Oce ColorWave 300 User Manual

							Caution:
Always store printheads near the printer or allow the printheads to adjust to the printers
environmental conditions before you 
insert them in to printer.How to remove a printhead
1.From

 
the'HOME' screen select the 'System' tab.
2. Select
 the 'Setup' 
tab.
3. Use 
the scroll wheel to go to the 'Printheads'('Replace printheads') wizard. 4.
Open this section with 
the confirmation button.
5. An introduction screen displays the message 'Use this wizard to replace printheads. A roll
is needed for calibration.' 6.
Press the key for 'Next >'.
The

 
screen displays the message 'Select roll to use'.
The system does a calibration at the end of the wizard. You can only calibrate on the de-
fined media types 
‘Use the 'Print quality' wizard’  on page 267. When calibration is not
possible
 with 
the media available on the printer, the system asks you to load the correct
media.
 When calibration is possible with 
one of the rolls, the system automatically uses
the
 correct media roll. When calibration is possible with 
both rolls, use the scroll wheel
to
 
select the media roll and press the confirmation button to select the roll.
7. Press the key for 'Next >'.
Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer 281Replace a
 defective printhead
Downloaded From ManualsPrinter.com Manuals 
						

							The screen displays the message 'Carriage moving into position...' while the carriage
moves
 
to the center.
The
 
screen displays 'Open printhead door.'
8. 'Open
 printhead door.'. The screen displays the message 'Replace printheads' and the print head(s) that you must
replace. Find 
the correct printhead number on the printhead carriage.
9.
Press the front 
of the printhead cover to unlock the cover. Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer282Replace a
 defective printhead
Downloaded From ManualsPrinter.com Manuals 
						

							10.
Open the printhead cover. 11.
Pull out the printhead and remove it. How to place a printhead
1. Remove the protective tape from 
the new printhead.
Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer 283Replace a
 defective printhead
Downloaded From ManualsPrinter.com Manuals 
						

							Hold the printhead at to top.
Note:
Do not touch the contact and nozzle areas of the printhead after you remove the protective
tape.
Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer284Replace a
 defective printhead
Downloaded From ManualsPrinter.com Manuals 
						

							2.
Place the new printhead in the printhead holder.
The
 
printhead only fits in one way.
3. Close the printhead cover.
4. After

 you 
replaced the defective printhead, press the softkey for 'Next >'
5. The
 screen displays the message 'Make sure that all printhead covers are properly closed.' Press the key for 'Done'.
The

 
screen displays the message 'Close printhead door.'
6. 'Close
 printhead door.'
7. The

 
screen displays 'Preparing calibration...'.
The
 
calibration process takes several minutes.
You
 can 
stop the calibration process at any time. Press the key for 'Cancel' to stop the
calibration
 process.
Note:
If you cancel the calibration, the printer restarts the calibration process when a new print
job starts.
Note:
If the printer rejects the new printhead during the 'Replace printheads' procedure, remove
the printhead, clean 
the contact area with a lintfree cloth and re-insert the print head.
Note:
Also check the maintenance cassette after you replaced a printhead.  ‘Replace the mainte-
nance cassette’  on page 286 Check if all wipers are present and clean. Excessive ink remains
on the wipers 
can damage the printheads. Wipe the wiper blades with a moist cloth to
increase
 the lifetime of the printheads. Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer 285Replace a
 defective printhead
Downloaded From ManualsPrinter.com Manuals 
						

							Replace the maintenance cassette
Introduction
The maintenance cassette wipes the printheads and caps the printhead nozzles.
During
 the print process, the printhead carriage regularly 
moves to the right-hand side
of the printer to 
spit some ink droplets into the maintenance cassette. These actions are
necessary
 to 
keep the printheads in optimal condition.
After
 about 5000 m 2
of
 output (the exact value depends on the print modes you use) the
printer indicates that 
you must replace the maintenance cassette.
When
 to do Replace the maintenance cassette when user panel displays the message 'Replace mainte-
nance tray'. The 
print quality can deteriorate. Replace the cassette as soon as possible.
Caution:
Do not remove the maintenance cassette when you are not in the wizard. You can seri-
ously damage the printheads. When you open the maintenance door outside the wizard,
an error message prompts 
you to close the door. How to remove the maintenance cassette
1.From 
the'HOME' screen select the 'System' tab.
2. Select
 the 'Setup' 
tab.
3. Use the scroll wheel to go to the 'Maintenance tray'('Replace maintenance tray') section.
4. Open this section with 
the confirmation button.
5. An introduction screen displays the message 'Use this wizard to replace the maintenance
tray.' 6. Press the 'Next >' 
key.
Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer286Replace the maintenance cassette
Downloaded From ManualsPrinter.com Manuals 
						

							The screen displays the message 'Carriage moving to center position...' while the carriage
moves to the center.
Then,
 
the screen displays the message 'Open maintenance door.'
7. Open
 the door 
to the maintenance cassette.
The
 
screen displays the message 'Remove tray.'
8. Press
 the green grip to 
the left to release the cover that gives access to the maintenance
cassette. 9.
Pull 
out the maintenance cassette.
Note:
Always store the old maintenance cassette in a horizontal position to prevent the spilling
of ink. Be careful with 
the ink on the maintenance cassette. Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer 287Replace the maintenance cassette
Downloaded From ManualsPrinter.com Manuals 
						

							Note:
The packing of the new maintenance cassette also includes a plastic zip lock waste bag.
Use 
this bag to dispose of the old maintenance cassette. How to place the maintenance cassette
1.The 
screen displays the message'Place new maintenance tray.'
2. Slide
 
the new maintenance cassette into the cassette holder.
3. Close
 the cover of the maintenance cassette .
 The cover locks automatically.
4. 'Close
 maintenance door.'
5. The

 
screen displays the message 'Is the tray you placed used or new?'
Caution:
Make sure that you select the correct option. Never select 'New' for a used cassette. This
can 
seriously damage your printheads. 6.
Press the key for 'Used' 
or 'New'.
Select
 'Used' 
if you inserted a cassette that was used before. The end-of-life counter is
not 
reset to zero.
Select 'New' 
if you inserted a cassette that was not used before. The end-of-life counter
is reset to 
zero.
7. The 
screen displays the message 'Carriage moving to home position...'.
8. The 
maintenance cassette is replaced.
Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer288Replace the maintenance cassette
Downloaded From ManualsPrinter.com Manuals 
						

							Remote consumables reading
Introduction
An administrator can remotely read out the Océ ColorWave 300consumables settings
for administrative purposes.
The

 
following Océ ColorWave 300 information is available:
■ Basic
 settings of the system
■ Print

 head information for each 
color
■ Ink 
tank information for each color
■ Maintenance Cassette usage.
Read

 the information 1. Start a Web 
browser (e.g. Internet Explorer) on your workstation.
2. Fill 
in the URL: http:///servlet/ALGetResourceCounters?identification=1
Fill 
in the correct hostname or IP address of your system.
3. You will 
get an overview of the consumables information.
Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer 289Remote consumables reading
Downloaded From ManualsPrinter.com Manuals 
						

							Maintain the scanner
Clean the scanner
Introduction
#
Description / Function
Component
Use this ruler to measure the original.
original
 size ruler
1
A set of rollers used 
to transport the origi-
nal.
original
 feed rollers
2
Top cover of the scanner.
scanner

 top cover
3
Lever to open the top cover of the scanner.
scanner open 
levers
4
A set of rollers to 
guide the original.
original
 support rollers
5
A set of rollers in the top cover to guide the
original.
scanner top 
cover rollers
6
Sensors to 
detect the original.
original
 sensors
7
Cover of the image sensors.
transparent

 contact plates
8
Use 
this table if you feed the original into
the scanner.
original

 
feeding table 9
Chapter 7
 - Maintain the Océ ColorWave 300 multifunction printer290Clean the scanner
Downloaded From ManualsPrinter.com Manuals912
3
56784