Konica Minolta bizhub 362 User Manual

							11Utility mode
11-50 362/282/222
Utility mode
Chapter 11
11.10 Specifying software switch settings (machine func-
tions)
By specifying the software switch settings (“Mode Selection”, “Bit Selection” 
and “Hex Selection”), various machine functions can be changed to meet 
your specific needs.
2
Reminder 
Do not change any modes or bits other than those described in this man-
ual.
2
Note 
When “Enhance Security” is set to “ON”, the software switch settings 
cannot be changed.
Software SW settings
Reference: Examples of “Bit Selection” binary numbers and “HEX Selection” 
hexadecimal numbers
ParameterDescription
Mode  Selection Specify the three-digit number for the parameter that you wish 
to specify with the software switch settings.
Bit Selection The bits are the eight numbers that construct the mode. By 
specifying a binary number (0 or 1) for each of the bits (0 
through 7), each function can be specified.
HEX Selection Specify a setting for each mode as a hexadecimal number (0 
through 9 and A through F).
For example, to specify the bit setting “0011 0000”, specify 
the hexadecimal setting “30”.
Decimal number“Bit Selection” setting (bina-
ry number)“HEX Selection” setting 
(hexadecimal number)
0 0000 0000 00
1 0000 0001 01
2 0000 0010 02
3 0000 0011 03
4 0000 0100 04
5 0000 0101 05
6 0000 0110 06
7 0000 0111 07
Downloaded From ManualsPrinter.com Manuals 
						

							Utility mode11
362/282/222 11-51
Utility mode
Chapter 11
To specify a software switch setting
1Enter Administrator mode, and then touch [Admin. 2].
2Touch [Software SW].
The soft SW Setting 
screen appears.
3Touch [Mode Selection], 
and then use the keypad 
to type in the mode 
number.
8 0000 1000 08
9 0000 1001 09
10 0000 1010 0A
11 0000 1011 0B
12 0000 1100 0C
13 0000 1101 0D
14 0000 1110 0E
15 0000 1111 0F
16 0001 0000 10
.
.
..
.
..
.
.
255 1111 1111 FF
Decimal number“Bit Selection” setting (bina-
ry number)“HEX Selection” setting 
(hexadecimal number)
Downloaded From ManualsPrinter.com Manuals 
						

							11Utility mode
11-52 362/282/222
Utility mode
Chapter 11
4Touch either [Bit Selec-
tion] or [HEX Selection], 
and then specify the set-
ting.
– To specify the bits, 
touch [Bit Selection], 
touch  and 
to move the cur-
sor to the bit to be 
changed, press ei-
ther the [0] or [1] key 
in the keypad to 
specify the bit, and then touch [Enter].
– To specify the hex 
value, touch [HEX 
Selection], specify 
the value by either 
using the keypad or 
touching [A] through 
[F], and then touch 
[Enter].
5To change the setting for a different mode, repeat steps 3 and 4.
6Touch [Enter] in each screen until the initial screen appears.
7Turn the machine off, then on again.
2
Reminder 
When turning the main power switch off, then on again, wait about 10 
seconds after turning the machine off before turning it on again. The ma-
chine may not operate correctly if it is turned on immediately after being 
turned off.
Downloaded From ManualsPrinter.com Manuals 
						

							Utility mode11
362/282/222 11-53
Utility mode
Chapter 11
Specifying permissions for copy functions (mode 307)
The machine can be set so that copy functions cannot be used. In this case, 
the Basics screen does not appear, even after the [Copy] key is pressed.
Settings at time of purchase
Specifying the setting
The shaded cells indicate the settings selected at the time of purchase.
Specifying the enlarged display method (mode 311)
Specify the method for displaying enlargements of screens.
Settings at time of purchase
Specifying the setting
The shaded cells indicate the settings selected at the time of purchase.
Bit 7 6 5 4 3 2 1 0
Setting 0 0 0 0 0 0 0 0 (HEX: 00)
BitDescriptionSettingDescription
7Specify whether or 
not copy functions 
can be used.
0 Specifies that copy 
functions can be 
used.
1 Specifies that copy 
functions cannot be 
used.
6, 5, 4, 3, 2, 1, 0 -----------------------
0000000*Do not change these 
bits when specifying 
settings for this func-
tion.
Bit 7 6 5 4 3 2 1 0
Setting 0 0 0 0 0 0 0 0 (HEX: 00)
BitDescriptionSettingDescription
7 -----------------------
0*Do not change this 
bit when specifying 
settings for this func-
tion.
Downloaded From ManualsPrinter.com Manuals 
						

							11Utility mode
11-54 362/282/222
Utility mode
Chapter 11Specifying that the “Auto Paper Select” setting and the “Auto Zoom” 
setting can be selected at the same time (mode 403)
If a paper tray is selected while the “Auto Paper Select” setting is specified, 
the “Auto Zoom” setting can be set automatically.
Settings at time of purchase
Specifying the setting
The shaded cells indicate the settings selected at the time of purchase.
6Specify whether to 
enlarge the upper-left 
corner of the screen 
or wait for instruc-
tions on the area to 
display enlarged 
when the [Enlarge 
Display] key is 
pressed.0 Waits for instructions 
on the area of the 
screen to be dis-
played enlarged.
1 Enlarges the upper-
left corner of the 
screen.
5, 4, 3, 2, 1, 0 -----------------------
000000*Do not change these 
bits when specifying 
settings for this func-
tion.
Bit 7 6 5 4 3 2 1 0
Setting 0 0 0 0 0 0 0 1 (HEX: 01)
BitDescriptionSettingDescription
7 -----------------------
0*Do not change this 
bit when specifying 
settings for this func-
tion.
6 Specifies the units 
used to display and 
specify lengths 
shown in the screens.
0 The “Auto Zoom” set-
ting cannot be speci-
fied at the same time.
1 The “Auto Zoom” set-
ting can be specified 
at the same time.
5, 4, 3, 2, 1, 0 -----------------------
000001*Do not change these 
bits when specifying 
settings for this func-
tion.
BitDescriptionSettingDescription
Downloaded From ManualsPrinter.com Manuals 
						

							Utility mode11
362/282/222 11-55
Utility mode
Chapter 11
Specifying the measurement units (mode 426)
Specify the units used to display and specify lengths shown in the screens.
Settings at time of purchase
Specifying the setting
The grayed out cells are the settings at the time of purchase.
Specifying settings when copying is finished using the ADF (mode 429)
Specify whether or not all settings are reset when copying is finished using 
the ADF.
Settings at time of purchase
Specifying the setting
The grayed out cells are the settings at the time of purchase.
Bit 7 6 5 4 3 2 1 0
Setting 0 1 0 1 0 0 0 0 (HEX: 50)
BitDescriptionSettingDescription
7, 6, 5 -----------------------
010*Do not change these 
bits when specifying 
settings for this func-
tion.
4, 3 Specifies the units 
used to display and 
specify lengths 
shown in the screens.00 Displayed in millime-
ters (mm)
01 Displayed in inches 
(decimals)
10 Displayed in inches 
(fractions)
2, 1, 0 -----------------------
000*Do not change these 
bits when specifying 
settings for this func-
tion.
Bit 7 6 5 4 3 2 1 0
Setting 0 0 0 0 0 0 0 0 (HEX: 00)
BitDescriptionSettingDescription
7, 6 -----------------------
00*Do not change these 
bits when specifying 
settings for this func-
tion.
Downloaded From ManualsPrinter.com Manuals 
						

							11Utility mode
11-56 362/282/222
Utility mode
Chapter 11
Specifying the pressing of the [Access] key when logging off (mode 438)
Select whether or not the [Access] key be pressed when logging off.
Settings at time of purchase
Specifying the setting
The shaded cells indicate the settings selected at the time of purchase.
Specifying use of registered user authentication information to log on to 
the LDAP server (mode 466)
Specify whether or not user names and passwords registered with user au-
thentication are used to log on to the LDAP server.
Settings at time of purchase
5 Specify whether or 
not all settings in the 
Basics screen are re-
set when copying is 
finished using the 
ADF.0 Automatic panel reset 
operation is not per-
formed.
1 Automatic panel reset 
operation is per-
formed.
4, 3, 2, 1, 0 -----------------------
00000*Do not change these 
bits when specifying 
settings for this func-
tion.
BitDescriptionSettingDescription
Bit 7 6 5 4 3 2 1 0
Setting 0 0 0 0 0 0 0 0 (HEX: 00)
BitDescriptionSettingDescription
7, 6, 5 -----------------------
000*Do not change these 
bits when specifying 
settings for this func-
tion.
4Specify whether or 
not the [Access] key 
be pressed when log-
ging off.
0 Specifies that the [Ac-
cess] key not be 
pressed when logging 
off.
1 Specifies that the [Ac-
cess] key be pressed 
when logging off.
3, 2, 1, 0 -----------------------
0000*Do not change these 
bits when specifying 
settings for this func-
tion.
Downloaded From ManualsPrinter.com Manuals 
						

							Utility mode11
362/282/222 11-57
Utility mode
Chapter 11
Specifying the setting
The shaded cells indicate the settings selected at the time of purchase.
!
Detail 
The information for the LDAP server to be connected to must be regis-
tered in order to use the LDAP server. In addition, when LDAP and user 
authentication is synchronized, select “Active Directory” as the user au-
thentication method. Select “GSS-SPNEGO” as the LDAP authentication 
method. For details on the user authentication method, refer to “To reg-
ister a user with external server authentication” on page 11-40. For de-
tails on the LDAP authentication method, refer to the User’s Guide 
[Network Scanner Operations].
Specifying whether to enable access locks and password rules, and 
specifying the method for deleting image data (mode 469)
Specify whether to lock access if the password is entered incorrectly, specify 
whether to apply the password rules, and specify the method for deleting im-
age data.
Settings at the time of purchase
Specifying the settings
The grayed out cells are the settings at the time of purchase.
Bit 7 6 5 4 3 2 1 0
Setting 0 0 0 0 0 0 0 0 (HEX: 00)
BitDescriptionSettingDescription
7 Select whether or not 
the user name/pass-
word used for exter-
nal server 
authentication is used 
to log on to the LDAP 
server.
0 Not used for logon
1 Used for logon
6, 5, 4, 3, 2, 1, 0 -----------------------
0000000*Do not change these 
bits when specifying 
settings for this func-
tion.
Bit 7 6 5 4 3 2 1 0
Setting 0 0 0 0 0 0 0 0 (HEX: 00)
Downloaded From ManualsPrinter.com Manuals 
						

							11Utility mode
11-58 362/282/222
Utility mode
Chapter 11
*1 This setting is applied after the machine is turned off, then on again.
!
Detail 
If “Enhance Security” is set to “ON”, the access lock, password rules and 
overwriting of temporary data are enabled. For details on the “Enhance 
Security” parameter, refer to “Specifying security settings (Security Set-
ting parameters)” on page 11-62.
The access lock can be canceled with each password. For details, refer 
to “Canceling an access lock (“Unlock” parameter)” on page 11-66.
For details on the password rules, refer to “Password rules” on 
page 11-70.
BitDescriptionSettingDescription
7 Specify whether to 
lock access when a 
password (account 
track and administra-
tor passwords) is en-
tered incorrectly three 
times.
0 Does not lock access
1 Locks access
6 Specify whether or 
not image data on the 
hard disk is overwrit-
ten to delete it.*1
0 Image data on the 
hard disk is not over-
written when it is de-
leted.
1 Image data on the 
hard disk is overwrit-
ten when it is deleted.
5 ---------------------
0*Do not change this 
bit when specitying 
settings for this func-
tion.
4 For security, specify 
whether to apply a 
password rule.
0 Do not apply a pass-
word rule
1 Apply a password rule
3, 2, 1, 0 ---------------------
0000*Do not change these 
bits when specifying 
settings for this func-
tion.
Downloaded From ManualsPrinter.com Manuals 
						

							Utility mode11
362/282/222 11-59
Utility mode
Chapter 11
2
Note 
If bit 6 is set to “1”, the scanning and printing speed may be reduced.
Specifying the setting for displaying a list of users in the User Authenti-
cation screen (mode 471)
Specify whether or not [User List] appears in the screen for machine authen-
tication and specify the screen that appears as a default when [User List] is 
touched.
Settings at time of purchase
Specifying the setting
The grayed out cells are the settings at the time of purchase.
Specifying the deleting method for [Del.] in input screens (mode 478)
Specify the deleting method for [Del.] in input screens.
Select whether the character at the cursor’s position or the character to the 
left of the cursor is deleted.
Settings at time of purchase
Bit 7 6 5 4 3 2 1 0
Setting 0 0 0 0 0 0 0 0 (HEX: 00)
BitDescriptionSettingDescription
7, 6, 5, 4, 3 -----------------------
00000*Do not change these 
bits when specifying 
settings for this func-
tion.
2, 1 Specifies whether or 
not the user list is dis-
played and whether 
or not the user list is 
the default.
00 Does not display the 
user list.
01 Displays the user list, 
but does not specify it 
as the default.
11 Specifies the user list 
as the default.
0 -----------------------
0*Do not change this 
bit when specitying 
settings for this func-
tion.
Bit 7 6 5 4 3 2 1 0
Setting 1 0 0 0 0 0 0 0 (HEX: 80)
Downloaded From ManualsPrinter.com Manuals