Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways User Guide

							MultiVOIP User Guide Overview
21
Analog MultiVOIP LED Descriptions
  
MVP-210/410/810 Front Panel LED Definitions
LED NAMEDESCRIPTION 
General Operation LEDs (one set on each MultiVOIP model)
PowerIndicates presence of power.
BootAfter power up, the Boot LED will be on briefly while the
MultiVOIP is booting.  It lights whenever the MultiVOIP is
booting or downloading a setup configuration data set.
EthernetRCV. Receive.  Lights (blinks) when receiving data on
Ethernet port.
XMT. Transmit.  Lights (blinks) when transmitting
data on Ethernet port. ..
LNK. Link.  When lit, VOIP “sees” the hub or network
via the Ethernet connection. ..
COL. Collision.  Lit when data collisions occur. ..
Channel-Operation LEDs  (one set for each channel)
XMTTransmit.  This indicator blinks when voice packets
are being transmitted to the local area network.
RCVReceive.    This indicator blinks when voice packets
are being received from the local area network. 
XSGTransmit Signal.  This indicator lights when the FXS-
configured channel is off-hook, the FXO-configured
channel is receiving a ring from the Telco, or the M
lead is active on the E&M configured channel.  That is,
it lights when the MultiVOIP is receiving a ring from
the PBX.
RSGReceive Signal.   This indicator lights when the FXS-
configured channel is ringing, the FXO-configured
channel has taken the line off-hook, or the E lead is
active on the E&M-configured channel. 
						

							Overview MultiVOIP User Guide
22
Computer Requirements
The computer on which the MultiVOIP’s configuration program is
installed must meet these requirements:
•must be IBM-compatible PC with MS Windows operating
system;
•must have an available COM port for connection to the
MultiVOIP.
However, this PC does not need to be connected to the MultiVOIP
permanently. It only needs to be connected when local configuration
and monitoring are done.  Nearly all configuration and monitoring
functions can be done remotely via the IP network. 
						

							MultiVOIP User Guide Overview
23
Specifications
Specs for Digital T1 MultiVOIP Units
Digital T1 MultiVOIP Specifications
Parameter
……/Model
MVP-2400 MVP-2410MVP-2410
w/ MVP24-48
Expansion
Card
Operating
Voltage(s)External
transformer:
1.6A@5v
100-240 VAC
1.2 - 0.6 A100-240 VAC
1.2 - 0.6 A
Mains
Frequencies50/60 Hz 50/60 Hz 50/60 Hz
Power
Consumption13 watts 17 watts 27 watts
Mechanical
Dimensions6.2” W x
9” D x
1.4” H
15.8cm W x
22.9cm D x
3.6cm H1.75”H x
17.4”W x
8.75”D
4.5cm H x
44.2 cm W x
22.2 cm D1.75”H x
17.4”W x
8.75”D
4.5cm H x
44.2 cm W x
22.2 cm D
Weight1.8lbs
(.82kg)
2.2lbs (.98kg)
with transformer7.1 lbs.
(3.2 kg)7.5 lbs.
(3.4 kg) 
						

							Overview MultiVOIP User Guide
24
Specs for Digital E1 MultiVOIP Units
Digital E1 MultiVOIP Specifications
Parameter
……/ModelMVP-3010 MVP-3010
w/ MVP30-60
Expansion
Card
Operating
Voltage(s)100-240 VAC
1.2 - 0.6 A100-240 VAC
1.2 - 0.6 A
Mains
Frequencies50/60 Hz 50/60 Hz
Power
Consumption17 watts 27 watts
Mechanical
Dimensions1.75”H x
17.4”W x
8.75”D
4.5cm H x
44.2 cm W x
22.2 cm D1.75”H x
17.4”W x
8.75”D
4.5cm H x
44.2 cm W x
22.2 cm D
Weight7.1 lbs.
(3.2 kg)7.5 lbs.
(3.4 kg) 
						

							MultiVOIP User Guide Overview
25
Specs for Analog MultiVOIP Units
Analog MultiVOIP Specifications
Parameter
……/ModelMVP210 MVP410 MVP810
or
MVP410 + 428
Operating
Voltage(s)External
transformer:
3A @5V100-240 VAC
1.2 - 0.6 A100-240 VAC
1.2 - 0.6 A
Mains
Frequencies50/60 Hz 50/60 Hz 50/60 Hz
Power
Consumption19 watts 29 watts 46 watts
Mechanical
Dimensions6.2” W x
9” D x
1.4” H
15.8cm W x
22.9cm D x
3.6cm H1.75”H x
17.4”W x
8.5”D
4.5cm H x
44.2 cm W x
21.6 cm D1.75”H x
17.4”W x
8.5”D
4.5cm H x
44.2 cm W x
21.6 cm D
Weight1.8lbs (.82kg)
2.6lbs (1.17kg)
with transformer7.1 lbs.
(3.2 kg)7.7 lbs.
(3.5 kg) 
						

							Overview MultiVOIP User Guide
26
Installation at a Glance
The basic steps of installing your MultiVOIP network involve
unpacking the units, connecting the cables, and configuring the units
using management software (MultiVOIP Configuration software) and
confirming connectivity with another voip site.  This process results in a
fully functional Voice-Over-IP network.
Related Documentation
The MultiVOIP User Guide (the document you are now reading) comes
in electronic form and is included on your system CD.  It presents in-
depth information on the features and functionality of Multi-Tech’s
MultiVOIP Product Family.
The CD media is produced using Adobe Acrobat
TM for viewing and
printing the user guide. To view or print your copy of a user guide,
load Acrobat Reader
TM on your system. The Acrobat Reader is included
on the MultiVOIP CD and is also a free download from Adobe’s Web
Site:
www.adobe.com/prodindex/acrobat/readstep.html
This MultiVOIP User Guide is also available on Multi-Tech’s Web site
at:
http://www.multitech.com
Viewing and printing a user guide from the Web also requires that you
have the Acrobat Reader loaded on your system.  To select the MultiVOIP
User Guide from the Multi-Tech Systems home page, click Documents and then click
MultiVOIP F a m i l y  in the product list drop-down window. All documents for this
MultiVOIP Product Family will be displayed.  You can then choose User Guide
(MultiVOIP Product Family) to view or download the .pdf file. 
						

							27
Chapter 2: Quick Start Instructions 
						

							Quick Start Instructions MultiVOIP User Guide
28
Introduction
This chapter gets the MultiVOIP up and running quickly.  The details
we’ve skipped to make this brief can be found elsewhere in the manual
(see Table of Contents and Index).
MultiVOIP Startup Tasks
TaskSummary




 
 Collecting Phone/IP
Details (vital!)
The MultiVOIP must be configured to
interface with your particular phone
system and IP network.  To do so,
certain details must be known about
those phone and IP systems.




 
 PlacementDecide where you’ll mount the voip.




 
 The Command/Control
Computer:
Specs & Settings
Some modest minimum specifications
must be met.  A COM port must be set
up.




 
 HookupConnect power, phone, and data cables
per diagram.




 
 Software InstallationThis is the configuration program.
It’s a standard Windows software
installation.




 
 Phone/IP Starter
Configuration
You will enter phone numbers and IP
addresses.  You’ll use default parameter
values where possible to get the system
running quickly.




 
 Phonebook Starter
Configuration
The phonebook is where you specify
how calls will be routed.  To get the
system running quickly, you’ll make
phonebooks for just two voip sites.




 
 Connectivity TestYou’ll find out if your voip system can
carry phone calls between two sites.
That means you’re up and running!




 
 TroubleshootingDetect and remedy any problems that
might have prevented connectivity. 
						

							MultiVOIP User Guide Quick Start Instructions
29
Phone/IP Details *Absolutely Needed*
Before Starting the Installation
  
Gather IP Information
➼Ask your computer network
administrator.Info needed to operate:
all MultiVOIP models.
IP Network Parameters:
Record for each VOIP Site
in System


• IP Address
• IP Mask
• Gateway
• Domain Name Server (DNS) Info
   
(not implemented; for future use)
Gather Telephone Information
➼T1 Phone Parameters
Ask phone company or
PBX maintainer.
Info needed to operate:
MVP2400
MVP2410
T1 Telephony Parameters:
Record for this VOIP Site


• Which frame format is used?  ESF___ or  D4___
• Which CAS or PRI protocol is used? ______________
• Clocking: Does the PBX or telco switch use
internal or external clocking? _________________
Note that the setting used in the voip unit will be the
opposite of the setting used by the telco/PBX.
• Which line coding is used?  AMI___ or  B8ZS___
• Pulse shape level?: (most commonly 0 to 40 meters) 
						

							Quick Start Instructions MultiVOIP User Guide
30
Phone/IP Details *Absolutely Needed*  (cont’d)
Gather Telephone Information
➼E1 Phone Parameters
Ask phone company or
PBX maintainer.
Info needed to operate:
MVP3010
E1 Telephony Parameters:
Record for this VOIP Site


• Which frame format is used?  Double Frame_____
MultiFrame w/ CRC4_____
MultiFrame w/ CRC4 modified_____
• Which CAS or PRI protocol is used? ______________
• Clocking: Does the PBX or telco switch use
internal or external clocking? _________________
Note that the setting used in the voip unit will be the
opposite of the setting used by the telco/PBX.
• Which line coding is used?  AMI___ or  HDB3___
• Pulse shape level?: (most commonly 0 to 40 meters)
  
      Gather Telephone Information
➼Analog Phone Parameters
Ask phone company or
telecom manager.
Needed for:
MVP810
MVP410
MVP210
Analog Telephony Interface Parameters:
Record for this VOIP Site


•  Which interface type (or “signaling”) is used?
                  
E&M_____    FXS/FXO_____
•  If FXS, determine whether the line will be used for a
phone, fax, or KTS (key telephone system)
• If FXO, determine if line will be an analog PBX
extension or an analog line from a telco central office
• If E&M, determine these aspects of the  E&M trunk
line from the PBX:
• What is its Type (1, 2, 3, 4, or 5)?
• Is it 2-wire or 4-wire?
• Is it Dial-Tone or Wink?