Oce ColorWave 300 User Manual

							Description / Function
Component
Guides the original over the scanner to the
front.
original guide
-
When to do The 
copy and scan quality can decrease if
■ the
 transparent contact 
plates (8) are dirty or static.
■ The
 
original support rollers (5) are dirty and you use transparent originals.
In
 that 
case you must clean the scanner to ensure top quality output.
How
 to clean the scanner 1. Use 
both hands to push up the left and right scanner open levers (4) to fully open the
scanner top 
cover (3). Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer 291Clean the scanner
Downloaded From ManualsPrinter.com Manuals 
						

							A locking mechanism prevents the scanner top cover from closing.
Caution:
To clean the scanner use the soft lint-free Masslin towels from the scanner cleaning kit.
2. Use 
a Masslin towel that has been moistened with water and firmly wrung out to clean
the following parts of the scanner. Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer292Clean the scanner
Downloaded From ManualsPrinter.com Manuals     
						

							■
the original support rollers (5)
Rotate
 
the rollers to clean them.
■ the transparent contact 
plates (8)
Wipe
 
off any soiled areas. 3. Wipe 
all the cleaned parts once again using a dry Masslin towel.
Warning:
Take care not to get your fingers caught in the scanner top cover.
4.
Press the scanner top 
cover down gently with both hands to close it.
Note:
Check that the left and right scanner open levers are locked into position. Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer 293Clean the scanner
Downloaded From ManualsPrinter.com Manuals   
						

							Calibrate the scanner
Introduction
You can calibrate the scanner when you are not satisfied with the copy or scan quality.
Use
 
the calibration wizard on the printer user panel to calibrate the scanner.
Before
 you begin Clean 
the scanner before you start the calibration procedure. Dirty parts of the scanner
causes
 a decreased copy and scan quality. (See ‘Calibrate the scanner’  
on page 294 ).
Caution:
Handle the calibration sheet with care.
Caution:
Do not touch the black area of the calibration sheet with your fingers.
Caution:
Before you use the calibration sheet wipe off any dust from the calibration sheet.
How to calibrate the scanner
1.From 
the 'HOME' screen select the 'System' tab.
2. Select
 the 'Setup' 
tab.
3. Use 
the scroll wheel to go to the 'Scanner calibration'('Calibrate the scanner') wizard. 4. Open this section with 
the confirmation button.
Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer294Calibrate the scanner
Downloaded From ManualsPrinter.com Manuals 
						

							5.
Insert the scanner calibration sheet¹ as instructed in the wizard.
6. Press
 the start 
button to start the scanner calibration.
The
 
message 'Calibrating, please wait... do not open the scanner.' appears.
Note:
'Calibrating the scanner takes between 5 to 10 minutes.'
Note:
¹ The scanner calibration sheet code number is 97002634. Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer 295Calibrate the scanner
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 7 - Maintain the Océ ColorWave 300 multifunction printer296Calibrate the scanner
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 8
System 
messages and so-
lutions
Downloaded From ManualsPrinter.com Manuals 
						

							The printer
Overview
Definition
This table gives an overview of the possible error messages and system messages of the
printer
 and refers to 
the possible solution. #
Description / solution
Error message / System mes-
sage
The media required for the job is not available on
the printer.
See

 
‘Replace / Install the media’  on page 272
'Required
 
media not available'
The end of the roll of media is reached while you
print
See 
‘Replace / Install the media’  on page 272
'Roll
 
empty'
A door 
or cover is open, although you are not in
a wizard
See
  
‘Cover or door opened’  on page 300
'Close
 maintenance door' 
/
'Close top 
cover.'
A media jam 
occurred
See 
‘Remove jammed media’  on page 302
'Remove
 media'
Excessive
  temperature or humidity.
See

  ‘Temperature or humidity out of range’  on page
304
'Temperature out of range'
/'Humidity
 out 
of range'
The  
carriage is away from its home position too
long
See
  ‘Carriage away from home position too long’ on
page 305
'Warning

 Carriage away from
home

 
position too long'
Printhead
 error messages The 
table below gives on overview of the printhead-related error codes.
Chapter 8
 - System messages and solutions298Overview
Downloaded From ManualsPrinter.com Manuals 
						

							#
Customer action
Description
Error
code
Replace the printhead by using the
wizard.
Note:
Never re-insert a printhead
that
 has caused this problem. Excessive leakage current detect-
ed for head [1…9]
Printhead

 failing
Replace

 
printed [1…9]
4501
 -
4509
Printhead is probably not 
placed
correctly. Remove and re-insert the
printhead

 at 
the original position.
Note:
If the problem persists you
must replace the printhead. Head 
defective during printing
4551 -
4559
You can 
ignore this problem by
pushing
 the 'OK' 
button.
Note:
If the problem re-occurs after
a short 
time you must re-
place
 
the printhead. Head 
too hot during printing
4571 -
4579
Replace 
the printhead by using the
wizard.
Head
 [1….9] keeps heating
4581 -
4589
Service warning only. No 
customer
intervention needed.
WOM

 memory failure for head
[

 1……9]
4951 -
4959
Continue printing until the message
'Replace 
printhead' displays on the
user
 panel.
Then
  replace the printhead by using
the wizard.
Heating

 of head [1……9] failed 4961
 -
4969 Chapter 8
 - System messages and solutions 299Overview
Downloaded From ManualsPrinter.com Manuals 
						

							Cover or door opened
Cover or door opened
When you open a cover accessing the wizard, the system produces a double warning signal.
When you open a door or cover during printing, the printer stops. A message on the
printer
 user panel tells you 
to close the cover. Close the cover to continue. Examples:
Chapter 8
 - System messages and solutions300Cover or door opened
Downloaded From ManualsPrinter.com Manuals