Home > Nitsuko > Communications System > Nitsuko Digital System Feature And Terminal Programming Manual

Nitsuko Digital System Feature And Terminal Programming Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Nitsuko Digital System Feature And Terminal Programming Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 57 Nitsuko manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 708
    							CP- SINGLE RING OPX (BY2:7)
    Description
    Use this option to enable (0) or disable (1) Distinctive Ringing for ports with circuit types 05 and 51 (OPX and
    ASI extensions). If enabled (0), trunk calls have two short rings (repeated) followed by a pause.  Intercom calls
    have a single one second ring followed by a pause.  If disabled (1), Intercom and trunk calls have a single one
    second ring followed by a pause.
    In  
    >AUX Y2.1/Base Y5.1, use this option to control the types of calls Voice Mail Personal Answering Machine
    Emulation answers.  If enabled (1), Personal Answering Machine Emulation answers only trunk calls.  Intercom
    calls to the extension go through normally.  If disabled (0), Personal Answering Machine Emulation answers all
    calls (Intercom and trunk).  For more information, refer to the Voice Mail Compatibility feature.
    Conditions
    None
    Default Value
    Distinctive Ringing enabled (0).
    Feature Reference
    Distinctive Ringing, Tones and Flash Patterns
    Instructions
    To enter data on the PRF:
    1. On Table 2 for BY2:7, enter 0 allow Distinctive Ringing at circuit type 05/51 ports.  Enter 1 to prevent
    Distinctive Ringing.
    OR
    On Table 2 for BY3:6, enter 0 to have Personal Answering Machine Emulation answer all calls to an 
    extension.  Enter 1 to have Personal Answering Machine Emulation answer only trunk calls.
    To enter data at the programming terminal:
    1. Type CP.  You see: COS # 00: 00010000 00000-0 00000001 00000000
    2. Enter data for each COS you want to program.
    C- CLASS OF SERVICE
    CP- SINGLE RING OPX (BY2:7)
    324   PROGRAMMING N1870SWG04   Issue 1-0 
    						
    							CP- INHIBIT FLASH FOR SINGLE LINE TELEPHONES (BY2:6)
    Description
    Use this option to enable (0) or disable (1) Flash for ESL sets with this COS.  If enabled, ESL users can press
    and release the hookswitch to Flash a trunk.
    Note:
    If you are using BY2:6 to assign an ACD supervisor keyset, go to CP- ACD Supervisor Keyset (BY2:6) on the
    next page.
    Conditions
    None
    Default Value
    Flash allowed at ESL sets (0).
    Feature Reference
    Flash
    Instructions
    To enter data on the PRF:
    1. On Table 2 for BY2:6, enter 0 allow Flash at ESL sets.  Enter 1 to prevent Flash at ESL sets.
    To enter data at the programming terminal:
    1. Type CP.  You see: COS # 00: 00010000 00000-0 00000001 00000000
    2. Enter data for each COS you want to program.
    C- CLASS OF SERVICE
    CP- INHIBIT FLASH FOR SINGLE LINE TELEPHONES (BY2:6)
    N1870SWG04   Issue 1-0 PROGRAMMING   325 
    						
    							CP- ACD SUPERVISOR KEYSET (BY2:6)
    Description
    Use this option to assign extensions with this COS as ACD supervisor keysets.  This option only identifies the
    extension as a supervisor.  It does not assign the keyset to an ACD group (see Related Programming below).  If
    enabled (1), extension is an ACD supervisor.  If disabled (0), extension is not a supervisor.
    Conditions 
    None
    Default Value
    ACD supervisor not assigned (0).
    Feature Reference
    Automatic Call Distribution
    Instructions
    To enter data on the PRF:
    1. On Table 2 for BY2:6, enter 0 if the keyset is not an ACD group supervisor.  Enter 1 if the keyset is an
    ACD supervisor.
    To enter data at the programming terminal:
    1. Type CP.  You see: COS # 00: 00010000 00000-0 00000001 00000000
    2. Enter data for each COS you want to program.
    C- CLASS OF SERVICE
    CP- ACD SUPERVISOR KEYSET (BY2:6)
    326   PROGRAMMING N1870SWG04   Issue 1-0 
    						
    							CP- ALLOW SILENT MONITOR (BY2:5)
    Description
    Use this option to allow (1) or prevent (0) Silent with this COS from initiating Silent Monitor.
    Conditions 
    None
    Default Value
    Silent Monitor not allowed (0).
    Feature Reference
    Silent Monitor
    Instructions
    To enter data on the PRF:
    1. On Table 2 for BY2:5, enter 0 to prevent extensions from initiating Silent Monitor.  Enter 1 to allow ex-
    tensions to initiate Silent Monitor.
    To enter data at the programming terminal:
    1. Type CP.  You see: COS # 00: 00010000 00000-0 00000001 00000000
    2. Enter data for each COS you want to program.
    C- CLASS OF SERVICE
    CP- ALLOW SILENT MONITOR (BY2:5)
    N1870SWG04   Issue 1-0 PROGRAMMING   327 
    						
    							CP- INHIBIT ACCESS TO PAGE ZONE 3 (BY2:4)
    Description
    Use this option to allow (0) or prevent (1) extensions with this COS from broadcasting announcements into Paging
    zone 3.  This option also applies to DISA trunks.
    Conditions 
    None
    Default Value
    Access to Page Zone 3 allowed (0).
    Feature Reference
    Paging
    Tenant Service
    Instructions
    To enter data on the PRF:
    1. On Table 2 for BY2:4, enter 0 to allow extensions Paging into zone 3.  Enter 1 to restrict extensions from
    Paging into zone 3.
    To enter data at the programming terminal:
    1. Type CP.  You see: COS # 00: 00010000 00000-0 00000001 00000000
    2. Enter data for each COS you want to program.
    C- CLASS OF SERVICE
    CP- INHIBIT ACCESS TO PAGE ZONE 3 (BY2:4)
    328   PROGRAMMING N1870SWG04   Issue 1-0 
    						
    							CP- INHIBIT ACCESS TO PAGE ZONE 2 (BY2:3)
    Description
    Use this option to allow (0) or prevent (1) extensions with this COS from broadcasting announcements into Pag-
    ing zone 2.  This option also applies to DISA trunks.
    Conditions 
    None
    Default Value
    Access to Paging zone 2 allowed.
    Feature Reference
    Paging
    Tenant Service
    Instructions
    To enter data on the PRF:
    1. On Table 2 for BY2:3, enter 0 to allow extensions Paging into zone 2.  Enter 1 to restrict extensions from
    Paging into zone 2.
    To enter data at the programming terminal:
    1. Type CP.  You see: COS # 00: 00010000 00000-0 00000001 00000000
    2. Enter data for each COS you want to program.
    C- CLASS OF SERVICE
    CP- INHIBIT ACCESS TO PAGE ZONE 2 (BY2:3)
    N1870SWG04   Issue 1-0 PROGRAMMING   329 
    						
    							CP- INHIBIT ACCESS TO PAGE ZONE 1 (BY2:2)
    Description
    Use this option to allow (0) or prevent (1) extensions with this COS from broadcasting announcements into Paging
    zone 1.  This option also applies to DISA trunks. 
    Conditions 
    None
    Default Value
    Access to Paging zone 1 allowed.
    Feature Reference
    Paging
    Tenant Service
    CP- INHIBIT ACCESS TO PAGE ZONE 1 (BY2:2)
    Instructions
    To enter data on the PRF:
    1. On Table 2 for BY2:2, enter 0 to allow extensions Paging into zone 1.  Enter 1 to restrict extensions from
    Paging into zone 1.
    To enter data at the programming terminal:
    1. Type CP.  You see: COS # 00: 00010000 00000-0 00000001 00000000
    2. Enter data for each COS you want to program.
    C- CLASS OF SERVICE
    CP- INHIBIT ACCESS TO PAGE ZONE 1 (BY2:2)
    330   PROGRAMMING N1870SWG04   Issue 1-0 
    						
    							CP- INHIBIT ACCESS TO ALL CALL PAGING (BY2:1)
    Description
    Use this option to allow (0) or prevent (1) extensions with this COS from broadcasting All Call Paging an-
    nouncements.  This option also applies to DISA trunks.
    Conditions 
    None
    Default Value
    Access to All Call Paging allowed.
    Feature Reference
    Paging
    Tenant Service
    Instructions
    To enter data on the PRF:
    1. On Table 2 for BY2:1, enter 0 to allow extensions All Call Paging.  Enter 1 to restrict extensions from
    All Call Paging.
    To enter data at the programming terminal:
    1. Type CP.  You see: COS # 00: 00010000 00000-0 00000001 00000000
    2. Enter data for each COS you want to program.
    C- CLASS OF SERVICE
    CP- INHIBIT ACCESS TO ALL CALL PAGING (BY2:1)
    N1870SWG04   Issue 1-0 PROGRAMMING   331 
    						
    							CP- DIRECT TRUNK ACCESS AND TRUNK CAMP-ON (BY2:0)
    Description
    Use this option to enable (1) or disable (0) Direct Trunk Access for extensions with this COS.  If allowed, exten-
    sions can also use Forced Trunk Disconnect.  Additionally, extensions with Direct Trunk Access capability can
    dial 2 to Camp-On to a busy trunk.  This option also allows extensions to program System Speed Dial numbers.
    Conditions 
    None
    Default Value
    •Direct Trunk Access allowed (1) for COS 0.
    •Direct Trunk Access not allowed (0) for all other COSs.
    Feature Reference
    Call Waiting (Camp-On)
    Direct Trunk Access
    Forced Trunk Disconnect
    Instructions
    To enter data on the PRF:
    1. On Table 2 for BY2:0, enter 0 to prevent extensions with this COS from using Direct Trunk Access.  En-
    ter 1 to allow extensions with this COS to use Direct Trunk Access.
    To enter data at the programming terminal:
    1. Type CP.  You see: COS # 00: 00010000 00000-0 00000001 00000000
    2. Enter data for each COS you want to program.
    C- CLASS OF SERVICE
    CP- DIRECT TRUNK ACCESS AND TRUNK CAMP-ON (BY2:0)
    332   PROGRAMMING N1870SWG04   Issue 1-0 
    						
    							D- DISPLAY MEMORY
    Description
    This program displays the contents of system memory locations. It is a factory diagnostic tool, not intended for
    field use. Consult your Field Service representative for more information.
    Conditions 
    None
    Default Value
    None
    Feature Reference
    System Reports, Diagnostics and Maintenance Utilities
    Instructions
    None
    D- DISPLAY MEMORY
    N1870SWG04   Issue 1-0 PROGRAMMING   333 
    						
    All Nitsuko manuals Comments (0)

    Related Manuals for Nitsuko Digital System Feature And Terminal Programming Manual