Panasonic Kx-Td308 Digital Super Hybrid System Installation Maintenence Manual

							3FeaturesL” b
LED Indication, Outside Line
DescriptionThe LED (Light Emitting Diode) indicators of the buttons
associated with outside lines show the line conditions with a variety
of lighting patterns. This allows the user to see which lines are idle
and which lines are in use. The table below shows the lighting
pattern for different line conditions.
Flashing light patterns
Slow flashing
Moderate flashing
Rapid flashing
Conditions
LED IndicatorOutside Line StatusOff
Idle---
Green On
Green slow flashing
Green moderate
flashing
Green rapid flashing
Red On
Red slow flashingI-use
I-hold
I-Exclusive Hold 
/ Outside-to-outside
line call 
/ Unattended Conference
Hold Recall 
/ Privacy Release possible /
Incoming call
Other-use 
/ Log-Out
Other-hold
iiI
iI
l Red slow flashing indication appears on the S-CO button only.
l The indication of Privacy Release appears on the S-CO button only.
Programming References
Section 4, System Programming
[005] Flexible CO Button Assignment
Station Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .User Manual
Flexible CO Button Assignment 
- Loop-CO (L-CO) Button,
Single-CO (S-CO) ButtonFeatures
3-91 
						

							LFeatures
Feature ReferencesSection 3, Features
Button, Loop-CO (L-CO)
Operation References Not applicable.
Button, Single-CO (S-CO)
Limited Call Duration
DescriptionLimited Call Duration is a system programmable feature that
disconnects an outside call when a specified timer expires. A
warning tone is sent to the extension user 15 seconds, 10 seconds,
and 5 seconds before the time-limit. Limiting the call duration can
be activated or deactivated by Class of Service (COS) for each
extension.Conditions
l Any outside call except outside-to-outside line call is limited by this
feature. For outside-to-outside line calls, Outside-to-Outside Line Call
Duration is activated.
l It is programmable to select the limited call, either incoming and
outgoing call or outgoing call only.
Programming References
Feature References
Operation References
Section 4, System Programming
[205] Extension-to-Outside Line Call Duration Time
[502] Extension-to-Outside Line Call Duration Limit
[990] System Additional Information, Field (12)
Section 3, Features
Call Forwarding -to Outside LineConference, Unattended
Call Transfer, Screened 
- to
Outside Line
Not applicable.
3-92Features 
						

							3FeaturesL. .
Line Access, Automatic
DescriptionAllows the extension user to dial the automatic line access number
and access an idle line from the outside line assigned for the
extension. The proprietary telephone user can use the Loop-CO
button in place of the access number.
Conditionsl This feature functions with Automatic Route Selection (ARS), if ARS
is activated If so, the least expensive route is automatically selected.
l Each extension is subject to System Programming items for outside
lines available to access.
l The outside line hunting sequence is determined by System
Programming.
l This feature requires a CO button (L-CO or S-CO) assignment on a
proprietary telephone 
(PT). Dialing the line access code selects a CO
button on a 
PI according to the priority:
S-CO 
> L-CO (on a hunted outside line)
l If Idle Line Preference - Outgoing is set on tbe telephone, the user can
access an idle line only by going off-hook.
l The system waits for a programmed time before dialing after an outside
line is seized.
Programming References
Section 4, System Programming
[ 1001 Flexible Numbering, Automatic line access / ARS
[ 
1031 Automatic Access Outside Line Assignment
[21 l] Dial Start Time
[4OO] Outside Line Connection Assignment
[605]-[606] Outgoing Permitted Outside Line Assignment - Day /
Night
Feature ReferencesSection 3, Features
Outside Line Connection Assignment - Outgoing
Operation ReferencesDPT Features, Standard Telephone Features-User Manual
Outward Dialing - Line Access, AutomaticFeatures
3-93 
						

							LFeatures
Line Access, Direct
DescriptionAllows the proprietary telephone user to select an outside line by
pressing an idle CO button, which automatically establishes the
handsfree operation mode and allows the user to perform On-Hook
Dialing. The user need not press the SP-PHONE button,
MONITOR button nor 
lift the handset.
Conditionsl There are two types of CO buttons which can be programmed on an
extension: Single-CO button and Loop-CO button.
l Each extension is subject to System Programming items for outside
lines available to access.
Programming References
Feature References
Operation References-User Manual
Section 4, System Programming
[OOS] Flexible CO Button Assignment
[21 l] Dial Start Time
[400] Outside Line Connection Assignment
[605]-[606] Outgoing Permitted Outside Line Assignment - Day /
Night
St&ionProgramming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . User Manual
Flexible CO Button Assignment - Loop-CO (L-CO) Button,
Single-CO (S-CO) Button
Section 3, Features
Button, Loop-CO (L-CO)Outside Line Connection
Button, Single-CO (S-CO)Assignment 
- Outgoing
DPT Features
Outward Dialing - Line Access, Automatic / Line Access, Individual3-94Features 
						

							FeaturesL
Line Access, Individual
DescriptionAllows the proprietary telephone user one-button access to an
outside line without having to dial a line access code.
Conditionsl Each extension is subject to System Programming items for outside
lines available to access.
l This feature requires a Single-CO (S-CO) button assignment on a
proprietary telephone.
l The system waits for a programmed time before dialing after an outside
line is seized.
Programming References
Feature References
Operation References-User Manual
Section 4, System Programming
[005] Plexible CO Button Assignment
[211] Dial Start Time
[400] Outside Line Connection Assignment
[605]-[606] Outgoing Permitted Outside Line Assignment
- Day 1 Night
Station Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .User Manual
Plexible CO Button Assignment 
- Single-CO (S-CO) Button
Section 3, Features
Button, Single-CO (S-CO)Outside Line Connection
Assignment 
- Outgoing
DPT Features
Outward Dialing - Line Access, IndividualFeatures
3-95 
						

							LFeatures
Lint! Preference - Incoming (No Line / Prime Line / Ringing Line)
DescriptionA proprietary telephone user can select the method used to answer
incoming calls from the following three line preferences:
(1) No Line Preference
No line is selected when you go off-hook. You must select
a line to answer an incoming call.
(2) Prime Line Preference
You can assign a prime line beforehand and answer a call
on 
that line, when multiple calls are received
simultaneously.(3) Ringing Line Preference
Conditions
When you go off-hook, you can answer the call ringing at
your telephone.
l Setting a new line preference feature cancels the previous setting.
l If Prime Line Preference is selected and an incoming call arrives from a
line other than the prime line, it cannot be answered just by going 
off-
hook. The Prime Line should be assigned to the Single-CO button.
l If Ringing Line Preference is selected, going off-hook does not answer
a line programmed for “no ring” even though there is an incoming call.
Going off-hook during the delay time does not answer a line
programmed for “delayed ringing”.
l A standard telephone is always set to Ringing Line Preference and
cannot be changed.
Programming References
StationProgramming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UserManual
Preferred Line Assignment 
- Incoming
Feature ReferencesNone
Operation References Basic Operation-User Manual
Receiving Calls
3-96Features 
						

							3FeaturesL
Line Preference - Outgoing (Idle Line / No Line / Prime Line)
DescriptionA proprietary telephone user can select a desired outgoing line
preference to originate calls from the following three line
preferences:
(1) Idle Line Preference:
When you go off-hook, you are connected to an idle line.
An idle line is automatically selected from the pre-assigned
lines.(2) No Line Preference:
No line is selected when you go off-hook. You must select
a line to make a call.
(3) Prime Line Preference:
When you go off-hook, you are connected to the pre-
assigned line. Assign a line as your prime line beforehand.
Conditionsl Setting a new line preference feature cancels the previous setting.
l To set Prime Line Preference, one prime line is selected from intercom
or outside lines.
l The outside lines used by users must be connected by programming.
l To select Idle Line Preference, outside lines available for the user
should be programmed. Also outside lines available for Automatic
Line Access should be assigned.
l The user can override the Idle / Prime Line Preference temporarily to
select a specific line. To select it, press the 
desired line access button
(INTERCOM or CO button) before going off-hook or pressing the SP-
PHONE / MONITOR button; or if Full One-Touch Dialing is enabled,
press One-Touch Dialing, DSS, REDIAL, or SAVE button.
Programming References
Section 4, System Programming
[OOS] Flexible CO Button Assignment
[ 1031 Automatic Access Outside Line Assignment
[400] Outside Line Connection Assignment
[605]-[606] Outgoing Permitted Outside Line Assignment - Day / Night
Station Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .User Manual
Flexible CO Button Assignment 
- Loop-CO (L-CO) Button,
Single-CO (S-CO) Button
Preferred Line Assignment - Outgoing
Feature ReferencesSection 3, Features
Outside Line Connection Assignment - Outgoing
Operation References Basic Operation-User Manual
Making Calls
Features3-97 
						

							LFeatures
Live Call Screening (LCS)?
DescriptionAllows a digital proprietary telephone user to monitor their voice
mailbox while an incoming caller is leaving a message and, if
desired, intercept the call. The voice mailbox can be monitored in
one of two ways 
-Hands-free Mode or Private Mode.
Hands-free ModeThe voice mailbox is monitored through the built-in speaker
of the proprietary telephone.
Private Mode
The proprietary telephone emits an alert tone when callers are
connected to the voice mailbox. To monitor the call, the user
goes off hook with the handset or speakerphone.
Alert Tone
Conditions
IIIIIII
IIIIIII
III
I
IIITo intercept the call in either Hands-Free or Private mode, press 
;he
LCS button.
iiIII::IIA standard telephone, which is connected with a proprietary
telephone in parallel, can he also used to monitor a recording
message. Be sure that Live Call Screening on the connected
proprietary telephone has been activated.
This feature is useful when you are out with a portable handset of a
cordless telephone (standard telephone). The handset emits an alert
tone to let you know that a message is being recorded. To intercept
the call, flash the hookswitch.
l when the extension user is having a conversation, a call waiting tone is
sent. 
The user can put the existing call on hold before accessing LCS.
l A flexible CO and DSS button can be assigned as a Live Call Screening
button.
l To prevent unauthorized monitoring, a three-digit password must be set
by the LCS user. If the user forgets their password, it can be cleared by
the operator or manager.
l Each extension can be programmed to either close the mailbox or keep
recording the conversation after the call is intercepted.
3-98Featurest: Available when the Digital Super Hybrid System is connected to a Digital
Proprietary Telephone capable Panasonic Voice Processing System (one
that supports digital proprietary telephone integration; e.g. KX-TVSlOO). 
						

							FeaturesL
Programming References
Section 4, System Programming
[005] Flexible CO Button Assignment
[6 lo] Live Call Screening Recording Mode Assignment
StationProgramming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . YserManual
Flexible CO Button Assignment 
-Live Call Screening (LCS) Button
Live Call Screening (LCS) Cancel
Button
Live Call Screening Mode Set
Feature ReferencesNone
Operation References DPT Features-User Manual
Live Call Screening (LCS)Lockout
DescriptionIf one party in a conversation goes on-hook, they are both
disconnected from the speech path automatically. This feature
applies to extension and outside calls. A reorder tone is sent to the
off-hook party before it is disconnected.
ConditionsIn the case of a standard telephone, if nothing is dialed within a certain
period of time after the other party goes on-hook, a reorder tone is sent to
the standard telephone and then is disconnected from the speech path.
Programming References
No programming required.
Feature ReferencesNone
Operation ReferencesDPT Features, Standard Telephone Features-User Manual
Lockout
Features3-99 
						

							LFeatures
Log-In / Log-Out
DescriptionAssigns an extension to join (log-in) or leave (log-out) a hunting,
ring or UCD group. Extensions in log-out status will not receive
calls by Station Hunting but will receive other calls, unlike the
DND feature.
Conditionsl There should be at least one extension that is in log-in status.
l The lighting patterns and status of the Log-In/Log-Out button are
shown below.
lightingOutside Line Status
patternUCDStation Hunting
Red onLog-OutLog-Out
Red flashingLog-In (waiting calls)
-Off
Log-In (no calls)Log-In (no calls)
Programming References
Feature References
‘
Section 3, Features
Station Hunting
Ring CroupUniform Call Distribution (UCD)
Operation ReferencesDPT Features, Standard Telephone Features-User Manual
Log-In / Log-Out
Section 4, System Programming
[ 1001 Flexible Numbering, Log-in / log-out
Station Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .User Manual
Flexible CO Button Assignment - Log-In / Log-Out Button3-100Features