‘T’ is connected to the “R”.
Fq+;:KX-TD308
extension
SOLUTION
Reverse the connections of
the T/R.Troubleshooting
.
6-3 
						

							610Troubleshooting
Connection between the central office and the system:
(Continued from the
previous page.)
Outslde lmes are connected to the T2/Tl.
Can you dial
out on an
outside line?No
Outside lineKx-TD308
I
Outside lines are connected to the T2/Rl.
IOutside lineKx-TD308
6.1.3. Operation
SOLUTION
Reconnect the outside lines
totheTl/Rl orTUR2ofthe
telephone jack using 2-
conductor wiring.
PROBLEMPROBABLE CAUSE
POSSIBLE SOLUTION
l When using the speaker-. The HANDSET /l When the headset is not used, set
phone mode with aHEADSET selector ofthe HANDSET 
/ HEADSET
proprietary telephonethe KX-T7130 or 
KX-selector to the “HANDSET”
KX-T7 130 or KX-T7030,T7030 is set to the
position.
nothing is audible.
“HEADSET’* position.
l When using the speaker-* The “HEADSET’* model When the headset is not used,
phone/monitor mode with
is selected by Stationselect the “HANDSET” mode by
a DPT, KX-T722O/KX-Programming,“Handset/Station Programming.
T7230/KX-T7235/KX-T7 Headset Selection”.
250, nothing is audible.
The unit does not ring.The Ringer VolumeSet to “HIGH” or “LOW’.
Selector is set to 
“OFF.
6-4Troubleshooting
. 
						

							61lTroubleshooting
PROBLEM
PROBABLE CAUSEPOSSIBLE SOLUTION
During a power failure,l A DPT or APT isl Disconnect the DPT or APT and
extensions connected toconnected to the jack.connect a standard telephone.
jack numbers 1 do not
l The dialing mode (tonel Set the Tone / Pulse switch to the
operate.or pulse) is improper.other position.
Originating an outside call,The corresponding COProgram the CO button. See
Call Transfer, orbutton does not exist on the
Section 4.2 
[005] “Flexible CO
Conference cannot beproprietary telephone.Button Assignment”.
performed.
6.1.4Using the Reset Button
If the system does not operate properly, use the Reset Button.
Before using the Reset Button, try the system feature again to
confirm whether there definitely is a problem or not.
Pressing the Reset Button causes the following:
1. Camp-on is cleared.
2. Calls on Hold are terminated.
3. Calls on Exclusive Hold are terminated.
4. Calls in progress are terminated.
5. Call Park is cleared.
All other data stored in memory is not cleared.
Operation
If the system does not operate properly,
1. Press the Reset Button with a pointed tool.
When 
the power supply stops, certain extension is automatically
connected straight to specific outside line:
Extension
(T, R)of jack number1. . . . . . . . . . . . . . . . . . . . . . . . . CO1
Connect a standard telephone to the above extension jack.
Troubleshooting
.
6-5 
						

							Matsushita Consumer Electronics
Company, Division of Matsushita
Electric Corporation of America
One Panasonic Way, Secaucus,
New Jersey 07094
Panasonic Saks Company (LTSC’9),
Division of Matsushita Electric of
Puerto Rico, Inc.
Ave. 65 de Infantereia, Km. 9.5,
San Gabriel Industrial Park, Carolina,
Puerto Rico 00985
Printed in the United KingdomPSQX1348ZA SO997MTO (M)