Konica Minolta bizhub 362 User Manual

							7Copy paper/original documents
7-10 362/282/222
Copy paper/original documents
Chapter 7
To specify a non-standard paper size (Custom Size settings)
Non-standard-sized paper can be loaded only into the bypass tray.
If non-standard-sized paper is loaded, it will be necessary to specify the pa-
per size.
1In the Basics screen, 
touch [Paper].
The Paper screen ap-
pears.
2Select the button for the 
bypass tray.
3Touch [Change Setting].
Downloaded From ManualsPrinter.com Manuals 
						

							Copy paper/original documents7
362/282/222 7-11
Copy paper/original documents
Chapter 7
4Touch [Custom Size].
The Custom Size screen 
appears.
?How can the size of paper loaded into the bypass tray be selected?
%For details, refer to “To specify a setting for special paper (Change 
Setting)” on page 7-15.
5Type in the length (X) 
and width (Y) of the pa-
per.
– Make sure that [X] is 
selected, and then 
use the keypad to 
type in the length of 
side X (between 5.50 
and 17.00).
– Touch [Y] to select it, 
and then use the 
keypad to type in the 
length of side Y (between 3.56 and 11.68).
– If “Inch (Fraction)” was selected as the measurement units, touch 
[X] or [Y] to position the cursor in the input box, and then touch 
 or   to specify the length.
– A value outside the allowable range cannot be entered.
– To change the entered value, press the [C] (clear) key, and then en-
ter the correct value.
?Can paper sizes be stored?
%Two specified non-standard paper sizes can be stored. For details, 
refer to “To store a non-standard paper size (Custom Size settings)” 
on page 7-12.
%To recall a stored paper size, touch [1] or [2].
6Touch [Enter].
The Paper screen appears again.
A non-standard paper size is specified.
Downloaded From ManualsPrinter.com Manuals 
						

							7Copy paper/original documents
7-12 362/282/222
Copy paper/original documents
Chapter 7
To store a non-standard paper size (Custom Size settings)
Two non-standard paper sizes for the bypass tray can be stored.
Storing paper sizes that are used often allows the paper size to be quickly 
selected, without having to re-enter the setting.
1In the Basics screen, 
touch [Paper].
The Paper screen ap-
pears.
2Select the button for the 
bypass tray.
3Touch [Change Setting].
Downloaded From ManualsPrinter.com Manuals 
						

							Copy paper/original documents7
362/282/222 7-13
Copy paper/original documents
Chapter 7
4Touch [Custom Size].
The Custom Size screen 
appears.
?How can the size of paper loaded into the bypass tray be selected?
%For details, refer to “To specify a setting for special paper (Change 
Setting)” on page 7-15.
5Touch [Size Registra-
tion].
The Size Registration 
screen appears.
6Type in the length (X) 
and width (Y) of the pa-
per.
– Make sure that [X] is 
selected, and then 
use the keypad to 
type in the length of 
side X (between 5.50 
and 17.00).
– Touch [Y] to select it, 
and then use the 
keypad to type in the 
length of side Y (between 3.56 and 11.68).
– If “Inch (Fraction)” was selected as the measurement units, touch 
[X] or [Y] to position the cursor in the input box, and then touch 
 or   to specify the length.
– A value outside the allowable range cannot be entered.
Downloaded From ManualsPrinter.com Manuals 
						

							7Copy paper/original documents
7-14 362/282/222
Copy paper/original documents
Chapter 7
– To change the entered value, press the [C] (clear) key, and then en-
ter the correct value.
7Touch [1] or [2] to specify where the size is to be stored.
– If a button is pressed where no size is stored, the stored paper size 
appears on the button to indicate that a size has been stored.
?How is the stored paper size recalled?
%Touch [1] or [2] in the Custom Size screen to recall the stored paper 
size.
8Touch [Enter], and then touch [Enter] in the next screen that appears.
The Paper screen appears again.
The non-standard paper size is stored.
No program registered Program registered
Downloaded From ManualsPrinter.com Manuals 
						

							Copy paper/original documents7
362/282/222 7-15
Copy paper/original documents
Chapter 7
To specify a setting for special paper (Change Setting)
If a setting for special paper, such as overhead projector transparencies and 
other special paper, is selected for a paper tray, that tray is not selected au-
tomatically with the “Auto Paper Select” setting or the automatic paper-tray-
switching feature. However, a paper tray set to “Single Sided Only” is given 
priority when the “Auto Paper Select” setting is specified.
The following procedure describes how to specify the setting for overhead 
projector transparencies, thick paper, thin paper or envelopes loaded into 
the bypass tray.
1In the Basics screen, 
touch [Paper].
The Paper screen ap-
pears.
2Select the button for the 
bypass tray.
3Touch [Change Setting].
Downloaded From ManualsPrinter.com Manuals 
						

							7Copy paper/original documents
7-16 362/282/222
Copy paper/original documents
Chapter 7
4Select the desired spe-
cial paper type.
?What types of paper 
can be loaded into 
each paper tray?
%There are limits on 
the types of paper 
that can be loaded in 
a paper tray. For de-
tails on the types of 
paper that can load-
ed, refer to “Specifications” on page 6-2 and “Paper types and pa-
per capacities” on page 7-4.
5Touch [Enter].
The Paper screen appears again.
The paper type for the bypass tray is set.
2
Reminder 
If overhead projector transparencies or thick paper is loaded into the by-
pass tray, be sure to select the corresponding paper type, otherwise a 
paper misfeed may occur.
!
Detail 
For details on the special paper, refer to “Special paper” on page 7-5.
For details on specifying the settings for paper only for single-sided cop-
ying, for recycled paper and for special paper, refer to “Special Paper 
Setting” on page 11-12.
The settings for overhead projector transparencies, thick paper, thin pa-
per and envelopes can also be specified for the bypass tray, even if a set-
ting for paper only for single-sided copying, for recycled paper and for 
special paper is specified.
Downloaded From ManualsPrinter.com Manuals 
						

							Copy paper/original documents7
362/282/222 7-17
Copy paper/original documents
Chapter 7
7.3 Original documents
When making copies, load the document into the ADF or position it on the 
original glass.
To copy documents that cannot be loaded into the ADF, position them on 
the original glass.
Documents that can be loaded Into the ADF
There are two methods for using the ADF.
-Normal method
-For documents of mixed sizes
There are limits on the types of documents that can be loaded with each 
method.
Normal method
For documents of mixed sizes
Single-sided documentsDouble-sided documents
Document paper type/
WeightPlain paper: 9-1/4 lb to 34 lb Plain paper: 13-1/4 lb to 34 lb
Document size 11 × 17 w to 5-1/2 × 8-1/2 w
Paper capacity 80 sheets (21-1/4 lb paper)
Single-sided documentsDouble-sided documents
Document paper type/
WeightPlain paper: 13-1/4 lb to 34 lb
Document size Refer to “Copying documents of mixed sizes (“Mixed Original” set-
ting)” on page 3-16.
Paper capacity 80 sheets (21-1/4 lb paper)
Downloaded From ManualsPrinter.com Manuals 
						

							7Copy paper/original documents
7-18 362/282/222
Copy paper/original documents
Chapter 7
Precautions for loading documents Into the ADF
The following types of documents should not be loaded into the ADF, other-
wise paper misfeeds or damage to the document may occur.
-Wrinkled, folded, curled, or torn documents
-Highly translucent or transparent documents, such as overhead trans-
parencies or diazo photosensitive paper
-Coated documents such as carbon-backed paper
-Documents printed on paper thicker than 34-1/4 lb
-Documents that are bound, for example, with staples or paper clips
-Documents that are bound in a book or booklet
-Documents that are bound together with glue
-Document pages that have had cutouts removed or are cutouts
-Label sheets
-Offset printing masters
-Documents with binder holes
-Documents that have just been printed with this machine
2
Reminder 
Before loading folded documents, such as those folded in half or in a zig-
zag, into the ADF, be sure to flatten the pages.
Downloaded From ManualsPrinter.com Manuals 
						

							Copy paper/original documents7
362/282/222 7-19
Copy paper/original documents
Chapter 7
Documents that can be placed on the original glass
To copy documents that cannot be loaded into the ADF, position them on 
the original glass.
Precautions for positioning documents on the original glass
Observe the following precautions when placing the document on the origi-
nal glass.
-The size of documents printed on paper in metric sizes (such as A3, B4 
and A4) cannot be automatically detected. The setting must be specified 
by the technical representative. For details, contact the technical repre-
sentative.
-If a document of non-standard paper size is loaded, the “Auto Paper Se-
lect” and “Auto Zoom” settings cannot be used since the document size 
cannot be detected automatically. If a document of non-standard paper 
size is loaded, select the size of the paper to be copied.
-If highly translucent or transparent documents, such as overhead trans-
parencies or diazo photosensitive paper, are loaded, the document size 
cannot be detected automatically. Place a blank sheet of paper of the 
same size over the document.
-Do not place objects exceeding 4-1/2 lb on the original glass, otherwise 
the original glass may be damaged.
-If a book is placed on the original glass, do not press it down extremely 
hard, otherwise the original glass may be damaged.
Original glass documents
Document type Sheets, books (page spreads), three-dimensional objects
Document size 11 × 17 w or less
Maximum weight 4-1/2 lb
Downloaded From ManualsPrinter.com Manuals