GTE Omni Si Database Technical Practices Issue 1 Manual

							TL-130100-1001NOTE:Speed Calling numbers are grouped by data base in 25 different sublists. The
access to a particular 
sublist can be restricted in data base, by group speed calling
access class (set of sublists) assigned to the line originating a group speed call.
4.29
4.29.1
Timed-Reminder
Timed-Reminder Activation
STEPOPERATIONRESULT
1
2
NOTES:
1.
2.
3.
4.
3Depress idle LOOP pushbutton
(1-4).(a) LOOP LED on.
(b) POS RLSE LED on.
(c) START/STOP LED on.
(d) Dial tone heard.
Dial timed-reminder access code,
station number, and time.(a) START/STOP LED off.
(b) 60-IPM tone heard. If time invalid,
120-IPM tone heard.
(c) Dialed digits appear on fixed display.
Where station numbers are of three- and four-digit format, four digits must be
dialed for all entries. If a station number is of three-digit format, dial a # after the
three digits.
A five-digit reminder time must be dialed for all entries; the first digit is either 2 (or
A) for AM or 7 (or P) for PM, and the remaining four digits are the hour and minute.
The time may not exceed 24 hours from the current time.
See Table 4.1 for time code conversion.
Depress POS RLSE pushbutton.(a) POS RLSE and LOOP 
LEDs off.
(b) Fixed display off.
(c) TOD displayed.
4.29.2
Timed-Reminder Deactivation
STEPOPERATIONRESULT
1Depress idle LOOP pushbutton
(l-4).(a) LOOP and POS RLSE LEDs on.
(b) START/STOP LED on.
(c) Receive dial tone.
52108187O-207 
						

							TL-130100-1001
STEPOPERATION
RESULT.:,
2
3Dial timed-reminder cancel code and
(a) START/STOP LED off.
station number.(b) Dialed digits appear on fixed display.
Depress POS RLSE pushbutton.
(a) LOOP and POS RLSE LEDs off.
(b) Fixed display goes off.
(c) TOD displayed (see Table 4.1 for time
code conversion).
4.30Message WaitingSTEPOPERATIONRESULT
1Depress idle LOOP pushbutton
(l-4).
2
3Depress MESG WTG pushbutton.
Dial station directory number.
Three digit station number must be
preceded by 
# key.
4Depress MESG WTG pushbutton.
5Depress MESG WTG pushbutton.
6Depress POS RLSE pushbutton.(a) LOOP LED on.
(b) POS RLSE LED on.
(c) START/STOP LED on.
(d) Dial tone heard.
MESG WTG LED on.
(a) Fixed display contains dialed digits.
(b) If station had message waiting active,
MESG WTG LED flashes and MESG
WAlTiNG displayed in fixed display,
otherwise MESG WTG LED off and NO
MESG WTG displayed in fixed display.
(c) START/STOP LED off.
Message waiting status changed from
Step 3.
Message waiting status changed from
Step 4.
(a) MESG WTG LED off.
(b) LOOP LED off.
(c) POS RLSE LED off.
(d) Fixed display field cleared.
(e) TOD displayed.
O-208
81875210 NOTE:
If message waiting is activated, the LED associated with the station user telephone
continues to flash until the station user dials the message center station number (this
can be an attendant). The LED does not flash if the station is ringing or off-hook. 
						

							TL-130100-10014.31Most Economical Route Selection (MERS) Active Time Zone
DisplaySTEP
OPERATIONRESULT
1Depress idle LOOP pushbutton
(l-4).
2Dial access code for active MERS
time zone display.
3Dial end-time-display digit (digit I).4Depress POS RLSE pushbutton.(a) LOOP LED on.
(b) POS RLSE LED on.
(c) START/STOP LED on.
(d) Dial tone heard.
(a) Zone number in use displayed 
in-calling number display field.
(b) Dialed digits appear on fixed display.
(a) End time for the active time zone
displayed in calling-number display
field.
(b) Confirmation tone heard.
(c) START/STOP LED off.
(d) Dialed digits appear on fixed display.
(a) POS RLSE and LOOP 
LEDs off.
(b) Variable and fixed displays cleared.
(c) TOD displayed. (See Table 4.1 for time
code conversion.)
4.32
4.32.1
Most Economical Route Selection (MERS) Time Zone Control
MERS Time Zone Assignment
STEPOPERATIONRESULT
1Depress idle LOOP pushbutton
(1-4).(a) LOOP LED on.
(b) POS RLSE LED on.
(c) START/STOP LED on.
(d) Dial tone heard.
2Dial access code for MERS time
zone change.(a) Letter “L” displayed if no zone was
previously entered by attendant. If
attendant had entered a zone
number, that number is displayed.
(b) Dialed digits appear on fixed display.
3Dial new zone number (l-3).(a) Beginning time, if any, of previously
entered data displayed (Table 4.1).
(b) Dialed digits appear on fixed display.
5210Em7O-209 
						

							--TL-130100-1001
STEP
OPERATIONRESULT
4Dial first digit of two-digit hours
of beginning time data.(a) End time, if any, of previously entered
data displayed.
(b) Dialed digit appears on fixed display.
5Dial remaining beginning-time
and end-time data.(a) Confirmation tone heard.
(b) START/STOP LED off.
(c) Dialed digits appear on fixed display.
6Repeat Steps 1 through 5 to verify
that entered data is correct.
7Depress POS RLSE pushbutton.(a) POS RLSE and LOOP LEDs off.(b) Fixed and variable displays cleared.
(c) TOD displayed.
4.32.2
MERS Time Zone Cancellation
STEPOPERATIONRESULT
1Depress idle LOOP pushbutton.(a) LOOP LED on.
(b) POS RLSE LED on.
(c) START/STOP LED on.
(d) Dial tone heard.
2Dial access code for the MERS time(a) Confirmation tone heard.
zone cancellation.(b) The active time zone in use displayed.
(c) START/STOP LED off.
(d) Dialed digits appear on fixed display.
3Depress POS RLSE pushbutton.(a) POS RLSE and LOOP LEDs off.
(b) Fixed display cleared.
(c) TOD displayed.O-210
81875210 
						

							TL-130100-I 0014.33Call Park
STEPOPERATION
RESULT
1When conversing with outside
party or another station and
outside party wishes to speak to
another party at another station,dial call-park access code.
2Dial directory number of station to
park call.
3Station that call is parked on can
still originate or receive other calls.
4Contact party whose station call is
parked on (this is done by either
paging or telephoning the party ifthat party’s location is known).
5The party on whose station call is
parked answers by dialing call-park
answer code and parked-on station
number.
6Any station can pick up parked call
by dialing call-park answer code
and parked-on station number.
7If call is not picked up within predeter-mined time (up to 4 minutes), call auto-
matically rings parked-on station. If
call is not answered within predeter-
mined time, call is diverted to atten-
dant.
(a) EXCL SRCE LED on.
(b) Fixed display contains dialed digits.
(a) START/STOP LED off.(b) Original party parked on station.
(c) LOOP LED off.
(d) POS RLSE LED off.
(e) EXCL SRCE or EXCL DEST LED off if(f) 
Fked display cleared.
(g) Trunk and station identificationcleared from variable display.
(h) Class-of-service digits cleared if
present.(i) TOD displayed.
52106437o-21 1 
						

							TL-130100-1001
4.34Attendant Recall
STEP
OPERATION
RESULT1Incoming CO trunk call received at
(a) Ringing heard.
Attendant Console.
(b) LOOP LED (l-4) flashes at 120 
IPM
2Depress flashing LOOP LED
pushbutton.(a) LOOP LED on.
(b) “LOCAL” appears in fixed display field.
(c) Trunk number appears in variable
display field.
3
4
5
6
7
8Dial station number.
Call is answered at the station.
Depress POS RLSE pushbutton.
At the station, the hookswitch is
flashed and at the Attendant
Console all of the LOOP keys
are busy.
Digit 0 dialed at station.
Depress POS RLSE on Attendant
Console.(d) POS RLSE LED on.
(e) Ringing stops.
(f) Transmission established between
trunk and attendant.
(a) EXCL SRCE LED on.
(b) Incoming trunk placed on hold.
(c) Dialed digits displayed in fixed field.
(d) START/STOP LED off.
(e) 
Ringback tone heard.
(f) Station receives distinctive ringing tone.
(a) Ringing stops.
(b) 
Ringback tone stops.
(c) Transmission allowed between station
and attendant.
(a) Call released.
(b) LOOP, POS RLSE, and EXCL SRCE
LEDs off.
(c) TOD displayed.
(d) The fixed display is cleared.
(e) Station and trunk connected.
(a) Distinctive dial tone heard.
(b) Trunk placed on hold (excluded
from Communications only).
(a) 
Ringback tone heard at station.
(b) CALL WTG LED dialing if first level of
call waiting reached and flashes if
second level of call waiting reached.
(a) Previous call released from Attendant
Console.
(b) LOOP, POS RLSE, and EXCL SRCE
LEDs off.
(c) Display cleared.
(d) TOD displayed.
o-212
81875210 
						

							TL-130100-100110
11STEPOPERATION
RESULT
(e) Available LOOP LED flashes.
(f) Ringing heard.
9Depress flashing LED LOOP
pushbutton.(a) LOOP, POS RLSE and START/STOP
LEDs on.
(b) If station of Step 6 was next in queue,
station number, COS, and TRANSFER
appear on display.
(c) Ringing stops.
(d) Transmission established between
station and Attendant Console, or 
as.adata base option, a three-way
connection established among at-
tendant, station, and trunk.
Provide assistance required.
Depress POS RLSE pushbutton.(a) LOOP, POS RLSE and EXCL SRCE or
EXCL DEST 
LEDs off.
(b) Display clears.
(c) TOD displayed.
4.35Attendant Timed Recall
STEP
OPERATIONRESULT
Incoming trunk call received at
Attendant Console.
Depress flashing LOOP LED
pushbutton (l-4).(a) Ringing heard.
(b) LOOP LED (l-4) flashes at 120 IPM.
(a) LOOP LED on steady.
(b) 
;IK$AL” appears in fixed display
(c) Trunk number appears in variable
display field.
(d) POS RLSE LED on.
(e) START/STOP LED on.
(f) Ringing stops.
(g) Transmission established between
trunk and attendant.
3Dial station number into the system.(a) Incoming trunk placed on hold.
(b) EXCL SRCE LED on.
(c) Dialed digits displayed on fixed
display.
5210
8187/
O-213 ; 
						

							TL-130100-1001STEPOPERATIONRESULT(d) 
Ringback tone heard.
(e) Called station rings.
4Depress POS RLSE pushbutton.(a) Attendant Console released from call.
(b) Trunk receives 
ringback tone.
(c) LOOP LED off.
(d) POS RLSE LED off.
(e) EXCL SRCE or EXCL DEST LED off if
(f) 
Fked display cleared.
(g) Trunk and station identification
cleared from variable display.
(h) Class-of-service digits cleared if
present.
(i) TOD displayed.
5Allow time out (data base) to occur.LOOP LED flashes at 60 IPM.
6Depress flashing LOOP LED
pushbutton.(a) LOOP LED on steady and POS RLSE
(b) 
‘1.0 ANSWER” appears in fixed
display field.
(c) Called station number and 
class-of-service marks displayed.
(d) Transmission established between
trunk and attendant.
4.36
Attendant Access Check of All implemented Stations
STEPOPERATIONRESULT
1Depress an idle LOOP pushbutton
(1-4).(a) LOOP LED on.
(b) POS RLSE LED on.
(c) START/STOP LED on.
(d) Dial tone heard.
2Dial number of station to be tested.
(a) Station receives normal ringing
(1 second on, 3 seconds off).
(b) 
Ringback tone heard.
(c) Dialed digits appear on fixed display.
(d) START/STOP LED off.
3
O-21 4Take called station off-hook.
6187Transmission established between
attendant and station.
5210 
						

							rTL-130100-1001
STEPOPERATIONRESULT
4Place station on-hook.(a) Variable display cleared.
(b) TOD displayed.
5Depress POS RLSE pushbutton.(a) LOOP and POS RLSE LEDs off.
(b) Fixed and variable display cleared.
(c) TOD displayed.
6Repeat Steps 1’ th;ough 6 for all
stations.
4.37Attendant Call Splitting
STEPOPERATION
RESULT
1
2
3
4
55210Incoming trunk call placed to
appropriate number.
Depress flashing LED LOOP
pushbutton (l-4).
Dial valid three- or four-digit
station number.
Answer call at station.
Depress EXCL DEST pushbutton.
Em7(a) Ringing heard.
(b) LOOP LED (l-4) flashes at 120 IPM.
(a) Ringing stops.
(b) LOOP LED on.
(c) POS RLSE LED on.
(d) START/STOP LED on.
(e) Trunk number displayed in variable
display field.
(f) “LOCAL” appears in fixed display field.
(g) Transmission established between
trunk and attendant.
(a) EXCL SRCE LED on.
(b) Trunk placed on hold in exclude-
source state.
(c) Dialed digits displayed in fixed display.
(d) START/STOP LED off.
(e) 
Ringback tone heard.
(f) Station receives distinctive ringing.
(a) Ringing stops at station.
(b) 
Ringback tone stops at Attendant
Console.
(c) Transmission established between
station and attendant.
(a) EXCL DEST LED on.
(b) EXCL SRCE LED off.
(c) Station placed on hold in exclude-
destination state.
O-215 
						

							.-TL-130100-1001
STEPOPERATIONRESULT
(d) Transmission established between
trunk and attendant.
6Depress EXCL SRCE pushbutton.(a) EXCL DEST LED off.
(b) EXCL SRCE LED on.
(c) Trunk placed on hold in 
exclude-source state.
(d) Transmission established between
station and attendant.
7Depress EXCL SRCE pushbutton.(a) EXCL SRCE LED off.
(b) Transmission established between
trunk, attendant and station.
8Depress POS RLSE pushbutton.(a) EXCL DEST LED off.
(b) POS RLSE LED off.
(c) LOOP LED off.
(d) Trunk to station connection is
maintained.
(e) Variable and fixed displays cleared.
(f) TOD displayed.
4.38Priority Calls Directed to the Attendant
STEP
OPERATIONRESULT
1Access code for priority call is dialed(a) Ringing heard.
from a station.(b) LOOP LED (l-4) flashes at 120 IPM.
2
30-216Depress flashing LOOP LED.pushbutton (l-4).(a) LOOP LED on steady.
(b) “PRIORITY CALL” appears in fixed
display.
(c) Line number and class of service
appears in variable display field.
(d) POS RLSE LED on.
(e) START/STOP LED on.
(f) Ringing stops.
(g) Transmission established between
line and attendant.
Depress POS RLSE pushbutton.
8187(a) LOOP LED off.
(b) POS RLSE LED off.
(c) EXCL SRCE or EXCL DEST LED off if
(d) 
Fked display cleared.
5210