Konica Minolta bizhub 362 User Manual

							3Basic copy operation
3-16 362/282/222
Basic copy operation
Chapter 3
3.4 Specifying document settings
The following procedure describes how to specify the type of document to 
be copied.
Copying documents of mixed sizes (“Mixed Original” setting)
Documents of different sizes can be loaded together into the ADF to be fed 
and scanned one by one automatically.
Mixed originals paper sizes
The following chart shows the possible combinations of standard-sized pa-
per that can be used with the “Mixed Original” setting.
o: Possible
—: Not possible
To copy documents with the “Mixed Original” setting
0The possible combinations of document sizes differ depending on the 
widest document loaded (position of the adjustable document guides of 
the ADF).
0
*1 Indicates the width of the widest document size of the mixed originals 
(width of the adjustable document guides of the ADF).
0
*2 Indicates document sizes that can be specified together with the max-
imum document width.
1Slide the adjustable document guides to fit the size of the largest page.
Maximum Document 
Width*1→11 × 17 
wLetter vLegal wLetter 
w5-1/2 × 
8-1/2
v5-1/2 × 
8-1/2 
w
↓ Document Size*2
11 × 17 woo————
Letter voo————
Legal w ooooo—
Letter w ooooo—
5-1/2 × 8-1/2 v——ooo—
5-1/2 × 8-1/2 w—————o
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-17
Basic copy operation
Chapter 3
2Arrange the document pages so that the side to be copied (first page) 
faces up, as shown in the illustration.
3Load the document face 
up in the document feed 
tray.
Slide the adjustable doc-
ument guides against 
the edges of the docu-
ment.
– Load the document 
pages into the ADF 
so that the top of the 
pages is toward the 
back or the left side 
of the machine.
– If the document is not loaded correctly, it may not be fed in straight 
or a document misfeed or damage to the document may occur.
4In the Basics screen, 
touch [Mixed Original].
– To cancel the “Mixed 
Original” setting, 
touch [Mixed Origi-
nal] again to deselect 
it.
Adjustable document guide
Downloaded From ManualsPrinter.com Manuals 
						

							3Basic copy operation
3-18 362/282/222
Basic copy operation
Chapter 3
5Press the [Start] key.
Scanning begins.
!
Detail 
Do not load more than 80 sheets or so many sheets that the top of the 
stack is higher than the , mark, otherwise a document misfeed or dam-
age to the document or machine may occur. However, a document that 
exceeds 80 pages can be scanned in separate batches. For details, refer 
to “Scanning a document in separate batches (“Separate Scan” setting)” 
on page 3-12.
2
Note 
If the “Mixed Original” setting was selected, double-sided copying can-
not be selected.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-19
Basic copy operation
Chapter 3
Selecting the document orientation (Original Direction settings)
When copying double-sided documents, making double-sided copies, or 
using a combined copy setting, specify the document orientation, otherwise 
the copies may not be printed in the correct page order or correct front and 
back page arrangement.
2
Note 
The factory default setting is the first setting (with the top of the document 
at the top (toward the back of the machine)).
Document Loading Orientation
Using the ADFUsing the original 
glassIconDescription
Select this setting for a document 
loaded with the top toward the 
back of this machine.
Select this setting for a document 
loaded with the top to the left 
side of this machine.
1
1
1
1
Downloaded From ManualsPrinter.com Manuals 
						

							3Basic copy operation
3-20 362/282/222
Basic copy operation
Chapter 3
To select an Original Direction setting
0For details on positioning the document, refer to “Feeding the document” 
on page 3-8.
1Position the document to be copied.
2In the Basics screen, 
touch [Combine Origi-
nals].
The Combine Originals 
screen appears.
3Touch [Original Direc-
tion].
The Original Direction 
screen appears.
4Select the document ori-
entation. Touch the but-
ton for the orientation of 
the loaded document, 
and then touch [Enter].
– To cancel the Origi-
nal Direction setting, 
touch [OFF].
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-21
Basic copy operation
Chapter 3
Selecting the position of the binding margin (Margin settings)
When making single-sided copies of double-sided documents with a binding 
margin, or when making double-sided copies of single-sided documents 
with a binding margin, the position of the binding margin for the even-num-
bered pages can be adjusted.
2
Note 
As the factory default, “OFF” is selected for the Margin setting.
Document Binding Margin Position
IconDescription
Select this setting if the document that is loaded has a binding margin on the 
left.
• Single-sided copies of double-sided documents
• Double-sided copies of single-sided documents
Select this setting if the document that is loaded has a binding margin at the 
top.
• Single-sided copies of double-sided documents
ABCDE
DEF
ABC
ABCDE
DEF
ABC
ABC
DEF
DEF
ABC
Downloaded From ManualsPrinter.com Manuals 
						

							3Basic copy operation
3-22 362/282/222
Basic copy operation
Chapter 3
• Double-sided copies of single-sided documents
IconDescription
ABC
DEF
DEF
ABC
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-23
Basic copy operation
Chapter 3
To select a Margin setting
0For details on positioning the document, refer to “Feeding the document” 
on page 3-8.
1Position the document to be copied.
– When loading a document with a binding margin, position the top 
of the document toward the back of the machine.
2In the Basics screen, 
touch [Combine Origi-
nals].
The Combine Originals 
screen appears.
3Touch [Margin].
The Margin screen ap-
pears.
4Select the binding mar-
gin position. Touch the 
button for a left binding 
margin or for a top bind-
ing margin, and then 
touch [Enter].
– To cancel the Margin 
setting, touch [OFF].
Downloaded From ManualsPrinter.com Manuals 
						

							3Basic copy operation
3-24 362/282/222
Basic copy operation
Chapter 3
3.5 Selecting a Paper setting
The paper size can be selected automatically according to the document 
size or it can be specified manually. Specify the paper size according to the 
corresponding procedure, depending on the desired copy settings.
2
Note 
The factory default setting is “Auto Paper Select”.
As a factory default, the “Auto Zoom” setting and the “Auto Paper Select” 
setting cannot both be selected at the same time. If the “Auto Paper Se-
lect” setting is selected while the “Auto Zoom” setting was selected, the 
Zoom setting “×1.0” is selected.
However, the software switch settings can be used to allow the “Auto 
Zoom” setting and the “Auto Paper Select” setting to be selected at the 
same time. For details on the software switch settings, refer to “Specify-
ing software switch settings (machine functions)” on page 11-50.
Automatically selecting the paper size (“Auto Paper Select” setting)
The size of the loaded document is detected, and copies are produced using 
paper of the same size.
If the “×1.0” Zoom setting was specified, paper of the same size as the doc-
ument is selected.
If the zoom ratio was increased or decreased, a paper size that corresponds 
to the specified zoom ratio is automatically selected.
1In the Basics screen, 
touch [Paper].
The Paper screen ap-
pears.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-25
Basic copy operation
Chapter 3
2Touch [Auto Paper Se-
lect].
!
Detail 
If the document size cannot be detected, remove the document, and then 
load it again.
If a document with an irregular size is loaded, specify the paper size man-
ually. (Refer to “Manually selecting the desired paper size” on page 3-25.)
Manually selecting the desired paper size
The paper size can be specified for copying. By also selecting the “Auto 
Zoom” setting, the most appropriate zoom ratio is selected based on the size 
of the loaded document and the specified paper size. For details on the “Au-
to Zoom” setting, refer to “Automatically selecting the zoom ratio (“Auto 
Zoom” setting)” on page 3-27.
1In the Basics screen, 
touch [Paper].
The Paper screen ap-
pears.
Downloaded From ManualsPrinter.com Manuals