Canon printer PIXMA MG5620 User Manual
Have a look at the manual Canon printer PIXMA MG5620 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
LCD Cannot Be Seen At All• If the POWER lamp is off: The machine is not powered on. Connect the power cord and press the ON button. • If the POWER lamp is lit: The LCD may be in the screen-saver mode. Press one of the buttons on the operation panel. 801
An Unintended Language Is Displayed on the LCDSelect the language you want to be displayed according to the following procedure.1. Press the HOME button and wait for about 5 seconds. 2. Select Setup on the HOME screen. LCD and Operation Panel 3. Select Device settings , then press the OK button. 4. Press the button 4 times, then press the OK button. 5. Use the button to select the language for the LCD, then press the OK button. 802
Print Head Holder Does Not Move to the Position for Replacing Check1 Is the POWER lamp off? Check if the POWER lamp is lit. The print head holder will not move unless the power is on. If the POWER lamp is off, close the operation panel and turn the machine on. While the POWER lamp is flashing, the machine is initializing. Wait until the POWER lamp stops flashing and remains lit, and then open the operation panel again. Check2 Is an error message displayed on the LCD? Close the operation panel, follow the Support Code (error number) displayed in the error message to resolve the error, and then reopen it. For details on how to resolve the error, refer to Support Code List . Check3 Has the operation panel been left open for 10 minutes or longer? If the operation panel is left open for more than 10 minutes, the print head holder moves to the position to protect it to prevent the print head from drying out. Close and reopen the operation panel to return the print head holder to the position for replacing. Check4 Has the machine been printing continuously for a long period? Close the operation panel, wait a while, then reopen it. If the machine has been printing continuously for a long time, the print head holder may not move to the position for replacing since the print head may overheat. Note • Opening the operation panel while printing moves the print head holder to the position to protect it. Close the operation panel, and reopen it after printing finishes. 803
Printer Status Monitor Is Not Displayed Check Is the printer status monitor enabled? Make sure that Enable Status Monitor is selected on the Option menu of the printer status monitor. 1. Open the printer driver setup window. How to Open the Printer Driver Setup Window 2. On the Maintenance sheet, click View Printer Status . 3. Select Enable Status Monitor on the Option menu if it is not selected. 804
Problems with Installation/Downloading Cannot Install the MP Drivers Easy-WebPrint EX Does Not Start Up or Easy-WebPrint EX Menu Does Not Appear How to Update MP Drivers in Network Environment Uninstalling IJ Network Tool 805
Cannot Install the MP Drivers• If the installation does not start even after the Setup CD-ROM is inserted into your computer'sdisc drive: Start the installation following the procedure below. 1. Select items as shown below. ◦ In Windows 8.1 or Windows 8, select the Explorer icon in Taskbar on Desktop , then select Computer from the list on the left. ◦ In Windows 7 or Windows Vista, click Start then Computer . ◦ In Windows Vista, click Start then Computer . ◦ In Windows XP, click Start then My Computer . 2. Double-click the CD-ROM icon on the displayed window. If the contents of the CD-ROM are displayed, double-click MSETUP4.EXE. If you cannot install the MP Drivers with the Setup CD-ROM, install them from our website. Note • If the CD-ROM icon is not displayed, try the following: • Remove the CD-ROM from your computer, then insert it again. • Restart your computer. If the icon is not yet displayed, try different discs and see if they are displayed. If other discs are displayed, there is a problem with the Setup CD-ROM. In this case, contact the service center. • If you are unable to proceed beyond the Printer Connection screen: 806
Note• The printer is not detected. Check the connection. may be displayed depending on the computer you use. Check1 Make sure that the USB cable is securely plugged in to the machine and the computer. Check2 Follow the procedure below to connect the machine and the computer again. 1. Turn the machine off. 2. Unplug the USB cable from the machine and the computer, then connect it again. 3. Turn the machine on. Check3 If you cannot resolve the problem, follow the procedure below to reinstall the MP Drivers. 1. Click Cancel . 2. Click Start Over on the Installation Failure screen. 3. Click Exit on the "PIXMA XXX" screen (where "XXX" is your machine's name), then remove the CD- ROM. 4. Turn the machine off. 5. Restart the computer. 6. Make sure that you have no application software running. 7. Insert the CD-ROM again, then install the MP Drivers. • In other cases: Reinstall the MP Drivers. If the MP Drivers were not installed correctly, uninstall the MP Drivers, restart your computer, and then reinstall the MP Drivers. Deleting the Unnecessary MP Drivers If you reinstall the MP Drivers, install the MP Drivers with the Setup CD-ROM or install them from our website. Note • If the installer was forced to be terminated due to a Windows error, the system may be in an unstable condition and you may not be able to install the drivers. Restart your computer before reinstalling. 807
Easy-WebPrint EX Does Not Start Up or Easy-WebPrint EX Menu Does Not Appear If Easy-WebPrint EX does not start up or its menu does not appear on Internet Explorer, confirm the following. Check1 Is Canon Easy-WebPrint EX displayed on the Toolbars menu in the Internet Explorer's View menu? If Canon Easy-WebPrint EX is not displayed, Easy-WebPrint EX is not installed on your computer. Install the latest Easy-WebPrint EX onto your computer from our website. Note • If Easy-WebPrint EX is not installed on your computer, a message asking you to install it may be displayed on the notification area on the desktop. Click the message, then follow the instructions on the computer screen to install Easy-WebPrint EX. • While the installation or download Easy-WebPrint EX is in progress, it is necessary to access the Internet. Check2 Is Canon Easy-WebPrint EX selected on the Toolbars menu in the Internet Explorer's View menu? If Canon Easy-WebPrint EX is not selected, Easy-WebPrint EX is disabled. Select Canon Easy-WebPrint EX to enable it. 808
How to Update MP Drivers in Network EnvironmentDownload the latest MP Drivers in advance. To obtain the latest MP Drivers, access our web site through the Internet and download the latest MP Drivers for your model. After uninstalling the MP Drivers, install the latest MP Drivers according to the regular procedure. When the connection method selection screen is displayed, select Use the printer with wireless LAN connection. The machine will be detected automatically in the network. After making sure that the machine is detected, install the MP Drivers following the on-screen instructions. Note • You can use the machine over a LAN without performing setup again. 809
Uninstalling IJ Network ToolFollow the procedure below to uninstall IJ Network Tool from your computer. Important • Even if IJ Network Tool is uninstalled, you can print over network or scan from the computer. However, you cannot change the network settings over network. • Log into a user account with administrator privilege. 1. Perform the procedure to uninstall IJ Network Tool. • In Windows 8.1 or Windows 8: 1. Select Control Panel from the Settings charm on Desktop > Programs > Programs and Features . 2. Select Canon IJ Network Tool from the program list, then click Uninstall. If the User Account Control screen appears, click Continue. • In Windows 7 or Windows Vista: 1. Click Start > Control Panel > Programs > Programs and Features . 2. Select Canon IJ Network Tool from the program list, then click Uninstall. If the User Account Control screen appears, click Continue. • In Windows XP: 1. Click Start > Control Panel > Add or Remove Programs . 2. Select Canon IJ Network Tool from the program list, then click Remove. 2. Click Yes when the confirmation message appears. When the message prompting you to restart your computer is displayed, click OK to restart your computer. 810