Panasonic Kx-Td308 Digital Super Hybrid System Installation Maintenence Manual

							402 4~Outside Line Programming
Dial Mode Selection (contd.)
Conditionsl To assign all lines to one selection, press the Jc key in step 3. In this
case, the display shows the contents programmed for outside line 1.
l If DTMF is assigned, set the DTMF time of the line in program [404]
“DTMF lime”.
l If pulse or call blocking is assigned, set the pulse speed of the line in
program 
[403] “Pulse Speed Selection”, and set the pulse break ratio
and inter-digit pause in program 
[990] “System Additional Information,
Field 
(17)” and in “Field (2 1 )“, if necessary.
Feature ReferencesSection 3, Features
Dial ‘Ijpe Selection
4-96System Programming
. 
						

							460Outside Line Programming
Pulse Speed Selection
403
Selection
DefaultAll outside lines 
- 10 pps
Programming1.Enter 403.
DescriptionAn outside line set for pulse or call blocking mode in program
[402] “Dial Mode Selection” can have two pulse rates, 10 pps (low)
and 20 pps (high). This program sets the pulse speed for each
outside line set to pulse or call blocking mode.
l Outside line (CO) number: 1 through 3, * ( * =all outside lines). 
lOpps/2Opps
Display: 403 PULSE SPEED
2.Press NEXT.
3.
4.
5.
6.
Display: CO Line NO?+
Enter an outside line number.
To enter outside line number 1, you can also press NEXT.
Display example: CO1:lOpps
Keep pressing SELECT until the desired selection is
displayed.
Press 
STORE.
To program another outside line, press NEXT or PREV, or
SELECT and the desired outside line number.
7.Repeat steps 4 through 6.
8.Press END.
Conditionsl To assign all outside lines to one selection, press the * key in step 3.
In 
this case, the display shows the contents programmed for outside line
1.
l Tbe pulse speed required is determined by the CO or PBX line.
l Program [990] “System Additional Information, Field (17) and Field
(21)” are used to select a pulse break ratio and inter-digit pause, if
needed.
Feature ReferencesSection 3, Features
Dial Type SelectionSystem Programming
.
4-97 
						

							Outside Line ProgrammingDTMF Time
DescriptionAn outside line set to DTMF mode in program [402] “Dial Mode
Selection” can have two settings. This program sets the duration of
the DTMF signals sent to an outside line to DTMF mode.
Selectionl Outside line (CO) number: 1 through 3, * ( * =all outside lines)
l Time (milliseconds): 80 / 160
DefaultAll outside lines - 80 ms
Programming1.Enter 404.
Display: 404 DTMF TIME
2.Press NEXT.
Display: CO Line NO?+
3.Enter an outside line number.
To enter outside line number 1, you can also press NEXT.
Display example: COl: 80msec
4.Keep pressing SELECT until the desired selection is
displayed.
5.Press STORE.
6.To program another outside line, press NEXT or PREV, or
SELECT and the desired outside line number.
7.Repeat steps 4 through 6.
8.Press END.
Conditionsl To assign all outside lines to one selection, press the * key in step 3.
In this case, the display shows the contents programmed for outside line
1.
l The DTMP time required is determined by the outside line or PBX line.
Feature ReferencesSection 3, Features
Dial Type Selection
4-98System Programming
. 
						

							46lOutside Line Programming405
CPC Signal Detection Incoming Set
DescriptionAssigns the expected minimum duration of the CPC Signal on
incoming outside calls. If this is programmed, the system
disconnects the line when the CPC Signal is detected.
Selectionl Outside line (CO) number: 1 through 3, * ( * =all outside lines)
l Time (milliseconds): Disable (no detection) / 100 / 200 / 300 /
400/500/600
DefaultAll outside lines - 400 ms
Programming1.Enter 405.Display: 405 CPC INCOMING
2.Press NEXT.Display: CO Line NO?+
3.Enter an outside line number.
To enter outside line number 1, you can also press NEXT.Display 
example: C01:400msec
4.Keep pressing SELECT until the desired time is displayed.
5.Press STORE.
,6.To program another outside line, press NEXT or PREV, or
SELECT and the desired outside line number.
7.Repeat steps 4 through 6.
8.Press END.
Conditionsl To assign all outside lines to one selection, press the Jt key in step 3.
In this case, the display shows the contents prograquned for outside line
1.
l You may disable CPC Signal Detection for an outside line.
l Program [415] “CPC Signal Detection Outgoing Set” is used to
program CPC Signal Detection for outgoing outside calls.
Feature ReferencesSection 3, Features
Calling Party Control (CPC) Signal Detection
Direct Inward System Access (DISA)
System Programming4-99 
						

							406 46Outside Line Programming
Caller ID Assignment
DescriptionEnables the Caller ID feature for the outside lines to which a Caller
ID Service is offered by a Central Office by contract.
Selectionl Outside line (CO) number: 1 through 3, * ( * =all outside lines)
l Enable / Disable
DefaultAll outside lines - Disable
Programming1.
2.
3.
4.
5.
6.
7.Repeat steps 4 through 6.
8.Press END.
Conditions
Enter 406.
Display: 406 CALLER ID CO
Press NEXT.
Display: CO Line NO?+
Enter an outside line number.
To enter outside line number 1, you can also press NEXT.
Display example: CO1:Disable
Keep pressing SELECT until the desired selection is
displayed.
Press STORE.
To program another outside line, press 
NEXT or PREV, or
SELECT and the desired outside line number.
l To assign all outside lines to one selection, press the * key in step 3.
In this case, the display shows the contents programmed for outside line
1.
l The following programs are used to program Caller ID feature: [ 1 lo]
“Caller ID Cede Set” and [ 11 l] “Caller ID Name Set”.
Feature ReferencesSection 3, Features
Caller ID
4-100System Programming
. 
						

							46lOutside Line Programming 407-408
DIL I:1 Extension- Day /Night
DescriptionThe Direct In Lines (DIL) 1: 1 feature allows incoming outside calls
to be directed to a specific extension. When an outside line is
assigned as DIL 1: 1, it is necessary to assign the destination. These
programs specify the extension number for day or night mode.
Selection
DefaultAll outside lines 
- Disable - Day / Night
Programming1.Enter a program address (407 for day or 408 for night).Display example: 407 DIL 
1:l DAY
Conditionsl Outside line (CO) number: 1 through 3, 
* ( * =all outside lines)
l Extension number: 2 through 4 digits / Disable (no DIL 1: 1)
2.Press NEXT.
3.
4.
5.
6.Display: CO Line NO?+
Enter an outside line number.
To enter outside line number 1, you can also press NEXT.Display example: 
COl:Disable
Enter an extension number.
To change the current entry, press CLEAR and enter the new number.
To disable. DIL 1: 
1, press CLEAR.
Press STORE.
To program another outside line, press NEXT or PREV, or
SELECT and the desired outside line number.
7.Repeat steps 4 through 6.
8.Press END.
l To assign all outside lines to one selection, press the * key in step 3.
In this case, the display shows the contents programmed for outside line
.1.
l You set the extension numbers in program [003] “Extension Number
Set” or floating numbers of pager and DISA message in program [8 131
“Floating Number Assignment”.
l If an outside line is also programmed for DIL 1 :N in programs
[603]-[604] “DIL 1 :N Extension and Delayed Ringing - Day / Night”,
it is regarded as a DIL 1: 1 line.
Feature ReferencesSection 3, Features
Direct In Lines (DIL)Night Service
Direct Inward System Access (DISA)System Programming4-101 
* 
						

							4091410 4*tFiOutsidti Line Programming
Intercept Extension- Day /Night
DescriptionIntercept Routing provides an automatic redirection of calls which
cannot or have not been answered. These programs set the
destination in both day and night modes for each outside line.
Selectionl Outside line (CO) number: 1 through 3, * ( x =aIl outside lines)
l Extension number: 2 through 4 digits / Disable (no Intercept
Routing)
DefaultAI1 outside lines - Disable - Day / Night
Programming1.
2.
3.
4.
5.
6.Display: CO Line NO?+
Enter the outside line number.
To enter outside line number 1, you can also press NEXT.Display example: 
CO1:Disable
Enter an extension number.
To change the current entry, press CLEAR and enter the new number.
To disable Intercept Routing, press CLEAR.
Press STORE.
To program another outside line, press NEXT or PREV, or
SELECT and the desired outside line number.
7.Repeat steps 4 through 6.
8.Press END.
Enter a program address (409 for day or 410 for night).Display example: 409 INTERCEP DAY
Press NEXT.
Conditionsl You set the extension numbers in program [003] “Extension Number
Set” or floating numbers of pager and DISA message in program 
[8 131
“Floating Number Assignment”.
l To assign all outside lines to one selection, press the * key in step 3.
In this case, the display shows the contents programmed for outside line
1.
l Program [401] ‘Outside Line Group Assignment” is used to assign each
outside line to an outside line group.Feature References Section 3, Features
Intercept Routing
4-102System Programming
. 
						

							46lOutside Line Programming411
Host PBX Access Codes
DescriptionAssigns Host PBX or Centrex access codes. If the.system is
installed behind a host PBX or a 
Centrex system, an access code is
required to make an outside 
/ Centrex call or to access Centrex
features. Up to four codes can be stored for an outside line
assigned to the line.
Selection
Default
Programmingl Outside line (CO) number: 1 through 3, * ( * =all outside lines)
l Access code: 1 or 2 digits, four different entries (max.)
All outside lines - Not stored
1.
2.
3.
4.
5.
6.
7.
8.
Repeat steps 4 through 7.
9.
Enter 411.
Display: 411 HOST PBX #S
Press NEXT.
Display: CO Line NO?+
Enter an outside line number.
To enter outside line number 1, you can also press NEXT.Display example: 
COl: , , ,
Enter an access code.
To delete the current entry, press CLEAR.
To change the current entry, press CLEAR and enter the new access code.Display example: 
COl:Ol, , ,
To enter more access codes for the same outside line, press
e and enter the access codes until all the required entries
are completed.
Display example: CO1:01,08,10,22
Press STORE.
To program another outside line, press NEXT or PREV, or
SELECT and the desired outside line number.
Press END.
Systerri Programming4-103 * 
						

							41146lOutside Line Programming
Host PBX Access Codes (contd.)
Conditionsl This program is only required if a host PBX or Centrex line is
connected to the system.
l There is a maximum of four access codes per outside line. Each code
has one or two digits, consisting of 0 through 9, and * .
l If conflicting access codes (such as 8 and 81) are stored for the same
outside line, the l-digit code (8) only will be in effect.
l When the programmed codes are dialed, Automatic Pause Insertion and
Toll Restriction are applied to the calls. The programmed pause time
(in program 
[412] “Pause Time”) is automatically inserted after the
access code.
l To assign all outside lines to one selection, press the Jc key in step 3.
In this case, the display shows the contents programmed for outside line
1.
Feature ReferencesSection 3, Features
External Feature Access
Host PBX AccessPause Insertion, Automatic
4-104System Programming
. 
						

							46lOutside Line Programming412
Pause Time
DescriptionAssigns the length of the pause time. The programmed pause time
is automatically inserted after a line access code or a host PBX
access code programmed in 
[41 l] “Host PBX Access Codes” or
manually inserted if the 
PAUSE button is pressed by the user.
Selectionl Outside line (CO) number: 1 through 3, * ( * =all outside lines)
l Time (seconds): 1.5 / 2.5 / 3.5 / 4.5
DefaultAll outside lines - 1.5 s
Programming1.
2.
3.
4.
5.
6.
7.
8.
Enter 412.
Display: 412 PAUSE TIME
Press NEXT.
Display: CO Line NO?-+
Enter an outside line number.
To enter outside line number 1, you can also press NEXT.Display example: 
CO1:1.5sec
Keep pressing SELECT until the desired time is displayed.
Press STORE.
To program another outside line, press NEXT or PREV, or
SELECT and the desired outside line number.
Repeat steps 4 through 6.
Press END.
Conditionsl To assign all outside lines to one selection, press the * key in step 3.
In this case, the display shows the contents programmed for outside line
1.
Feature ReferencesSection 3, Features
Host PBX AccessPause Insertion, Automatic
.
System Programming4-105