Panasonic Kx-Td308 Digital Super Hybrid System Installation Maintenence Manual

							FeaturesC
l Class of Service programming determines the extensions that are able to
perform this function.
l If an extension is limited by the program [502] “Extension-to-Outside
Line Call Duration Limit” according to its Class of Service, the
extension is unable to forward an outside call to an outside line.
l If a call between an extension and an outside party is established by this
feature, the duration of the call period can be restricted’depending on
the setting of the system timer. If a call between two outside parties is
established by this feature, the duration of the call is determined by
another system timer. An alarm tone is generated to both outside
parties 15 seconds before the time-out. The call is disconnected at the
time-out.
Programming References
Feature References
Section 3, Features
Limited Call Duration
Operation ReferencesDPT Features, Standard Telephone Features-User Manual
Call Forwarding - to Outside Line
Section 4, System Programming
[005] Flexible CO Button Assignment
[ 1001Flexible Numbering, Call forwarding / do not disturb
[205] Extension-to-Outside Line Call Duration Time
[206] Outside-to-Outside Line Call Duration Time
[502] Extension-to-Outside Line Call Duration Limit
[504] Call Forwarding to Outside Line
StationProgramming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UserManual
Flexible CO Button Assignment 
- FWD/DND ButtonFeatures
3-31 
						

							c3Features
Ca11 Hold - Intercom
DescriptionThis is used to place an intercom call on hold. The held call can be
retrieved by the user who held it or by any other extension.
Conditignsl Only one intercom call can be placed on hold at each telephone at one
time (up to ten calls in the system 
- Call Park). With a proprietary
telephone, outside calls and one intercom call can be placed on hold at
the same time. With a standard telephone, either one outside or
intercom call can be held.
l If a call on hold is not retrieved within a specific period of time, Hold
Recall is emitted.
l Music is sent to the party on hold, if available (Music on Hold).
Programming References
Section 4, System Programming
[ 1001 Flexible Numbering, Call hold
[200] Hold Recall Time
Feature ReferencesSection 3, Features
Call Park
Hold RecallMusic on Hold
Operation ReferencesDPT Features, Standard Telephone Features-User Manual
Call Hold
3-32Features 
						

							3FeaturesC
call Hold - Outside Line
DescriptionAllows the extension user to put an outside call on hold. The held
call can be retrieved by the user who held it or by any other
extension.
Conditionsl With a standard telephone, the user can hold only one call whether it is
an extension or outside call.
l Music is sent to the party on hold, if available (Music on Hold).
l If a call on hold is not retrieved in a specific period of time, Hold Recall
is emitted.
l If an outside party is placed on hold and not retrieved within 30
minutes, it is automatically disconnected.
Programming References
Section 4, System Programming
[ 1001 Flexible Numbering, Call hold
[200] Hold Recall TimeFeature References
Section 3, Features
Hold RecallMusic on Hold
Operation ReferencesDPT Features, Standard Telephone Features-User Manual
Call HoldFeatures
3-33 
						

							c3Features
Ca11 Hold, Exclusive - Intercom
DescriptionAllows the proprietary telephone user to prevent other extension
users from retrieving a held intercom call. Only the user who held
the call can retrieve it.
Conditionsl Only one intercom call can be placed on Call Hold or Exclusive Call
Hold at a time.
l If a call on hold is not retrieved in a specific period of time, Hold Recall
is emitted. After Hold Recall is emitted, the held call can be retrieved
from any extension.
l Music is sent to the party on hold, if available (Music on Hold).
Programming References
Section 4, System Programming
[200] Hold Recall Time
Feature ReferencesSection 3, Features
Hold Recall
Operation References DPT Features-User Manual
Call Hold, ExclusiveMusic on Hold3-34Features 
						

							Featuresc
Call Hold, Exclusive - Outside Line
Description
ConditikmsAllows 
the proprietary telephone user to prevent other extension
users from retrieving a held outside call. Only the user who held
the call can retrieve it.
l If a call on hold is not retrieved in a specific period of time, Hold Recall
is emitted. After Hold Recall is emitted, the held call can be retrieved
from any extension.
l If an outside party is placed on hold and not retrieved in 30 minutes, it
is automatically disconnected.
l Music is sent to the party on hold, if available (Music on Hold).
Programming References
Section 4, System Programming
[200] Hold Recall Time
Feature ReferencesSection 3, Features
Hold RecallMusic on Hold
Operation References DPT Features-User Manual
Call Hold, Exclusive
Ca11 Hold Retrieve - Intercom
DescriptionAllows the extension user to retrieve a call that has been placed on
hold by another extension.
ConditionsConfirmation tone is sent to the user when the hold is retrieved by the
feature number. Eliminating the tone is programmable.
Programming References
Section 4, System Programming
[ 1001Flexible Numbering, Call hold retrieve - intercom
[990] System Additional Information, Field (16)
Feature ReferencesSection 3, Features
Call Hold - Intercom
Operation ReferencesDPT Features, Standard Telephone Features-User Manual
Call Hold RetrieveFeatures
3-35 
						

							cFeatures
Ca11 Hold Retrieve - Outside Line
DescriptionAllows the extension user to retrieve a specified outside call that
has been placed on hold by another extension.
ConditiQnsA confirmation tone is sent to the user when the hold is retrieved by
entering the feature number. Eliminating the tone is programmable.
Programming References
Section 4, System Programming
[lOO] Flexible Numbering, Call hold retrieve - outside line
[990] System Additional Information, Field (16)
Feature ReferencesSection 3, Features
Call Hold - Outside Line
Operation ReferencesDPT Features, Standard Telephone Features-User Manual
Call Hold Retrieve
3-36Features 
						

							C
calling Party Control (CPC) Signal Detection
Description
ConditionsThe Calling Party Control (CPC) Signal is an on-hook indication
(disconnect signal) sent from the outside line when the telephone is
hung up at the other end. To maintain efficient utilization of
outside lines, the system monitors their state and when CPC Signal
is detected from a line, the system disconnects the line and alerts
the extension with a reorder tone.
l CPC Signal Detection is enabled or disabled on incoming and outgoing
outside calls by System Programming.
. Generally CPC Signal Detection works on incoming outside calls, and
does not work on outgoing outside calls (except once they are placed on
Call Hold, Exclusive Call Hold or Consultation Hold). In this case, if
the extension user remains off-hook after the completion of an outgoing
outside call, the system does not release all the switches used to
establish the connection. The connected outside line will continue to be
in use. To,prevent this, it is programmable to make CPC Signal
Detection work on outgoing outside calls. (Note: Some Central Offices
may send CPC-like signals during the dialing sequence and an attempt
to make a call may be terminated. If your CO does not send such
signals, it is recommended to make CPC Signal Detection work on
outgoing outside calls.)
l If your Central Office does not send CPC-like signals, it is effective to
limit the dialed numbers during a call by the program 
[991] “COS
Additional Information”; Class of Service to prevent unauthorized calls.
l If a CPC Signal is detected during a Conference call, the line is
disconnected and the remaining two parties resume the call.
l If a CPC Signal is detected during a call between a DISA caller and an
extension or an outside party, the line is disconnected.
Programming References
Section 4, System Programming
[405] CPC Signal Detection Incoming Set
[415] CPC Signal Detection Outgoing Set
[991] COS Additional Information, Field (1)
Feature ReferencesNone
Operation References Not applicable.Features
3-37 
						

							c3Features
Call Log, Incoming
DescriptionIf the display digital proprietary telephone (KX-T7230 or KX-
T7235) user cannot answer a call, the telephone automatically
records the caller’s information. The user can also record the
caller’s information manually, even after answering the call.
Moreover, the user can call back the caller by checking the call log.
This is available if a telephone receives incoming outside calls with
a Caller ID service. A maximum of 15 calls per telephone can be
logged.
The displayed information is as follows:
l The receiving outside line number and name
l The party’s phone number and name
l The date and time the call was made
l The sequence number and number of times calledConditions
l It is necessary to assign your area code first before you use the Caller
ID feature.
l The call is registered at the time DPT finishes ringing. If a call is
directed to multiple DPTs, the call is registered at the DPT that has the
smallest jack number of the ringing 
DPTs.However, if the telephone
which is connected to the smallest jack is not a DPT, the call is not
registered.
l Information is also recorded even if a transferred call (unscreened) is
not answered.
l When the call log is full (i.e. 15 calls are stored), the user can select to
overwrite the data, replacing the oldest call with the newest one at his 
/
her extension (Call Log, Incoming).
l The telephone user can lock the display of the unit so that incoming call
information is not shown on the display. The operator can cancel the
lock in case the user forgets the lock code,
l The system automatically modifies the incoming caller’s number in a
pre-programmed way for local or long distance calls. The modified
number will be recorded for calling back.

[ 
1251 “Area Code Assignment” : 201
[ 
1261 “Caller ID Modification for Local Call” :
delete 
- 3 digits, add - blank
[ 
1271 “Caller ID Modification for Long Distance Call” :
delete 
- 0 digit, add - 1
Caller’s numberRecorded
provided by COcaller’s number
Local call:20112345671234567 (modified by [ 1261)
Long distance call: 7 14987654317 149876543 (modified by [ 1271)
3-38Features 
						

							3Featuresc,:
Connection References
Section 2, Installation
2.4.2 4-SLT Extension Expansion Card / Caller ID/DISA/FAX Detection
Card Installation
Programming References
Feature References
Operation Reference-User Manual
Section 4, System Programming
[ 1001 Flexible Numbering, Call log, incoming / Call log lock, incoming
[ 1 lo]Caller ID Code Set
[ 11 l]Caller ID Name Set
[ 1251 Area Code Assignment
[ 1261 Caller ID Modification for Local Call
[ 
1271 Caller ID Modification for Long Distance Call
[406] Caller ID Assignment
[417] Outside Line Name Assignment
Section 3, Features
Caller ID
DPT Features
Call Log, Incoming
Call Log Lock, Incoming
Operator / Manager Service Features
Call Log Lock Control, IncomingFeatures
3-39 
						

							C
Call Park
DescriptionAllows the extension user to place a held call into a system parking
area.This releases the user from the parked call to perform other
operations. The parked call can be retrieved by any extension user.
Conditions
l The system contains ten parking areas, each of which has its own call
park number. Up to ten calls can be parked at the same time in the
system.
l If a parked call is not retrieved in a specific period of time, Call Park
Recall occurs. If a parked call is an outside call, it is possible to select
whether Call Park Recall will go to the initiating extension or to
Operator 1 by System Programming. If a parked call is an intercom
call, Call Park Recall will return to the initiating extension.
l If a parked call is not retrieved in 30 minutes, it is automatically
disconnected.
l A confirmation tone is sent to the user when the parked call is retrieved.
Eliminating the tone is programmable.
Programming References
Section 4, System Programming
[ 1001Flexible Numbering, Call park / call park retrieve
[219] Call Park Recall Time
[990] System Additional Information, Fields (1 l), (16)
Feature ReferencesNone
Operation ReferencesDPT Features, Standard Telephone Features-User Manual
Call Park
3-40Features