GE Vivid 7 User Manual

							Getting started
Vivid7/Vivid7 PRO Users Manual17
FC092326-03
S Video OutNTSC/PAL S-
VideoVCR or video 
monitorSignal level 1Vp-p
SVGA OutRGB high 
resolution videoComputer monitor
USBUniversal serial 
busPrinter
Ethernet10/100 Base-TX 
Ethernet IEEE 
8023Network device Socket Signal type Device type Note 
						

							Getting started
18Vivid7/Vivid7 PRO Users Manual
FC092326-03
Switching On/Off
To switch on the unit:
1. Switch on the circuit breaker on the rear of the unit (see 
Figure 1-4).
2. Press   (on/off button) on the top left of the control panel 
(see Figure 1-4).
After initialization the default scanning screen (2D mode) is 
displayed, the active probe being the one connected to the 
left most connector socket.
Switching off the unit
When the Vivid 7/Vivid 7 PRO is switched off, the system 
performs an automatic shutdown sequence. The unit can be 
switched off into two states.
• Standby mode: most of the system is powered down, but 
a certain portion of the unit remains energized. The standby 
mode allows a shorter reboot time when the system is used 
on a daily basis or moved from one place to another.
• Full shutdown: the entire system is shut down. It is 
recommended to perform a full shutdown at least once a 
week.
Full shutdown
After switching off 
the system, wait at 
least ten seconds be-
fore turning it on 
again.1. Press   (on/off button) on the top left of the control panel.
The Exit dialogue window is displayed.
 Figure 1-3: The Exit dialogue window 
						

							Getting started
Vivid7/Vivid7 PRO Users Manual19
FC092326-03
In case of total lock-
up of the system, 
hold the on/off but-
ton down a few sec-
onds to turn the 
system off.2. Select Shutdown.
The shutdown process takes a few seconds and is 
completed when the control panel illumination is turned off. 
To switch off before moving the unit, follow the additional steps 
below:
1. Set the circuit breaker to OFF.
2. Remove the plug from the mains power socket.
3. Secure the unit power cable around the cable storage 
hooks on the rear of the unit.
 Figure 1-4: The Circuit breaker and On/Off button
Standby mode
1. Press   (on/off button) on the top left of the control panel.
The Exit dialogue window is displayed (Figure 1-3).
2. Select Standby.
The system enters in standby mode.
If the unit is to be moved while in standby, follow the additional 
steps below:
1. Set the circuit breaker to OFF.
2. Remove the plug from the mains power socket.
F 1F1 
						

							Getting started
20Vivid7/Vivid7 PRO Users Manual
FC092326-03
At the new location:
1. Secure the power plug in the wall outlet.
2. Switch on the circuit breaker on the rear of the unit 
(Figure 1-4).
3. Press   (on/off button) (Figure 1-4).
When turning on a system in standby it takes a few seconds 
before it responds. Do not push the on/off button again during 
this period (A second push will initiate a full shutdown).
If the power cable is removed from the wall outlet the system 
will remain in Standby mode for approximately 15 min using an 
internal battery. If the system is unplugged for a longer time 
period a full shutdown is automatically performed.
The system can be used regardless of the battery level. The 
battery is automatically charged when the system is plugged to 
the wall outlet and the circuit breaker is switched on. It takes 
about 10 hours to charge a flat battery.
If the system is left in the OFF condition (Circuit breaker in the 
OFF position and system unplugged from the wall out let) for 
an extended period of time (3 to 5 days or more), the system 
may not boot up or may beep when turned ON. Should this 
occur, the system needs to recharge the UPS batteries. This 
could take 15 minutes to as long as 10 hours, depending on the 
battery age, system input voltage and system temperature.
To eliminate draining the UPS batteries, the system should 
remain plugged into the wall outlet with the circuit breaker in 
the ON position. 
						

							Getting started
Vivid7/Vivid7 PRO Users Manual21
FC092326-03
Moving and transporting the unit
Wheels
The wheels of the unit are controlled by the pedals situated 
between the front wheels of the unit (see Figure 1-5). 
Examine the wheels frequently for defects to avoid breaking or 
jamming.
 Figure 1-5: The Vivid 7/Vivid 7 PRO ultrasound unit pedalsWheel Characteristics
Front Swivel, swivel lock and full lock
Rear Swivel, but do not lock
1. Swivel lock pedal 
(Free position)
2. Full lock pedal 
(Free position)
3. Front wheel
12
3 
						

							Getting started
22Vivid7/Vivid7 PRO Users Manual
FC092326-03
Wheel operation
To engage the pedal in full lock
To release the brake
To engage swivel lock
Pedal Action
Press on pedal no. 2
Pedal Action
Press on pedal no.1
Pedal Action
Press on pedal no.1
12
12 
						

							Getting started
Vivid7/Vivid7 PRO Users Manual23
FC092326-03
To release swivel lock
Moving the unit
To prepare the unit to be moved
1. If not locked, push the keyboard console to its park position.
2. Turn the system off, including the circuit breaker (see 
page 18), and remove the plug from the wall.
3. Disconnect all cables linking the unit to any off-board 
peripheral devices and network.
Note the marks on 
each cable to recon-
nect them later.4. Secure the unit’s power cable.
5. Place all probes in the probe holder. Ensure that the probe 
cables do not protrude from the unit or interfere with the 
wheels.
The park port may 
also be used for a 
probe connection al-
though it is not ac-
tive.6. Ensure that no loose items are left on the unit
7. Unlock the brake (see page 22).
To ensure safety while moving the unit
1. Ensure that the keyboard console is in locked position.
2. Proceed cautiously when crossing door or elevator 
thresholds. Grasp the front handle grips or the back handle 
Pedal Action
Press on pedal no. 2
WARNINGDo not move the unit if the keyboard console is in free position.
Ensure that the hands of the patient are away from the console 
arm when moving the keyboard console. 
						

							Getting started
24Vivid7/Vivid7 PRO Users Manual
FC092326-03
bar and push or pull. Do not attempt to move the unit using 
cables or probe connectors. Take extra care while moving 
the unit on inclines.
3. Ensure that the unit does not strike the walls or door 
frames.
4. Ensure the pathway is clear.
5. Move the unit slowly and carefully.
6. Use two or more persons to move the unit over long 
distances or on inclines.
Transpor ting the unit
Take extra care when transporting the unit by vehicle. In 
addition to the moving precautions listed on page 23, follow the 
procedure described below.
1. If not locked, push the keyboard console to its park position.
2. Disconnect all probes and secure them in their boxes.
3. Ensure that the transporting vehicle is appropriate for the 
unit’s weight. The recommended load capacity is a 
minimum of 190 kg (419 lbs).
4. Park the vehicle on a level surface for loading and 
unloading.
5. Secure the unit while it is on the lift, to prevent rolling. Do 
not attempt to hold it in place by hand. Cushion the unit and 
strap the lower part so that it does not break loose.
6. Ensure that the unit is secured inside the vehicle. Secure it 
with straps to prevent movement while in transit.
7. Drive cautiously to prevent vibration damage.
Reinstalling at a new location
1. When the unit is in place at a new location, lock the wheel 
CAUTIONAvoid ramps that are steeper than 10 degrees.
WARNINGDo not move/lift the unit if the keyboard console is in free 
position. 
						

							Getting started
Vivid7/Vivid7 PRO Users Manual25
FC092326-03
brakes (see page 22).
2. Follow the installation procedure described on page 12.
Unit acclimation time
Following transport the unit may be very cold or hot. Allow the 
unit to acclimate before being switched on. Acclimation will 
take one hour for each 2.5 ºC increment when the unit’s 
temperature is below 10 ºC or above 40 ºC.
ºC02.557.510354042.5
ºF32 36.5 41 45.5 50 95 104 108.5
Hours43210023
ºC45 47.5 50 52.5 55 57.5 60
ºF113 117.5 122 126.5 131 135.5 140
Hours45678910 
						

							Getting started
26Vivid7/Vivid7 PRO Users Manual
FC092326-03
System description
System over view
 Figure 1-6: the Vivid 7/Vivid 7 PRO ultrasound system
1
2
3
4
5
6
78
9
10
11
12
13