Konica Minolta bizhub 362 User Manual

							3Basic copy operation
3-36 362/282/222
Basic copy operation
Chapter 3
Selecting a stored zoom ratio
C o p y  z o o m  r a t i o s  t h a t  h a v e  b e e n  s t o r e d  c a n  b e  r e c a l l e d  t o  b e  u s e d  w h e n  d e -
sired.
In addition, stored copy zoom ratios can be changed.
0Stored zoom ratios can be changed to desired zoom ratios. For details 
on storing zoom ratios, refer to “Storing the desired zoom ratio” on 
page 3-37.
0The zoom ratios ×1.000, ×1.000 and ×0.930 have been stored.
1In the Basics screen, 
touch [Zoom].
The Zoom screen ap-
pears.
2Touch [XY Zoom].
The XY Zoom screen ap-
pears.
3Touch the button for the 
desired zoom ratio.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-37
Basic copy operation
Chapter 3
4Touch [Enter].
The Zoom screen appears again.
Storing the desired zoom ratio
Two frequently used zoom ratios and the zoom ratio for the “Minimal” setting 
can be stored.
0The zoom ratios ×1.000, ×1.000 and ×0.930 have been stored. When a 
new zoom ratio is stored, it overwrites the zoom ratio stored with the se-
lected button.
1In the Basics screen, 
touch [Zoom].
The Zoom screen ap-
pears.
2Touch [XY Zoom].
The XY Zoom screen ap-
pears.
Downloaded From ManualsPrinter.com Manuals 
						

							3Basic copy operation
3-38 362/282/222
Basic copy operation
Chapter 3
3Touch [Set Zoom].
The Set Zoom screen 
appears.
4Using the keypad, type 
in the desired zoom ratio 
(between ×0.250 and 
×4.000).
– If a value outside the 
allowable range is 
specified, the mes-
sage “Input Error” 
appears. Type a val-
ue within the allowa-
ble range.
– If the value was in-
correctly entered, press the [C] (clear) key in the keypad to erase the 
value, and then specify the correct value.
– To store a “Minimal” zoom ratio, type in the desired zoom ratio be-
tween ×0.900 and ×0.999.
5Touch the button or 
[Minimal] where the new 
zoom ratio is to be 
stored.
6Touch [Enter].
The XY Zoom screen appears again.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-39
Basic copy operation
Chapter 3
3.7 Selecting single-/double-sided settings for originals 
and copies
The following four combinations of the “Single-Sided” and “Double-Sided” 
settings are available originals and copies.
Original/copy settingsDescription
Single-Sided % Single-Sided Select this setting to produce single-sided copies from sin-
gle-sided documents.
Single-Sided % Double-Sided Select this setting to produce one double-sided copy from 
two single-sided documents.
Double-Sided % Single-Sided Select this setting to produce two single-sided copies from 
one double-sided document.
11
21
2
1
21
2
1
Downloaded From ManualsPrinter.com Manuals 
						

							3Basic copy operation
3-40 362/282/222
Basic copy operation
Chapter 3To select single-sided copies
0As a factory default, the “Single-Sided” Original setting and the “Single-
Sided” Copy setting are selected.
0If the “Double-Sided” Original setting and the “Single-Sided” Copy set-
ting are selected, specify the position of the binding margin and the load-
ing orientation for the document, otherwise the copies will not be printed 
as desired. For details on specifying the position of the binding margin, 
refer to “Selecting the position of the binding margin (Margin settings)” on 
page 3-21. For details on specifying the document orientation, refer to 
“Selecting the document orientation (Original Direction settings)” on 
page 3-19.
0For details on using the original glass to scan multiple document pages, 
refer to “Scanning a multi-page document from the original glass” on 
page 3-14.
1In the Basics screen, 
touch [Simplex/Duplex].
The Simplex/Duplex 
screen appears.
Double-Sided % Double-Sided Select this setting to produce double-sided copies from 
double-sided documents.
Original/copy settingsDescription
2
1
2
1
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-41
Basic copy operation
Chapter 3
2Select the single-sided 
copy settings according 
to the loaded document.
– For a single-sided 
document, touch 
[Single-Sided] under 
“Orig.” and [Single-
Sided] under “Copy”.
– For a double-sided 
document, touch 
[Double-Sided] un-
der “Orig.” and [Sin-
gle-Sided] under “Copy”.
To select double-sided copies
0As a factory default, the “Single-Sided” Original setting and the “Single-
Sided” Copy setting are selected.
0If the “Double-Sided” Copy setting is selected, specify the position of the 
binding margin and the loading orientation for the document, otherwise 
the copies will not be printed as desired.
For details on specifying the position of the binding margin, refer to “Se-
lecting the position of the binding margin (Margin settings)” on 
page 3-21.
For details on specifying the document orientation, refer to “Selecting the 
document orientation (Original Direction settings)” on page 3-19.
0For details on using the original glass to scan multiple document pages, 
refer to “Scanning a multi-page document from the original glass” on 
page 3-14.
1In the Basics screen, 
touch [Simplex/Duplex].
The Simplex/Duplex 
screen appears.
Downloaded From ManualsPrinter.com Manuals 
						

							3Basic copy operation
3-42 362/282/222
Basic copy operation
Chapter 3
2Select the double-sided 
copy settings according 
to the loaded document.
– For a single-sided 
document, touch 
[Single-Sided] under 
“Orig.” and [Double-
Sided] under “Copy”.
– For a double-sided 
document, touch 
[Double-Sided] un-
der “Orig.” and [Dou-
ble-Sided] under “Copy”.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-43
Basic copy operation
Chapter 3
3.8 Specifying document quality/density settings
Select the setting for the text and image type of the document to better ad-
just the copy quality.
The following Quality/Density settings are available.
Document Quality Types
Density Adjustment
IconDescription
Select this setting when copying documents containing only 
text.
The edges of copied text are reproduced with sharpness, 
providing text that is easy to read.
Select this setting when copying printed documents contain-
ing both text and images, such as pamphlets or catalogs.
Select this setting when copying printed documents, such as 
pamphlets or catalogs.
Select this setting to produce better reproductions of half-
tone document images (photographs, etc.) that cannot be re-
produced with the usual copy settings.
Select this setting when copying documents containing only 
text, where some of the text appears faint (such as that writ-
ten with a pencil).
The copied text is reproduced so that it is darker, making it 
easier to read.
Text
Text & Photo
Photo
Dot Matrix
IconDescription
The density can be adjusted to one of nine levels.
Each time [Dark] is touched, the density is darkened by one 
level. Each time [Light] is touched, the density is lightened by 
one level.
Select this setting to automatically adjust the density accord-
ing to the document that is loaded.
Downloaded From ManualsPrinter.com Manuals 
						

							3Basic copy operation
3-44 362/282/222
Basic copy operation
Chapter 3
Specifying a document quality setting
0The factory default setting is “Text & Photo”.
0For details on positioning the document, refer to “Feeding the document” 
on page 3-8.
1Position the document to be copied.
2In the Basics screen, 
touch [Quality/Density].
The Quality/Density 
screen appears.
3Touch the button for the 
quality setting most ap-
propriate for the loaded 
document.
– For a document that 
contains only text, 
touch [Text].
– For a document that 
contains both text 
and photos, touch 
[Text & Photo].
– For a document that 
contains photos, touch [Photo].
– For a document that contains faint text, touch [Dot Matrix].
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-45
Basic copy operation
Chapter 3
Adjusting the Copy Density (Density settings)
0The default setting is the middle of the five levels. When the “Auto” set-
ting is selected, the “Std.” Density setting is set.
0The default Density setting and the density selected when the “Auto” set-
ting is selected can be changed from the Utility mode. For details, refer 
to “Default Copy Output Levels” on page 11-14.
1In the Basics screen, 
touch [Quality/Density].
The Quality/Density 
screen appears.
2Select the desired Den-
sity setting.
– Each time [Light] or 
[Dark] is touched, the 
density is lightened 
or darkened by one 
level.
– Touch [Auto] to auto-
matically adjust the 
density according to 
the document that is 
loaded.
Downloaded From ManualsPrinter.com Manuals