Konica Minolta bizhub 362 User Manual

							2Before making copies
2-62 362/282/222
Before making copies
Chapter 2
2
Reminder 
For details on the paper sizes, refer to “Copy paper” on page 7-2.
2
Reminder 
When loading postcards, load them in the w orientation, as shown. Do 
not load postcards in the v orientation.
A maximum of 50 postcards can be loaded into the bypass tray.
2
Reminder 
A maximum of 50 overhead projector transparencies can be loaded into 
the bypass tray.
Downloaded From ManualsPrinter.com Manuals 
						

							Before making copies2
362/282/222 2-63
Before making copies
Chapter 2
2
Reminder 
Before loading envelopes, press them down to make sure that all air is 
removed, and make sure that the folds of the flaps are firmly pressed, 
otherwise the envelopes may become wrinkled or a paper misfeed may 
occur.
When loading envelopes, load them with the flap side up, as shown. If the 
envelopes are loaded with the flap side down, a paper misfeed may oc-
cur. The flap side of envelopes cannot be printed on.
A maximum of 10 envelopes can be loaded into the bypass tray.
After you have loaded the paper, set the paper type for the bypass tray 
in the touch panel. 
If the Envelope setting was set, the loaded document is copied upside-
down.
Flap side
Downloaded From ManualsPrinter.com Manuals 
						

							2Before making copies
2-64 362/282/222
Before making copies
Chapter 2
2
Reminder 
Be sure to load label sheets so that the side to be printed on faces down.
A maximum of 50 label sheets can be loaded into the bypass tray.
2
Reminder 
A maximum of 150 sheets of thin paper can be loaded into the bypass 
tray.
2
Note 
The image will be printed on the surface of the paper facing down when 
the paper is loaded into the bypass tray.
Downloaded From ManualsPrinter.com Manuals 
						

							Before making copies2
362/282/222 2-65
Before making copies
Chapter 2
!
Detail 
For details on specifying the paper size for the bypass tray, refer to “To 
specify the paper size (Change Setting)” on page 7-8.
Downloaded From ManualsPrinter.com Manuals 
						

							2Before making copies
2-66 362/282/222
Before making copies
Chapter 2
Downloaded From ManualsPrinter.com Manuals 
						

							3
Basic copy operation
Chapter 3
Basic copy operation
Downloaded From ManualsPrinter.com Manuals 
						

							3Basic copy operation
3-2 362/282/222
Basic copy operation
Chapter 3
3 Basic copy operation
3.1 General copy operation
This section contains information on the general operation for making cop-
ies.
The following procedure describes how to copy a single-sided document us-
ing basic copy operations.
2
Note 
Some settings cannot be used together.
For details on the settings that cannot be combined, refer to “Operations 
that cannot be combined” on page 3-5.
To make a copy
1Press the [Copy] key to display the Basics screen in Copy mode.
2Position the document to be copied.
– For details on positioning the document, refer to “Feeding the doc-
ument” on page 3-8.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-3
Basic copy operation
Chapter 3
3Specify the desired copy 
settings.
– The factory default 
settings for this ma-
chine are listed be-
low.
Paper: Auto Paper
Zoom: ×1.000 (Full 
size)
Simplex/Duplex: 1 % 
1
Quality/Density: Text
– For details on specifying document settings, refer to “Specifying 
document settings” on page 3-16.
– For details on selecting a paper source setting, refer to “Selecting 
a Paper setting” on page 3-24.
– For details on specifying a Zoom setting, refer to “Specifying a 
Zoom setting” on page 3-27.
– For details on selecting a Simplex/Duplex setting, refer to “Select-
ing single-/double-sided settings for originals and copies” on 
page 3-39.
– For details on selecting the quality of the document and the copy 
density, refer to “Specifying document quality/density settings” on 
page 3-43.
– For details on specifying combined copy settings, refer to “Select-
ing a Combine Originals setting” on page 3-46.
– For details on specifying Finishing settings, refer to “Selecting fin-
ishing for copies” on page 3-50.
– For details on selecting the binding setting, refer to “Creating book-
let copies (“Booklet” function)” on page 8-22.
– For details on specifying settings for the Application functions, refer 
to “Application functions” on page 8-2.
4Using the keypad, type 
in the desired number of 
copies.
– If the number of cop-
ies was incorrectly 
entered, press the 
[C] (clear) key in the 
keypad, and then 
specify the correct 
number of copies.
Downloaded From ManualsPrinter.com Manuals 
						

							3Basic copy operation
3-4 362/282/222
Basic copy operation
Chapter 3
5Press the [Start] key.
– To stop the copy op-
eration being per-
formed, press the 
[Stop] key. For de-
tails, refer to “Stop-
ping/deleting a job” 
on page 3-63.
– The next copy opera-
tion can be queued 
while a copy opera-
tion is being per-
formed. For details, 
refer to “Scanning the next document during printing (reserving a 
copy job)” on page 3-61.
2
Note 
If the optional hard disk drive is installed, [Save in User Box] appears in 
the Copy mode screen. If copies are made with “Save in User Box” se-
lected, the contents of the copied documents are saved in boxes.
For details on boxes, refer to the User’s Guide [Box Operations].
!
Detail 
A function other than a copy function cannot be selected while pages are 
being scanned for copying or while copying is paused.
Stop
Start
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-5
Basic copy operation
Chapter 3
3.2 Operations that cannot be combined
Certain copy settings cannot be used together.
Specifying settings that cannot be combined will result in one of the follow-
ing.
-The setting specified last is given priority. (The setting specified first is 
canceled.)
-The setting specified first is given priority. (A warning message appears.)
2
Note 
Depending on the combined operations and the selected paper type, 
some settings that can be specified may not be applied.
Operations where the setting specified last is given priority
The procedure for setting the “Book Copy” function after selecting the “4 in 
1”setting is described below.
1Select the “4 in 1” set-
ting.
Downloaded From ManualsPrinter.com Manuals