Home
>
Multi-Tech Systems
>
Communications System
>
Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways User Guide
Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways User Guide
Have a look at the manual Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 104 Multi-Tech Systems manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
MultiVOIP User Guide Technical Configuration (Analog) 171 In the lower left corner of the screen, the connection status of the MultiVOIP will be displayed. The messages in the lower left corner will change as detection occurs. The message “MultiVOIP Found” confirms that the MultiVOIP is in contact with the MultiVOIP configuration program. Skip to step 5.
MultiVOIP User Guide Technical Configuration (Analog) 172 4.Solving Common Connection Problems. . A. Fixing a COM Port Problem. If the MultiVOIP main screen appears but is grayed out and seems inaccessible, the COM port that was specified for its communication with the PC is unavailable and must be changed. An error message will appear. To change the COM port setting, use the COM Port Setup dialog box, which is accessible via the keyboard shortcut Ctrl + G or by going to the Connection pull-down menu and choosing “Settings.” In the “Select Port” field, select a COM port that is available on the PC. (If no COM ports are currently available, re-allocate COM port resources in the computer’s MS Windows operating system to make one available.) Ctrl + G
MultiVOIP User Guide Technical Configuration (Analog) 173 4B. Fixing a Cabling Problem. If the MultiVOIP cannot be located by the computer, two error messages will appear (saying “Multi-VOIP Not Found” and “Phone Database Not Read”). In this case, the MultiVOIP is simply disconnected from the network. For instructions on MultiVOIP cable connections, see the Cabling section of Chapter 3. 5. Configuration Parameter Groups: Getting Familiar, Learning About Access. The first part of configuration concerns IP parameters, Voice/FAX parameters, Telephony Interface parameters, SNMP parameters, Regional parameters, SMTP parameters, Supplementary Services parameters, Logs, and System Information. In the MultiVOIP software, these seven types of parameters are grouped together under “Configuration” and each has its own dialog box for entering values. Generally, you can reach the dialog box for these parameter groups in one of four ways: pulldown menu, toolbar icon, keyboard shortcut, or sidebar. ..
MultiVOIP User Guide Technical Configuration (Analog) 174 6. Set IP Parameters. This dialog box can be reached by pulldown menu, toolbar icon, keyboard shortcut, or sidebar. Accessing “IP Parameters” Pulldown Icon Shortcut Sidebar Ctrl + Alt + I
MultiVOIP User Guide Technical Configuration (Analog) 175 In each field, enter the values that fit your particular network.
MultiVOIP User Guide Technical Configuration (Analog) 176 The IP Parameters fields are described in the table below. IP Parameter Definitions Field Name Values Description Enable DiffservY/N Diffserv is used for QoS (quality of service). When enabled, we configure the TOS (Type of Service) bits in the IP header so routers supporting Diffserv can give priority to the VOIP’s IP packets. Disabled by default. Frame Type Type II, SNAP Must be set to match network’s frame type. Default is Type II. IP Address 4-places, 0-255 The unique LAN IP address assigned to the MultiVOIP. IP Mask 4-places, 0-255 Subnetwork address that allows for sharing of IP addresses within a LAN. Gateway 4-places, 0-255. (feature not yet implemented; for future use)The IP address of the device that connects your MultiVOIP to the Internet. Enable DNS Y/N. (feature not yet implemented; for future use)Enables Domain Name Space/System function where computer names are resolved using a worldwide distributed database. DNS Server IP Address4-places, 0-255 IP address of specific DNS server to be used to resolve Internet computer names. FTP Server EnableY/N See “FTP Server File Transfers” in Operation & Maintenance chapter.MultiVOIP unit has an FTP Server function so that firmware and other important operating software files can be transferred to the voip via the network.
MultiVOIP User Guide Technical Configuration (Analog) 177 7. Enable Web Browser GUI (Optional). After an IP address for the MultiVOIP unit has been established, you can choose to do any further configuration of the unit (a) by using the MultiVOIP web browser GUI, or (b) by continuing to use the MultiVOIP Windows GUI. If you want to do configuration work using the web browser GUI, you must first enable it. To do so, follow the steps below. A. Set IP address of MultiVOIP unit using the MultiVOIP Configuration program (the Windows GUI). B. Save Setup in Windows GUI. C. Close Windows GUI. D. Install Java program from MultiVOIP product CD (on first use only). E. Open web browser. F. Browse to IP address of MultiVOIP unit. G. If username and password have been established, enter them when when prompted. H. Use web browser GUI to configure or operate MultiVOIP unit. The configuration screens in the web browser GUI will have the same content as their counterparts in the Windows GUI; only the graphic presentation will be different. For more details on enabling the MultiVOIP web GUI, see the “Web Browser Interface” section of the Operation & Maintenance chapter of this manual.
MultiVOIP User Guide Technical Configuration (Analog)
178
8. Set Voice/FAX Parameters. This dialog box can be reached by
pulldown menu, toolbar icon, keyboard shortcut, or sidebar.
Accessing “Voice/FAX Parameters”
Pulldown Icon
Shortcut Sidebar
Ctrl + H
MultiVOIP User Guide Technical Configuration (Analog) 179 In each field, enter the values that fit your particular network.
MultiVOIP User Guide Technical Configuration (Analog) 180 Note that Voice/FAX parameters are applied on a channel-by-channel basis. However, once you have established a set of Voice/FAX parameters for a particular channel, you can apply this entire set of Voice/FAX parameters to another channel by using the Copy Channel button and its dialog box. To copy a set of Voice/FAX parameters to all channels, select “Copy to All” and click Copy.