GTE Omni Si Database Technical Practices Issue 1 Manual

							TL-130100-1001STEPOPERATIONRESULT
6Release feature button.Display remains.
7Continue down the button row(s)
performing Steps 5 and 6 above.Same as Steps 5 and 6 above.
82-3 seconds after last button is
released.(I) Double beep heard.
(2) Display clears.
(clDisplay Test (Test Code 4)
STEPOPERATIONRESULT
1Depress & hold #.(a) Beep heard.
(b) “DIAGNOSTICS”
2Release #.“WHICH TEST =?‘I
3Depress 4.(a) The following each appear for 2-3
seconds in sequence.
(1) “DISPLAY TEST”
(2) All 
LCDs active.
(3) Blank display
(4) Alpha 1: “ABCDEFGHIJKLM”
(5) Alpha 2: “NOPQRSTUVWXYZ”
(6) Numeric: “1234567890”
(7) Special Characters: 
“*# + /:?&.I’(b) Display clears.
NOTE:Depress and hold designated feature button firmly until the required number of beeps
are received.
5210
3.4Programming Control ParametersAll control functions are programmed to default values in the initial
downloading operation (except time and date). The 
FeatureComm III/IV has
preprogrammed levels of pitch and volume for the station ringer, timing for a
Pause, Call Forwarding, and display format for Time and Date (Clock). The
controls are programmable and may be changed by utilizing the following
Control Codes (see Table 3.8 and the following examples). Control
programming is accessed by depressing
*; administration (set time and date)
by 0.
8187o-57 
						

							TL-130100-1001Table 3.8 Control Codes
CONTROL CODES
CODES
2Ring Pitch
3Ring Volume
5Clock Display
6
7Clock Type
Pause Duration
8Call Forward On No Answer
Duration
9Preference (Multi-Line Sets Only)
3.4.1Call Forward on No Answer Duration (Control Code 8)
STEPOPERATIONRESULT
1Depress and hold *.(a) Beep heard.
(b) “CONTROL PROGRAM”
2Release *.“WHICH CONTROL = ?‘I
3
Depress 8 (Control code for CALL
FORWARD).“FWD NO ANS = IOSEC”
NOTE:Any of these timing choices may be selected. If number 1 is selected, calls will be
forwarded after 10 seconds; number 2 after 20 seconds; and number 3 after 30
seconds.
4Enter the appropriate number.(a) “FWD NO ANS = 10SEC” if 1 is
entered.
(b) Beep heard.
(c) “NEW ENTRY STORED”
5
6Depress and hold *.
Release *.Display clears.
O-58
81875210 
						

							TL-130100-1001
3.4.2Clock Display (Control Code 5)
STEPOPERATION
RESULT
1
2
3NOTE:
7Depress and hold 
*.(a) Beep heard.
(b) “CONTROL PROGRAM”
Release 
*.Depress 5.
Choose one of the following:“WHICH CONTROL = ?”
111= DISPLAY; 0 = NONE”
1 
- To display time and date whenever the station is idle (feature button not
required).
0 
- For no display of time and date except via feature button operation
(reprogram a feature button to operate Time and Date).
Depress 1.“DISPLAY ON IDLE”
Depress 0.“NO IDLE DISPLAY”
Depress and hold 
*.(a) Beep heard.
(b) “NEW ENTRY STORED”
Release 
*.Display clears.
3.4.3
Clock Type (Control Code 6)STEP
OPERATIONRESULT
Depress and hold 
*.Release 
*.Depress 6 (Control Code for Clock
Type).Depress 1.
OR(a) Beep heard.
(b) “CONTROL PROGRAM”
“WHICH CONTROL = 
?”“1 = 12HR; 2 = 
24HR”“CLOCK = 12 HOUR”
5Depress 2.“CLOCK = 24 HOUR”
52108187o-59 
						

							--TL-130100-1001
OPERATIONRESULT
NOTE:Choose the desired clock type and depress the appropriate key. If 
12-hour time is
chosen, the HH:MM is followed by A or P for AM or PM, respectively. If 24-hour
time is chosen, the HH:MM display will not be followed by an A or P, and HH will
range from 00 to 23.
6Depress and hold *.(a) Beep heard.
(b) “NEW ENTRY STORED”
7Release *.Display clears.
Pause Duration (Control Code 7)
STEP
OPERATIONRESULT
Depress and hold *.(a) Beep heard.
(b) “CONTROL PROGRAM”
Release 
*“WHICH CONTROL = ?”
Depress 7 (Control Code for Pause
Duration).“PAUSE = 
?”
NOTE:Choose one of the following:
2, to program a 2.0 second Pause Duration
3, to program a 2.5 second Pause Duration
4, to program a 3.0 second Pause Duration
4Depress and hold *.(a) Beep heard.
(b) “NEW ENTRY STORED”
5Release *.Display clears.
NOTE:If an invalid entry is made, a triple beep will sound indicating an error. The selection
process may continue at this point.
Preference (Multi-Line Sets Only; Control Code 9)
STEPOPERATIONRESULT
1Depress and hold *.(a) Beep heard.
(b) “CONTROL PROGRAM”
O-60
81675210 
						

							TL-130100-1001STEPOPERATlONRESULT
2Release *.“WHICH CONTROL = ?”
3Depress 3 (control code for
preference).“PREF = 
10100”
4Depress * to see preference types.“PREF = R l P L I”
5Enter 0 for OFF or 1 for ON.
6
7Depress # to go to next field.
Continue for 5 fields.
Depress and hold 
*.
OS and 1s as entered.
“XXXXK“NEW ENTRY STORED”
8Release *.Display clears.
5210Preference Types
The five different types of preference include Incoming and Outgoing.
R=Incoming Ringing: The line with an incoming call, with audible alerting,
will automatically be seized when going off-hook.
I= Incoming, Non-Ringing: The line with an incoming call, with visual
alerting only, will automatically be seized when going off-hook.
P=Prime Line: The line that is the prime control line will automatically be
seized when going off-hook to originate a call. The secondary LED
associated with this line button will remain on steady to indicate this prime line
preference.
L= Last Line Used: The line that was last used will automatically be seized
when going off-hook to originate a call. The secondary LED associated with
this line button will remain on steady to indicate this last line used preference.
I= Idle Line: Any one idle line on the instrument will automatically be seized
when going off-hook to originate a call. The secondary LED associated with
this line button will remain lit steady to indicate this idle line preference.
For any combinations of the different types of preference, incoming and
ringing has the highest priority down to idle line, which has the lowest priority.
For example, if preference has been programmed for incoming, ringing, and
prime line, the I-Use LED for the prime line will always be on when 
on-hook; but if an incoming call is received, and the handset lifted, the ringing
line will automatically be seized.
8187
O-61 
						

							TL-130100-1001
Preference selection is intended to be dynamic and constantly changing as
the lines are made busy and go idle. The choosing of a line by a preference
feature is intended to mean its “predesignation for use” if and when the
instrument user goes off-hook. This should not imply either a reservation of
a line or seizure of the line.
3.4.6
Ring Pitch (Control Code 2)
STEPOPERATIONRESULTDepress and hold *.
Release *.Depress 2. (Control program for
pitch.)
Depress desired tone (l-8).
Adjust pitch as desired by
depressing the appropriate numberIf no entry is made, the last tone
sounded is the programmed pitch.
Release 
*.
(a) Beep heard.
(b) “CONTROL PROGRAM”“WHICH CONTROL = 
?”“TONES = 1 through 8”
(a) “PITCH = 
1”
(b) Ringing heard for about 1 second.(a) Display reflects number.
(b) Ringing tone higher.
(a) Beep heard.
(b) “NEW ENTRY STORED”
Display clears.3.4.7Ring Volume (Control Code 3)
STEP
OPERATIONRESULT
1Depress and hold *.(a) Beep heard.
(b) “CONTROL PROGRAM”
2Release *.
3
Depress 3.
4Depress desired volume (l-8)“WHICH CONTROL = 
?”“VOLUME = 1 through 8”
(a) “VOLUME = 
1”
(b) Ringing heard for about 1 second.
5Adjust volume as desired by entering(a) Display reflects number.
the appropriate number.(b) Ringing tone higher.
O-62
81875210 
						

							TL-130100-1001STEPOPERATIONRESULT
6Depress and hold *.(a) Beep heard.
(b) “NEW ENTRY STORED”
7If no entry is made, the last level
sounded will be the programmed level.
8Release *.Display clears.
NOTE:If you have a FeatureComm III/IV instrument, the preprogrammed Ring Volume is 1.
If you have a FeatureComm V/VI, it is 4.
3.4.8
Setting the Time and Date
STEPOPERATIONRESULT
1
2
3
8
NOTE:Depress and hold 0 (Access Code for(a) Beep heard.
Administration).(b) “ADMINISTRATION”
Release 0.
“QO:OOA DAY OO/OO”Enter hours (01-12 or 00-23), 
#,minutes 
(00-59) #.
“XX:XXA DAY OO/OO *”Enter AM/PM (A or P in 12 hr mode,
no entry 24 hr), #.
“XX:XXA DAY OO/OO *”Enter day, #.
“XX:XXA MON QO/OO” if Monday entered.
Enter month 
(01-12) #, date (01-31).“XXXXAMON XX/XX”
Depress and hold 0.“XXXXAMON 
XX/XX” time and date as
entered.
Release 0.Display clears.
* appears in the display indicating that other information is available.
3.5Function Codes, Feature Button Assign,ment and Data EntryFeature buttons are programmed/reprogrammed as outlined in the following
paragraphs and charts. Codes required for the various functions are shown
in alphabetical and numerical order in Tables 3.9 and 3.10, respectively.
52108187O-63 
						

							rTL-4 30100-l 001
Table 3.9 Function Codes Required for Programming/Reprogramming the Feature
Buttons, Listed Alphabetically
FUNCTION CODEFUNCTION
CODEAccount Code
Automatic Call Announcing
Automatic Callback
Automatic intercom
Bad Line
Busy Override
Call Announce
Call Forward
Call Hold
Call Park
Call Waiting
Conference
Data Option
Data Protection
Dial Display
Direct Station Selection (DSS)
Dual Access
Executive Priority Call
Extended Call Pickup
Extended Group Select
Flash
Forced Busy
Group/Directed Call Pickup
Intercom
Last Number Redial
40
27
37
2345
34
26
19
21
32
30
38
41
33
16
11
16
35
29
12
03
36
28
22
06Lines (Multi-Line Sets Only)
Manual Signal
Message Leaving
Message Waiting
Monitor
New Call
Privacy Release
Release
Reminder
Report Tone
Repertory/Feature Access
Ringer Cutoff
Save Number Redial
Shift
Speakerphone
Special Call Forward
Special Call Wait
Station Lock
Station Speed Calling
System Speed Calling
Timer/Elapsed Time
Time and Date (Clock)42
39
2524
04
0546
17
1344
09
01
07
43
18
20
31
02
0847
14
15O-64
81875210 
						

							TL-130100-1001Table 3.10 Function Codes Required for Programming/Reprogramming the Feature
Buttons, Listed by Code
CODE
FUNCTIONCODEFUNCTION
00
01
:;
04
05
06
ii;:
09
10
11
E
14
:z
:;
19
20
21
22
23Unassigned
Ringer Cutoff
Station Lock
Flash
Monitor
New Call
Last Number Redial
Save Number Redial
Station Speed Calling
Repertory/Feature Access
Dual Access
Direct Station Selection (DSS)
Extended Group Select
Reminder
Timer/Elapsed Time
Ti.me & Date (Clock)
;;;;seWySpeakerphone (Optional)
Call Forward
Special Call Forward
Call Hold
Intercom*
Automatic Intercom*
NOTE:Any number of buttons can be programmed to perform:
- Save Number Redial
- Repertory/Feature Access
- Dual Access
- Secretarial Answering Service (DSS)
- Automatic Intercom
- Automatic Call Announcing
- Manual Signal
- Lines (Multi-Line Sets Only)
*Requires special programming.Message Waiting
Message Leaving
Call Announcing
Automatic Call Announcing
Group/Directed Call Pickup
Extended Call Pickup
Call Waiting
Special Call Wait
Call Park
Data Protection
Busy Override*
Executive Priority 
CalT”Forced Busy
Automatic Callback
Conference
Manual Signal
Account Code*
Unassigned Data Option
Line (Multi-Line Sets Only)
Shift
Remote Tone
Bad Line
Privacy Release
System Speed Calling*
5210
8187O-65 
						

							TL-130100-I 0013.51
Programming/Reprogramming a Feature on a Button
STEPOPERATIONRESULT
1
2
3
4
NOTE:
5
6
NOTE:
7
8
9
O-66Remain on-hook.
Depress and hold feature button to
be assigned change.(a) Single beep heard.(b) “FEATURE NAME” of existing feature
displayed.
Release the feature button.
(a) LED flashes throughout programming.(b) “CONTENTS STORED” or “FEATURE
NAME” displayed.
Depress and hold 2.
(a) Double beep heard.(b) “CHANGE FUNCTION”
Release 2.
(a) LED flashes.(b) “FUNCTION CODE =
.I’-The 
* indicates that additional information is available. Repeated depressions of the *
will display the features and function codes in a scrolling action. Tables 3.9 and 3.10
show the code numbers to be entered to select a function for a feature button.
Entered desired function code(a) “CODE NUMBER = XX”
via keypad number (2 digits).
(b) “FEATURE NAME” displayed.
Depress 
# where XX represents the
code number digits.If 
# is not entered in Step 6, three beeps will be heard, the phone will EXIT
programming and the display will clear or revert to time and date.
Depress and hold the feature button.(a) Single beep heard.(b) “NEW ENTRY STORED”
Release feature button.(a) LED off.(b) Display clears or reverts to time
and date.
Change the feature button label to
reflect the new feature selected.
To Verify
1.
2.
Depress and hold the
button changed.
Release button and pressagain. Display clears or
reverts to time and date.(a) Beep heard.(b) 
“ABCD--” name of feature
programmed.
81875210