Konica Minolta bizhub 362 User Manual

							3Basic copy operation
3-6 362/282/222
Basic copy operation
Chapter 3
2Set the “Book Copy” 
function.
The “4 in 1” setting is au-
tomatically canceled, 
and the“Book Copy” 
function is set.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-7
Basic copy operation
Chapter 3
Operations where the setting specified first is given priority
If a warning message appears, indicating that settings cannot be combined, 
those settings cannot be specified together.
The procedure for selecting the “Corner Staple” setting after setting the 
“Booklet” function is described below.
1Set the “Booklet” func-
tion.
2Select the “Corner Sta-
ple” setting.
The message “This 
mode is not available 
with Booklet.” appears 
and the “Corner Staple” 
setting cannot be select-
ed.
The “Booklet” function 
remains selected and 
the “Corner Staple” set-
ting is canceled.
To select the “Corner Staple” setting, cancel the “Booklet” function, 
and then select the “Corner Staple” setting.
Downloaded From ManualsPrinter.com Manuals 
						

							3Basic copy operation
3-8 362/282/222
Basic copy operation
Chapter 3
3.3 Feeding the document
The document can be loaded into the optional ADF or positioned on the orig-
inal glass.
To load the document into the ADF
0Do not load documents that are bound together, for example, with paper 
clips or staples.
0For details on the types of documents that can be loaded into the ADF, 
refer to “Original documents” on page 7-17.
0Do not load more than 80 sheets or so many sheets that the top of the 
stack is higher than the , mark, otherwise a document misfeed or dam-
age to the document or machine may occur. However, a document that 
exceeds 80 pages can be scanned in separate batches. For details, refer 
to “Scanning a document in separate batches (“Separate Scan” setting)” 
on page 3-12.
0If the document is not loaded correctly, it may not be fed in straight or a 
document misfeed or damage to the document may occur.
1Slide the adjustable doc-
ument guides to fit the 
size of the document.
Document feed methodFeatures
Using the ADF By using the ADF, a multi-page document can be fed auto-
matically, one page at a time. This feed method can also be 
used to automatically scan double-sided documents.
Using the original glass Place the document directly on the original glass so that it 
can be scanned. This method is best with books and other 
documents that cannot be fed through the ADF.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-9
Basic copy operation
Chapter 3
2Load the document face 
up in the document feed 
tray.
– Load the document 
pages so that the top 
of the document is 
toward the back or 
the left side of the 
machine.
3Slide the adjustable doc-
ument guides against 
the edges of the docu-
ment.
– For details on load-
ing documents of 
mixed sizes, refer to 
“Copying documents 
of mixed sizes 
(“Mixed Original” 
setting)” on 
page 3-16.
– For details on select-
ing the orientation of the document, refer to “Selecting the docu-
ment orientation (Original Direction settings)” on page 3-19.
– For details on specifying the binding margin position, refer to “Se-
lecting the position of the binding margin (Margin settings)” on 
page 3-21.
AA
Adjustable document guide
Downloaded From ManualsPrinter.com Manuals 
						

							3Basic copy operation
3-10 362/282/222
Basic copy operation
Chapter 3
To place the document on the original glass
0For details on the types of documents that can be placed on the original 
glass, refer to “Original documents” on page 7-17.
0When placing the document on the original glass, be sure to lift open the 
original cover or ADF at least 15°.
If the document is placed on the original glass without the original cover 
or ADF being lifted at least 15°, the correct document size will not be de-
tected.
0Do not place objects weighing more than 4-1/2 lb on the original glass. In 
addition, do not press down extremely hard on a book spread placed on 
the original glass, otherwise the original glass may be damaged.
0For thick books or large objects, make the copy without closing the orig-
inal cover or ADF. When a document is being scanned with the original 
cover or ADF open, do not look directly at the light that may shine through 
the original glass. Although the light that shines through the original glass 
is bright, it is not a laser beam and, therefore, is not as dangerous.
1Lift open the original cover or ADF.
2Position the document face down onto the original glass.
– Load the document pages so that the top of the document is to-
ward the back or the left side of the machine.
15˚ 15˚
When loaded in the
w orientation:When loaded in the
v orientation:
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-11
Basic copy operation
Chapter 3
3Align the document with 
the   mark in the 
back-left corner of the 
document scales.
– For details on select-
ing the orientation of 
the document, refer 
to “Selecting the 
document orienta-
tion (Original Direc-
tion settings)” on 
page 3-19.
– For details on speci-
fying the binding margin position, refer to “Selecting the position of 
the binding margin (Margin settings)” on page 3-21.
– For transparent or 
translucent docu-
ments, place a blank 
sheet of paper of the 
same size as the 
document over the 
document.
– For bound docu-
ments spread over 
two facing pages, 
such as a book or 
magazine, position 
the top of the docu-
ment toward the 
back of this machine 
and align the spine of 
the document with 
the book mark in the 
document scale, as 
shown.
– For details on copy-
ing books, refer to “Producing separate copies of each page in a 
page spread (“Book Copy” function)” on page 8-18.
4Close the original cover or ADF.
Document scales
Blank sheet 
of paper
Downloaded From ManualsPrinter.com Manuals 
						

							3Basic copy operation
3-12 362/282/222
Basic copy operation
Chapter 3
Scanning a document in separate batches (“Separate Scan” setting)
A large document can be divided and continuously scanned in a number of 
batches.
A maximum of 80 document pages can be loaded into the ADF at one time. 
However, by copying with the “Separate Scan” setting, a document that ex-
ceeds 80 pages can be scanned and treated a s  a  s i n g l e  c o p y  j o b .  I n  a d d i t i o n ,  
the scanning location can be switched between the original glass and the 
ADF during the scanning operation.
1In the Application 
screen, touch [Separate 
Scan].
– To cancel the “Sepa-
rate Scan” setting, 
touch [Separate 
Scan] again to dese-
lect it.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-13
Basic copy operation
Chapter 3
2Load the first batch of 
the document, and then 
press the [Start] key.
Scanning begins.
The message “To con-
tinue scanning, replace 
original and press Start.” 
appears.
– Load the next batch 
of the document, and 
then press the [Start] 
key.
– If the document cannot be loaded into the ADF, place it on the orig-
inal glass. For details on the types of documents that can be loaded 
into the ADF, refer to “Original documents” on page 7-17.
– Repeat step 2 until all pages of the document have been scanned.
The amount of memory available can be checked beside “Memory 
Free” in the lower-right corner of the Basics screen.
– To delete the scanned image, press the [Stop] key, and then delete 
the job. For details, refer to “Stopping/deleting a job” on page 3-63. 
In addition, the job can be deleted from the Job List screen. For de-
tails, refer to “To delete a job” on page 4-25.
3After all document pages have been scanned, touch [Finish].
4Press the [Start] key.
Downloaded From ManualsPrinter.com Manuals 
						

							3Basic copy operation
3-14 362/282/222
Basic copy operation
Chapter 3
Scanning a multi-page document from the original glass
When making double-sided or combined copies using the original glass, 
place each page of a multi-page document on the original glass to scan it. 
The following procedure describes how to place single-sided document 
pages on the original glass to make double-sided copies.
1Lift open the original cover or ADF.
2Position the first page or the first side of the document face down onto 
the original glass.
– For details on positioning the document, refer to “To place the doc-
ument on the original glass” on page 3-10.
3Close the original cover or ADF.
4In the Basics screen, 
touch [Simplex/Duplex].
The Simplex/Duplex 
screen appears.
15˚ 15˚
When loaded in the
w orientation:When loaded in the 
v orientation:
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-15
Basic copy operation
Chapter 3
5Touch [Single-Sided] un-
der “Original” and [Dou-
ble-Sided] under 
“Copy”.
6Press the [Start] key.
Scanning begins.
The message “To con-
tinue scanning, replace 
original and press Start.” 
appears.
7Position the second page or second side of the document onto the 
original glass, and then press the [Start] key.
– To scan the remaining pages in the document, repeat steps 5 
through 7.
8After all document pages have been scanned, touch [Finish].
9Press the [Start] key.
Downloaded From ManualsPrinter.com Manuals